Avenview Sw-hbt4k-c6-4x4e User manual

VIDEO WALLS VIDEO PROCESSORS

VIDEO MATRIX SWITCHES

EXTENDERS SPLITTERS WIRELESS

CABLES & ACCESSORIES

AV Connectivity, Distribution And Beyond...

The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or

warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications

and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted

by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any

express or implied warranty, relating to its products are is strictly prohibited.

Control Commands

Model #: SW-HBT4K-C6-4X4E

www.avenview.com Page 1

SECTION 1: COMMAND PROTOCOL FORMAT (RS-232 SERIAL PORT)

1. SERIAL PORT SETTING

- Baud Rate: 19200 bps

- Data Bit: 8 bits

- Parity: None

- Flow Control: None

- Stop Bit: 1

RS-232 Wiring (Cross Cable Connection)

Remote Controller(PC)

SW-HBT-4K-4X4E

PIN Assignment PIN De ﬁnition

1 NC 1 NC

2 TxD 2 RxD

3 RxD 3 TxD

4 NC 4 NC

5 GND 5 GND

6 NC 6 NC

7 NC 7 NC

8 NC 8 NC

9 NC 9 NC

www.avenview.com Page 2

2. RS-232 & TELNET COMMANDS

All commands will be not executed unless followed with a carriage return (0x0D) and commands are case sensitive.

Command Active

A1~A4Switch Output A to 1~4

B1~B4Switch Output B to 1~4

C1~C4Switch Output C to 1~4

D1~D4Switch Output D to 1~4

AB...1~AB...4Switch Output A B C D... to 1~4 at the same time

Setting IP. SubNet. GateWay (Static IP)

P0 Power OFF

P1Power ON

I1~I4Switch all the Output to 1~4

ST Display the current matrix status and F/W version

RS System Reset to H4

EM Setting EDID MODE. 1-STD 2-TV

UARTBAUD1~4

UARTSW1~4 Switch output’s UART to A~D and allow Matrix to send commands to Receiver’s

connected RS-232 device.

SETIP <IP> <SubNet> <GW>

RSTIP IP Configuration Was Reset To Factory Defaults <DHCP>

IPCONFIG Display the Current IP Config

UARTBAUD? Display all the output's UART baud

UARTSW? Display the UART switching state

STORE 01~04 Store current I/O position (01~04)

PRESET 01~04 Recall the store I/O Position (01~04)

SHOW 01~04 Show current port's I/O position (01~04)

NAME N1 N2 Name the stored port N1(01~04) no more than 8 charactors, N2 (ABCDEFGH)

?Display all the available commands

Quit Exit (for telnet only)

UARTSW0 Switch output's UART to MCU. Restoring RS-232 control to the Receiver output back to

Matrix.

Set output A~D’s uart baud rate from 1~6

1: 9600bps

2: 14400bps

3: 19200bps

4: 38400bps

5: 57600bps

6: 115200bps

www.avenview.com Page 3

3.TELNET CONTROL

Using TCP/IP protocol, sent to Port 23 for Telnet communication.

The user can confirm from the OSD menu or through RS-232 command to check Telnet connection behavior.

To use the telnet control, please ensure that both the Matrix (via the 'LAN /CONTROL' port) and the PC/Laptop

are connected to the active networks not directly connected.

To access the telnet control in Windows 7, click on the 'Start' menu and type "cmd" in the Search field then press

enter. Under Windows XP go to the 'Start' menu and click on "Run", type "cmd" with then press enter.

Under Mac OS X, go to Go→Applications→Utilities→Terminal See below for reference.

www.avenview.com Page 4

In the CMD window proceed to type "telnet", then the IP address of the unit and "23", then hit enter/return.

Note: The IP address of the Matrix can be displayed on the device's LCM monitor by pressing the Menu button

twice.

After connecting to the Matrix Switcher via IP address. Type "HELP" to preview the list of commands available.

Type “IPCONFIG” To confirm all IP configurations.

To RESET the IP ADDRESS; type “RSTIP” /To SET a STATIC IP, type”SETIP”

(For a full list of commands, see Section 1.3).

Note:

Commands will not be executed unless followed by a carriage return. Commands are case-insensitive. If the IP is

changed then the IP Address required for Telnet access will also change accordingly.

www.avenview.com Page 5

4.WEB GUI CONTROL

On a PC/Laptop that is connected to the same active network as the Matrix, open a web browser and

type device's IP address on the web address entry bar. The browser will display the device's status,

control and User setting pages.

Click on the 'Control' tab to control power, input/output ports, EDID and reset mode

www.avenview.com Page 6

Clicking on the 'User Setting' tab allows you to reset the IP configuration. The system will ask for a reboot

of the device every time any of the settings are changed. The IP address needed to access the Web GUI

control will also need to be changed accordingly on the web address entry bar.

TECHNICAL SUPPORT

Disclaimer

While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of

Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this

documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages

in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.

Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.

With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but