AutoLoc AUTMOTORCT2 Instruction Manual

©2009 The Hoffman Group L.L.C. All rights reserved. AUTMOTORCT - 1 of 2 Revised 2/17/09
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above
instructions. Installation by qualified automotive professionals is highly recommended.
OPTIONAL ACCESSORIES
SWITCH REMOTE KIT LINEAR ACUATOR
AutoLoc's quality switches are
compatible with any type of
installation. Durable construction
and corrosion resistant contacts
ensure a long life of smooth
operation.
YOU WANT EXTREME POWER? The AutoLoc linear
actuators are the ultimate accessory for installing power-
operated hoods,trunks, amp racks, tonneau covers, or any
other heavy-duty application.
From one of our
four button remotes you
can roll your windows up and
down, unlock and lock your
doors, trunk, or hood, open/close
your sunroof, remote start, turn on
your headlights, neon, or dome
light, alarm, operate your stereo,
or anything else you can think of.
Please call for details.
Program up
Press and hold the learn up button until the Red LED indicator lights up.
Press and hold a trigger button (1 - 8) for the desired amount of run time
to program the up travel distance. To stop programming, simply let go of
the trigger button. The up run time travel distance has now been
learned.
Note: Programming mode will exit after 5 seconds if no trigger buttons
are learned. A maximum of two minutes is allowed per input trigger.
Program down
Press and hold the learn down button until the Green LED indicator lights
up. Press and hold a trigger button (1 - 8) for the desired amount of run
time to program the down travel distance. To stop programming, simply
let go of the trigger button. The down run time travel distance has now
been learned.
Note: Programming mode will exit after 5 seconds if no trigger buttons
are learned. A maximum of two minutes is allowed per input trigger.
Program up/down (using one trigger button)
Press and hold the learn down button and the learn up button at the
same time until both indicator LED's light up (Red & Green). Press and
hold a trigger button (outputs 1 - 8) for the desired amount of run time to
program the up travel distance. To stop programming, simply let go of
the trigger button. After releasing the trigger button, the down run time
travel distance will be learned automatically. This will have the same
travel distance as the up run time. The up and down run time travel
distance has now been learned.
Note: Programming mode will exit after 5 seconds if no trigger buttons
are learned. A maximum of two minutes is allowed per input trigger.
Reset Mode
To reset the program module simply press the reset button. This will
erase the memory setting for all buttons.
Jumpers settings
Jumper 4 can be set to either 6amp or 10amp depending on how much
amperage is needed.
Sensitivity adjustment
Remove cover plate to access the adjustment screw. Use a small flathead
screw driver to adjust the load sensitivity. Turn clockwise to increase
sensitivity, turn counter clockwise to decrease sensitivity. This adjustment
will allow the motor to stop if there is an obstruction.
CAUTION: Do not overturn Sensitivity Adjustment Screw or damage
could result to the MotorCT unit.
1
2
3
6
5
4
AUTMOTORCT2 - 2 Channel
AUTMOTORCT4 - 4 Channel
AUTMOTORCT6 - 6 Channel
AUTMOTORCT8 - 8 Channel
IMPORTANT: The below instructions
are referring to an installation using
optional momentary push buttons (part
number S15). If you are installing this unit
using the optional remote control, then
connect the receivers negative(-) outputs to the
MotorCT modules negative(-) inputs(1-8).
If you need to use the optional push buttons or
optional remote control kit, please contact your sales
rep or visit our web site for secure online ordering.
MOTOR CONTROL MODULE
WWW.AUTOLOC.COMTECH SUPPORT: 503.693.1918
programmable motor control

©2009 The Hoffman Group L.L.C. All rights reserved. AUTMOTORCT - 2 of 2 Revised 2/17/09
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above
instructions. Installation by qualified automotive professionals is highly recommended.
RESET
6A 10A
SENSITIVITY ADJUSTMENT
(remove cover to access)
PROGRAM UP PROGRAM DOWN
BLUE/WHITE
GREEN/WHITE
Black
Red
part#
LAPLUG
WHITE
DIODE*
(1 or 2 amp.)
WHITE/BROWN
WHITE/BLUE
WHITE/BLACK
BROWN/WHITE
BROWN/GREEN
BROWN/BLUE
BROWN
15 Amp Fuse
Battery
12V
Battery
12V
Ground
Ground
1 2 3 4 5 6 7 8
GROUND
INCREASEDECREASE
UP LED
(RED)
DOWN LED
(GREEN)
OPTIONAL REMOTE
CONTROL RECEIVER
WIRING DIAGRAM
NEGATIVE OUTPUTS CONECTIONS
(from optional remote control)
OPTIONAL MOMENTARY
TRIGGER BUTTONS
(part # s15)
*NOTE: If you are using a remote control system and the momentary trigger buttons on the same MotorCT trigger inputs (1-8), you
must diode isolate the negative outputs from the remote control system.
AUTKL 550 - 5 channel AUTKL600 - 6 channel AUTKL700 - 7 channel AUTKL1000 - 10 channel AUTKL1600 - 16 channel AUTKL1800 - 18 channel
USER GUIDE AND INSTALLATION MANUAL
WWW.AUTOLOC.COMTECH SUPPORT: 503.693.1918