Aventura VID-ALARM-8CH-COM User manual

VID-ALARM-8CH-COM
Reference Manual



Pleasereadtheseinstructionsandkeepforlaterreference.
NOTES:
1. Donotuseinextremeheatorcoldtemperatures.
2. Donotexposetorainormoisture
3. Donotexposetoflammable,explosive,orcorrosivegas.
4. Avoidexposuretodustorotherparticlesthatmaygetinsidetheequipment.
5. Useofextensioncordsmaysignificantlyincreaseriskoffire,electricshock,anddamagetotheequipment.
6. Toavoidriskofelectricshockanddamagetoequipmentdonotopenthedevice.
7. Professionalinstallationisrequired.

VID‐ALARM‐8CH‐COMReferenceManual2




A B C
D
a. 9PinDINFemaletoFemaleSerialAdapter
b. TerminatingResisters
c. PhoenixTypeConnectors
(1x4Screw/4x8Screw)
d. PowerAdapter
AdditionalItemsIncluded
BackPanel


FrontPanel
Brie
f
Intro
d
uction
Alarmin:8‐portNormalOpen/NormalCloseInputVoltage0~+15V
Alarmout:8‐portNormalOpen/NormalCloseconnector
PowerSupply:12VDC10W
OutputPower:10Aat28VDCor7Aat220VAC
Communicationtype:RS485,RS232
Workingtemperature:‐10degreeC‐‐70degreeC(inside)


VID‐ALARM‐8CH‐COMReferenceManual3

1.General
The DV7608 alarm box is a 8 channel alarm inputs, 8 channel controllable normally open relay
outputs alarm box, connected with digital video recorder to conduct single or full arm, disarm,
enquiry and switch controlling function.

2.MainFeatures
8 channel alarm inputs, 8 channel relay outputs (NO)
Alarm linkage function
Watchdog function, auto reset function in strong reference environment.
Open circuit and short circuit arm function
Provide protocol, 16 ID setting, connect up to 128 alarm probes at maximum.

3.Specification
PowerSupplyDC13.5V
PoweroutputDC12V/400mA
Auxiliaryrelay8normallyopenrelay,AC220V/2A
CommunicationRS485,RS232
ProtocolMulti‐protocolsettinguponrequirement,suchas
DCTRLS,W110,RM110,SE600,etc.
OperatingEnvironment‐10℃~70℃indoor

4.ConnectionDiagram


VID‐ALARM‐8CH‐COMReferenceManual4

5.BoardLEDIndication
AlarmoutLED,lightmeansrelayclosed,offmeansrelayopen
AlarminLED,longlightmeansinarmsetupstatus,blinkingmeansarming
CommunicationLED,LEDblinkswhenthecommunicationmodeisinaccordancewiththe
hostcomputerprotocol.

6.Connection
Operateasfollowingfiguretoconnectalarmprobe,andconnectaresistance(2K)inseries
connectionatNOcontact.
S=signal,╧=groundwire


7.Protocolsetting
YouwillseeJ1&j2ontheboardasyouopenthebox(thenumber1meansopencircuit,number
0meansshortcircuit)

No.ProtocolJ1J2Note
0DCTRLS00Settingfromaddress0
1RM11001
2W11010
3SE60011Theaddressofchannel1~8is
0,channel9~16is1


VID‐ALARM‐8CH‐COMReferenceManual5

8.SettingthealarmboxID
ThealarmboxIDnumberissetbysettingthe1‐4bitsofDIPswitch.Detailedsettingplease
referstothetablebelow.Thenumber1meanstheDIPswitchsettingshouldbe“ON”,andthe
number0means“OFF”.
Note:theIDnumberisbinarydigit
IDSwitchnumber
1234
00000
10001
20010
30011
40100
50101
60110
70111
81000
91001
101010
111011
121100
131101
141110
151111



VID‐ALARM‐8CH‐COMReferenceManual6

PROTOCOL
Controlcode,whichsendoutfromDVR Commandformat:9600,N,8,1
NO.
FunctionData1Data2Data3Data4 Data5 Data6
Note
FormatStartbitIDCommand Parameter1 Parameter2Checksum
1
Alarm
state
enquiry
E000‐0F3F0000 
2
Relay
state
enquiry
E000‐0F3B0000 
3Output
ON/OFFE000‐0F3DB0‐B7B8‐B15
Bits(0‐15)isthe
relaycontrolbitsof
1‐16channel,1=ON,
0=OFF
Data send back
No.FunctionData1Data2Data3Data4 Data5 Note
1Alarmstate
sendback
F000‐0FD0A0‐A7 A8‐A15 A(0‐15)iscorrespondingtoalarm
inputs1‐16,1=alarm,0=dis‐alarm
2Relaystate
sendback
F000‐0FD2A0‐A7 A8‐A15 A(0‐15)iscorrespondingtooutputs
1‐16,1=ON,0=OFF
Note:
1.Thedata4&data5ofthisalarmboxis0


NOTES:
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________

VID‐ALARM‐8CH‐COMReferenceManual7

TechnicalSupport
FordifficultiesusingthisunitpleasecontactAventuratechnicalsupportat631‐300‐4000ortoll‐freeat
1‐877‐707‐9600.Onlinesupportisavailableatwww.AventuraCCTV.comoremail
[email protected]
WhencontactingtechnicalsupportbecertaintohavefulldetailsaboutyourAventuraproducts
available,includingmodelandinvoicenumbers.
Service
AnyservicerequiredbythisunitshouldbeperformedbyAventuraorauthorizedservicepersonnel.
Unauthorizedservicemayinvalidatewarrantiesorserviceagreements.Someservicemayrequire
equipmenttobereturnedtoAventura’sofficesforevaluationandrepair.Becertaintofollowproper
packingandshippinginstructionsforallequipmenttopreventdamageduringtransport.