Avanti HC100 User manual

1
INSTALLATION MANUAL
Model Number: HC100 Hospitality Cabinet
CAUTION:
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING
INSTRUCTIONS.
Avanti has a policy of continuous improvement on its products and reserves the right to change materials and
specifications without notice.
Avanti Products
P.O. Box 520604 - Miami, Florida 33152
www.avantiproducts.com

2
•Thank you for purchasing our product, carefully read and follow all
assembly instructions before assembling this item.
•Please make sure that you have all the parts and hardware as
indicated before beginning the assembly of this item.
•Use the hardware illustrations to determine correct piece and size.
•This item should be assembled on a soft surface to prevent
scratching the finish during assembly.
•Do not tighten all the screws and/or anchors until you have a good fit.
This unit is supplied in an un-assembled state and must be assembled.
a) The unit is very heavy and should not be carried by one person.
To avoid injury to yourself and/or damage to the unit we recommend
you carry the unit between 2 or more persons.
b) Before assembly place all parts on a soft stable surface to avoid
scratching or damaging the finish.

3
Parts:
Part #
Part Description
Qty Included
1
Left Side Panel
1
2
Back Panel – Microwave Section
1
3
Back Panel – Refrigerator Section
1
4
Bottom Panel – Refrigerator Section
1
5
Front Fascia
1
6
Top Shelf Panel
1
7
Bottom Panel – Microwave Section
1
8
Door – Dry Storage Section
1
9
Bottom Panel – Dry Storage Section
1
10
Adjustable Shelf – Refrigerator Section
1
11
Right Side Panel
1

4
Assembly Hardware
Part No.
Illustration / Description
Qty included
A
Anchor Bolt and Lock
22 Pieces
B
Wood Dowel
32 Pieces
C
Shelf Pin
4 Pieces
D
Door Hinge
2 Pieces
E
ST3.5 X 15 – Screw
12 Pieces
F
Door Pull - Knob
1 Piece
G
ST4 x 20 - Screw
1 Piece
H
Magnetic Door Catch
1 Piece

5
Tools required to assembly this unit:
Be sure that you have the following at hand prior to beginning the assembly:
When installing the assembly hardware be sure that you insert all screws,
anchor bolts, and dowels straight and are flush to the surface of the unit.
Over tightening of the hardware will result in damage to the finish and a
poor fit.

6
STEP 1:
As shown in the illustration (fig. 1) attach the (2) back panels (parts 2 & 3) to the
left side panel.
Part
Description
1
Left Side Panel
2
Back Panel – Microwave Section
3
Back Panel – Refrigerator Section
Fig. 1
Assembly Parts Used
Part A:
Part B:

7
STEP 2:
As shown in the illustration (fig. 2) attach the (4) horizontal panels (parts 4, 5, 6, 7,
and 9) to the left side panel. As well as attach the magnetic (H1) portion to the
inside area of the storage compartment.
Part
Description
4
Bottom Panel – Refrigerator Section
5
Front Fascia
6
Top Shelf Panel
7
Bottom Panel – Microwave Section
9
Bottom Panel – Dry Storage Section
Fig. 2
Assembly Parts Used
Part A:
Part B:
Part H: (H1)

8
STEP 3:
As shown in the illustration (fig. 3) attach the right side panel (part 11) to the
panels installed in steps 1 and 2.
Part
Description
11
Right Side Panel
Fig. 3
Assembly Parts Used
Part A:
Part B:
STEP 4:
Once you have all of the wooden panels assembled and with a good fit, tighten
securely all anchor locks.

9
STEP 5:
As shown in the illustration (fig. 5) install the front storage door (part 8)and place
the refrigerator support shelf (part 10) in position. Install the metal catch (H2)
portion of the magnetic door catch to the storage door as shown below:
Part
Description
8
Door – Dry Storage Section
10
Adjustable Shelf – Refrigerator Section
Fig. 5
Assembly Parts Used
Part C:
Part D:
Part E:
Part F:
Part G:
Part H: (H2)

10