Aventura CAM-IPM-5D-41P-VP User guide

Network Camera
Quick Operation Guide
V4.0.1

Network Camera·Quick Operation Guide
1
1
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer. This
manual applies to CAM-IPM-5D-41P-VP, CAM-IPM-3D-29P-VP,
CAM-IPM-2D-29P-WDR, CAM-IPM-2D-29P-WDRI,
CAM-IPM-03D-21IR-VP Cameras
This manual may contain several technically incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards
as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS
PRODUCT.

Network Camera·Quick Operation Guide
2
2
1Appearance Description
1.1 Camera Description
Figure 1-1 Overview
Table 1-1 Description

Network Camera·Quick Operation Guide
3
3
No.
Description
1
10M/100M self-adaptive Ethernet interface
2
INITIAL SET: Reset button
3
AUDIO OUT: Audio output interface
4
MIC IN: Audio input interface
5
D+, D-: RS-485 interface
6
1A, 1B, 2A, 2B: Alarm output interface
7
IN1, GND, IN2, GND: Alarm input interface
8
Power supply interface
Note: After powering the camera on, pressing and holding the
INITIAL SET button for about 10 seconds can reset all the
parameters to the default settings.

Network Camera·Quick Operation Guide
4
4
1.2 Camera Wiring Diagram
Figure 1-2 Wiring Diagram

Network Camera·Quick Operation Guide
5
5
2Installation
Notes:
Verify the package contents are correct by checking the
items against the packing list.
Read the following contents carefully before the
installation.
Make sure that all the related equipment is powered-off
during the installation.
Check whether the power supply is matched with your AC
outlet to avoid damage.
Do not place the camera in extremely hot or damp
environment. To avoid heat accumulation, good ventilation is
required for a proper operating environment.
If the product does not function properly, please contact
your dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
Ceiling mounting:
Note: If required, you can use a plier to remove one clip or both
two clips (marked in dotted line in Figure 2-1) on the side of the
back box and then route cables through the opening to secure the
cables on the ceiling.

Network Camera·Quick Operation Guide
6
6
Figure 2-1 Side Clips
Steps:
1. Use the screws to fix the mounting base to the ceiling; rotate
the back box counterclockwise to secure it to the mounting
base; use the lock screw to secure the dome camera.
Figure 2-2 Mounting
2. Loosen the set screws with the hex key (supplied) to remove
the lower dome.

Network Camera·Quick Operation Guide
7
7
Figure 2-3 Disassembling
3. Connect the RCA analog video output with a monitor to view
the image of the camera. Loosen the lens set screw and pan,
tilt or rotate the lens to get a desired surveillance angle. Adjust
the lens focus to obtain a perfect image. Fasten the lens set
screw.
Figure 2-4 Image Adjusting

Network Camera·Quick Operation Guide
8
8
Figure 2-5 Image Adjusting
4. Reinstall the lower dome and tighten the screws.
Figure 2-6 Reinstall

Network Camera·Quick Operation Guide
9
9
In-ceiling mounting:
Steps:
1. Secure the mounting base to the in-ceiling mounting base with
screws.
Figure 2-7 Mounting Base
In-ceiling
mounting
base
Mounting
base

Network Camera·Quick Operation Guide
10
10
2. Push the dome camera to the in-ceiling mounting base, rotate
the dome camera for 10 degrees counterclockwise and then
fasten the lock screws to fix the camera.
Figure 2-8 Camera and Mounting Base
3. Cut a 176~180 mm diameter hole in the ceiling and push the
dome camera with in-ceiling mounting base to the hole.
Note: The thickness of the ceiling should be less than 30 mm.
①
②
③
Lock screw

Network Camera·Quick Operation Guide
11
11
Figure 2-9 Installing
4. It is strongly recommended that you use a safety rope to
secure the in-ceiling mounting base to the roof.
Figure 2-10 Safety Rope
5. Fasten the lock screws to secure the dome camera.
Safety rope

Network Camera·Quick Operation Guide
12
12
Figure 2-11 Fasten Screws
6. Remove the lower dome and connect the RCA analog video
output with a monitor to view the image of the camera. Loosen
the lens set screw and pan, tilt or rotate the lens to get a
desired surveillance angle. Adjust the lens focus to obtain a
perfect image. Fasten the lens set screw. Reinstall the lower
dome.
Figure 2-12 Image Adjusting
Lock Screw

Network Camera·Quick Operation Guide
13
13
7. Install the trim plate with screws to finish the installation.
Figure 2-13 Trim Plate Installing

Network Camera·Quick Operation Guide
14
14
3Setting the Network
Camera over the LAN
Purpose:
To view and configure the camera via LAN(Local Area Network),
you need to connect the network camera in the same subnet with
your PC. Then, install the SADP or iVMS-4200 software to search
and change the IP of network camera.
The following figure shows the cable connection of network
camera and PC:
Figure 3-1 Wiring over LAN
Set the IP address of the camera for accessing via LAN.
Steps:
1. To get the IP address, use the Aventura client software to list
the online devices. Please refer to the user manual of client
software for detailed information.
2. Change the IP address and subnet mask to the same subnet as
of your PC.

Network Camera·Quick Operation Guide
15
15
3. Enter the IP address of network camera in the address field of
the web browser to view the live video.
Note:
The default value of the IP address is “192.0.0.64”. The
default user name is “admin”, and password is “12345”.
For accessing the network camera from different subnets,
please set the gateway for the network camera after you
log in.

Network Camera·Quick Operation Guide
16
16
4Accessing via Web Browser
System Requirement:
Operating System: Microsoft Windows XP SP1 and above version /
Vista / Win7 / Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 6.0 and above version, Apple
Safari 5.02 and above version, Mozilla Firefox 3.5 and above
version and Google Chrome8 and above version
Before you start:
Check the security level of the web browser and change it to Low.
On the IE browser menu bar, navigate to Tools > Internet
options > Security > Custom level to customize the level to
LOW.

Network Camera·Quick Operation Guide
17
17
Figure 4-1 Adjust the Security Level
Steps:
1. Open the web browser.
2. In the browser address bar, input the IP address of the network
camera, e.g., 192.0.0.64 and press the Enter key to enter the
login interface.
3. Input the user name and password.
4. Click .

Network Camera·Quick Operation Guide
18
18
Figure 4-2 Login Interface
5. Install the plug-in before viewing the live video and managing
the camera. Please follow the installation prompts to install the
plug-in.
Note: You may have to close the web browser to finish the
installation of the plug-in.

Network Camera·Quick Operation Guide
19
19
Figure 4-3 Download Plug-in