AV-GAD PIR-730 User manual

INSTALLATION
1. Avoid installation in outdoor, places with pets, air-
condition, heat source nearby, places with direct
sunshine and places under rotating objects.
2. Install on stable surface, without vibration.
3. Install the detector in places where an intruder may
passes easily.
INSTALLATION STEPS
1. Screw the bottom off and open the detector
2. Remove the PCB
3. Drill a wire hole in the rear housing
4. Install the rear housing in a suitable position
5. Fix the internal PCB
6. Connect the terminal block as follows
7. Place the detector cover
1
PIR-730 MAIN FEATURES
● MCU control, resist false alarm efficiently
● Double temperature compensation
● Pulse count adjustment
● White light interference immune
● RF interference immune (20V/m-1GHz)
● Fresnel lens optics
● Wall/ceiling installation
● Alarm output N.C. or N.O.
● Alarm timer optional (3s or 30s)
● Intelligent floating thresholds technology
● Enhanced appearance design
● SMT high stability production
PRODUCT INTRODUCTION
The PIR-730 is an high stability ceiling-mounted
passive infra red (PIR) detector. Adopts advanced
signal processing technology which provides high
detection ability and anti-false alarm ability.
MCU processing ensuring the reliability from
design basis. When an intruder passes through
the detection area, the detector will detect the
human body movements automatically. If any
movements, it will send alarm signal to the
connected alarm host. It suits for safety protection
in residential houses, villas, factories, shopping
malls, warehouses and office buildings etc.
TECHNICAL SPECIFICATION
Operation voltage: DC 9-16V
Current consumption: ≤18mA (DC 12V)
Detecting distance: Φ6m at 3.6m of ceiling installation
Detecting speed: 0.3m/s-3m/s
Detecting an: 360°
Self-testing time: 60s
Alarm time: 3s/30s optional
Alarm indication: Red LED
Sensor: Double element Pyroelectric infrared sensor
Operating temperature: -10℃~ +50℃
Environment humidity: ≤95% RH(no coagulation)
Anti RF interference: 10MHz-1GHz 20v/m
Instillation Mode: Ceiling mounted
Installation height: 2.5-3.6m
Alarm output: N.C. or N.O. (DC28V 100mA)
Tamper output: N.C. (DC28V 100mA)
Outline Size: Φ100*36mm
WIRING TERMINAL BLOCK FIGURE
+12V DC Positive
GND DC Negative
ALARM Relay contacts
TAMPER Protection Switch
PIR-730 Installation Manual
GND ALARM TAMPER
+12V
PIR-730
Item: 4727_730 (A5DS)

NOTICE
1. Install the detector properly according to manual.
Do not touch the sensor surface in order not to decrease
the sensitivity. If the sensor needs to be cleaned, use soft
cloth with little alcohol after cutting off the power.
2. The detector can decrease the rate of the accident but
can not assure no risk at all. For safety concern, besides
proper usage of the detector, please enhance vigilance
and take good protection in daily life.
3. Constant power supply should be provided to ensure
proper operation . Walking test should be carried out
periodically. Once a week is recommended.
OPERATING INSTRUCTION
Jumper setting
1) PULSE Jumper: Adjust sensitivity and the
detection speed.
Short 1&2: Class 1 pulse, high sensitivity, good anti
RF interference ability, suits for ordinary
environment.
Short 2&3: Class 2 pulse, low sensitivity, strong anti
RF interference ability, suits for environments with
heavy RF interference.
2) Relay Jumper: Choose N.C. or N.O. to set the
state of alarm output according to different
requirements of alarm host.
Short 1 & 2: N.O.
Short 2 & 3: N.C. (Default)
3) Delay Jumper: Used to set the lasting time of
relay and alarm indicator when alarming.
Short 1&2: 3S ( Default)
Short 2&3: 30S
4) LED Jumper: Used to control LED indicator. This
function will not influence the normal detector’s
operation. In order to provide better concealment,
the LED indicator can be off after test by pulling out
all the jumpers.
PRODUCT TESTING
Connecting power supply (DC12V), LED indicator flashes,
the detector will go into self testing state for about 60s.
When the LED indicator off, the detector enters into
normal working state. For testing walk within the detection
range in parallel with the wall where the detector is
installed. When the LED indicator lights, the detector
enters into alarm state.
JUMPER SETTING FIGURE
2
Top & Side views Detection Pattern PIR-730
DETECTING AREA VIEW
0m 6m
2m 4m 8m
3.6m
0m
2m
4m
2m
4m
0m 2m 4m2m4m
123
123
123
OPEN
2&3
1&2
1
RELAY JUMPER
2
LED JUMPER
3DELAY JUMPER
4PULSE JUMPER
1
2
34
LED On
Pulse count
Relay Mode
Delay
Av-Gad Systems Ltd. Panorama House
84, Ben Zvi Road, Tel-Aviv 68 104, Israel
P.O.B. 49 080, Tel-Aviv 61 490, Israel
www.av-gad.com
Tel: [phone]. Fax: [phone]