Autoease TL105 User manual

AUTO
EASE
FOR
TESLA MODEL S
TL105-3085
POWER LIFTGATE
MANUAL

facebook.com/autoease
This retrofit power tailgate lift assisting system opens
and closes your rear door by simply pressing a button.
It provides additional security and value to your vehicle.
Installation is designed for the do-it-yourself and comes
with various brackets depending on your car.
FEATURES
Support original remote to open/close gate.
Support front/rear button to open/close gate.
Still support manually open/close the gate.
Customizable gate height, suits to everyone.
Gate will bounce back automatically once it senses
obstacles while closing.
Sound alarm when tailgate is closing or opening.
Quiet motor, noise less than 50dB in 30cm distance.
Work in all weather conditions, operation temperature -
40 ℃～60℃.
NOTICE
1. Check parts & quantity in the accessories table. Must
use the brackets/screws provided by us if not stated.
2. Shut down engine before installation. Product must
be installed by qualified installers.
3. Strut assembly contains high pressure part, self-
disassembling the poles is prohibited.
4. Make protections of the car dash board, plastic and
metal surface, in case scratches during installation.
5. Secure all the cables/wires in the car in case loose
contact while driving.
6. The installation will take 1-2 hours, please follow the
manual patiently.

facebook.com/autoease
PART LIST
Pole
x2
Control Box
x1
Power
Cable
x1
OBD
Decoder
x1
Gate
Button
x1
Drill
x1
TOOLS (not included)
Screw
Driver
x1
Spanner
x1
Plastic
Wrench
x1
REMARK: Pictures for reference only, they may look different or not
reflect the real product while products being updated.

facebook.com/autoease
SCHEME
CONTROL BOX
① Control box power
② Left pole power
③ Left pole control
④ Right pole power
⑤ Right pole control
⑥N/A
⑦N/A
⑧ Button control

facebook.com/autoease
Installation Steps
1. Use plastic wrench to remove the panels in the rear door.
2. Use original pole bracket to fix our poles (bottom)
3. Use original pole bracket to fix our poles (top)
4. Routing the poles hall cable through the plastic cover as
picture.

facebook.com/autoease
5. Remove the plastic panel of rear door (right) for routing the
cables and hide inside.
6. Remove the plastic panel below glove box in the
passenger’s side
7. Remove the plastic panel of glove box in the passenger’s
side
8. Open the engine cover plate

facebook.com/autoease
9. Connect lift gate power to the battery
10. Route the power cable through slot in the passenger’s side
11. Locate the car OBDii port under driver’s seat, connect to
our OBD adapter for fob/remote control.
12. Fix the control box to the rear door with a screw like
picture.
OBD adapter for our
kit use

facebook.com/autoease
13. Locate original lock connector, connect to the liftgate lock
adapter
14. Drill hole for installing our tail gate control button
15. Tail gate button installed
16. Installation finished!

facebook.com/autoease
ATTENTION
Keep gate open when installation is completed. Start car
engine, now manually close the gate so the system can
initialize and ready for use.
FREQUENTLY ASKED QUESTIONS
1. How many ways to operate the gate
A. There are three common ways as below:
1) Use original remote - three click of UNLOCK key or
long press the OPEN key if your remote has
2) Use tail gate button provided by us –one click
3) Use original front dash UNLOCK button - three click
2. How to setup gate height
A. manually adjust the gate to a proper height, long
press the gate button until you hear a beep, done.
3. Gate not work properly
A. a) inspect power supply, include positive 12-16v,
negative connects, and fuse box
4. Gate cannot close to the end and not locked
A. a) slightly adjust the lock b) check if left/right poles
are reversed c) check control box wiring d) check if not
using screws in the box e) remove a little cushion in the
latch

facebook.com/autoease
5. Gate can only open to half of the height
A. a) slightly adjust the lock b) check if left/right poles
are reversed c) check control box wiring d) re-adjust the
gate height
6. Original remote/fob does not work
A. a) check the yellow control wire connection b) check
OBD connection if there is a decoder box c) Adjust the
click rhythm during the three click of UNLOCK key d)
long press the OPEN key if your remote has
7. Original remote/fob can open but not close the gate
A. Check if you have manually close the gate to initialize
the system. If not, try this –manually open the gate to a
proper height, long press gate button until you hear a
beep, click button once to close gate, done.