Ava QUAD Installation instructions manual

Mounting guide

Bullet • Mounting guide | 2
Important warnings and safety instructions
Avoid exposing the camera to shocks, high pressure or temperatures above 60OC.
Avoid placing the camera near fans, ventilation or other noise sources. This will degrade audio performance.
Avoid scratching or leaving ingerprints on the lens cover, this degrades image quality. If possible, keep the protective
plastic on the lens cover during installation.
Do not clean the camera with harsh detergents, gasoline or chemicals such as Acetone.
Do not try to repair the unit yourself. Refer all servicing of the camera to Ava or contact a reseller.
Disconnect power from the unit when performing a maintenance task.
This product should be supplied by a Power over Ethernet Power Sourcing Equipment (PSE) compliant to IEEE 802.3at Type 2 (PoE+).
The camera and the PoE PSE must be installed within the same building, as described by Environment A of the IEEE 802.3at
standard. The PoE PSE must be properly grounded.
Please contact AVA’s certiied dealers (or distributor) for power adapters.
The minimum ground screw type is 3.5mm.

Bullet • Mounting guide | 3
Overview
Outer view
Release
button IR LEDs
Threaded holes for
mounting adapter
Top mounting plate
Through holes for
ceiling-mount or wall
mount bracket
Dome cover
Top view

Bullet • Mounting guide | 4
Overview
Inner view Side track
Lens (sensor) module,
3-axis adjustable
Reset button
Cable gland
for ethernet
Status LEDs
Safety tether wire
RJ45
Ethernet port

Bullet • Mounting guide | 5
Camera mount - preparation
1 2
A
A
C
B
T10
x8
B
C

Bullet • Mounting guide | 6
Camera mount - preparation
3

Bullet • Mounting guide | 7
Ceiling mount
Cable hole
Cable hole
Drill hole
Drill hole
Drill hole
180mm
Alignment sticker
1 2

Bullet • Mounting guide | 8
In-ceiling mount
1 2
If needed, add hanging rods to strengthen the ceiling structure.
Weight of camera: 2.7 Kg
Weight of Recessed kit: 1.1 Kg
Hanging rod
Rail
Main keel
Secondary
keel ø15cm
Assemble the bracket rod with the two bracket stands and place the assembly at the desired
location before the screws are fastened.

Bullet • Mounting guide | 9
In-ceiling mount
3 4
Adjust the position relative to the ceiling tile, the mounting plate should be a little bit higher than
the lower edge of the ceiling tile. Make sure you can press the release button on the mounting
plate. Tighten the hex nuts when the adjustment is done.
Fasten the two nuts to secure the positions of the bracket stands on the hang rod. Remove the
assembly from the ceiling and install the ceiling tile.
Required:
ACQ-REC-KIT Recessed kit

Bullet • Mounting guide | 10
Pendant mount
1 2 3
Use the alignment sticker and drill holes for the Pendant head,
secure it with the screws.
Install the Pendant pipe and secure with the upper hex screw,
install the Mounting adapter and secure it with the lower hex screw.
Install the top mounting plate.
Note the front indicators indicate the default front side of the
camera. Install the mounting plate with the orientation you prefer.
Required:
ACQ-PEN-HEA Pendant head
ACQ-PEN-PIP Pendant pipe 40cm
ACQ-MNT-ADA Mounting adapter

Bullet • Mounting guide | 11
Wall mount
1 2 3
Attach the alignment sticker to the wall. Drill 4 holes for screws
and 1 hole for routing cables.
Leave one washer on each threaded pole. Connect the Ethernet
cable and use foam tapes or seal foam to ensure the back-end
connection is waterproof.
Route the cables along the routing guide poles to form drip loops.
Required:
ACQ-WAL-MNT Wall mount bracket
Ø9.5mm or 3/8”

Bullet • Mounting guide | 12
Wall mount
4 5 6
Secure the top mounting plate.

Bullet • Mounting guide | 13
Pole / Corner mount
1 3
Secure the top mounting plate.Install the Pole bracket to the pole wrapping the metal band around
the pole. Or install the Corner bracket to the corner using correct
type of screw.
Install the Wall mount bracket to the Pole or Corner bracket as
described on the previous page. Align the top mounting plate with
the center of the Wall mount bracket.
2
Required:
ACQ-WAL-MNT Wall mount bracket
ACQ-POL-MNT Pole bracket or ACQ-CRN-MNT Corner bracket

Bullet • Mounting guide | 14
Camera mount - final installation
1 32

Bullet • Mounting guide | 15
Camera mount - final installation
4 65
Adjust the image orientation in Ava Aware.
19cm
Mind the electrostatic damage by avoiding contact
with exposed circuitry.

Bullet • Mounting guide | 16
Camera mount - final installation
7 98
T10
x8