Avenview W-HDM3D-100-SET User manual

VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
CABLES & ACCESSORIES
AV Connectivity, Distribution And Beyond...
Wireless 60GHz HDMI Extender Set with
3D and Full HD Video Support
© 2013 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims
any express or implied warranty, relating to its products of Avenview Inc. is strictly prohibited.
Model #: W-HDM3D-100-SET

Military Residential
Medical Aviation
Education Industrial
Coroprate House Of Worship
www.avenview.com
Product Application & Market Sectors

www.avenview.com Page 3
TABLE OF CONTENTS
1. GETTING STARTED ..........................................................................................................................1
1. GETTING STARTED ..........................................................................................................................2
1.1 IMPORTANT SAFEGUARDS..............................................................................................................2
1.2 SAFETY INSTRUCTIONS ..................................................................................................................2
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ........................... 3
2. INTRODUCTION ..............................................................................................................................4
2.1 PACKAGE CONTENTS .....................................................................................................................4
2.2 BEFORE INSTALLATION...................................................................................................................6
3. INSTALLATION..................................................................................................................................7
4. GENERAL TROUBLESHOOTING.....................................................................................................8
5. SPECIFICATIONS.............................................................................................................................10
5.1 DVI CONVERTER SCALER..............................................................................................................11
5.2 SIGNAL PIN ASSIGNMENT.............................................................................................................12
5.3 INPUT TIMING ................................................................................................................................13
5.4 AUDIO FORMAT..............................................................................................................................13
5.5 WIRELESS VIDEO AREA NETWORK (WVAN) ...............................................................................14
5.6 CONFIGURATION –MULTIPLE AND SINGLE...............................................................................14
5.7 CONFIGURATION –MULTIPLE AND SINGLE...............................................................................15
5.8 QUICK STARTUP.............................................................................................................................16
5.9 INSTALLATION GUIDE ..................................................................................................................17
Monitor Mount Option .....................................................................................................................17
Wall Mount Option ...........................................................................................................................17
Monitor Mount Option .....................................................................................................................17
Wall Mount Option ...........................................................................................................................17
5.10 SETUP GUIDE .................................................................................................................................18
5.11.1 DVI-VIDEOWALL-12X Front Panel.......................................................................................19
6. MAINTENANCE OF QUALITY OF SERVICE ................................................................................21
6.1 Design Characteristics: Interference from other W-HDM3D-100 Devices ...............................21
6.2 Design Characteristics: Accommodation of Diminished Video Signal Quality ............................... 21
7. REGULATORY..................................................................................................................................22

www.avenview.com Page 1
SECTION 1: GETTING STARTED
The following symbols appear on the product. You can find its labeling, or the product
Symbol Definition Symbol Definition
V~ AC Voltage. OSwitches on power.
ISwitches off power. Contained spare fuse.
Dangerous : High Voltage Consult accompanying
documents.
Indicates protective earth
ground. Serial Number.
Indicates top-bottom
direction. Fragile.
Do not get wet. Maximum stacking
Medical Equipment is in accordance with UL 60601-1 and CAN/CSA C22.2
No.601.1 in regards to electric shock, fire hazards, and mechanical hazard.
Indicates proof of conformity to applicable European Economic Community
Council directives and to harmonized standards published in the official
journal of the European Communities
Tested to comply with FCC Class B standard.
This symbol indicates that the waste of electronic equipment must not be
disposed as unsorted municipal waste and must be collected separately. Please
contact the manufacturer or other authorized disposal company to
Decommission your equipment.
1. GETTING STARTED

www.avenview.com Page 2
SECTION 1: GETTING STARTED
1.1 IMPORTANT SAFEGUARDS
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
•Any product, on which the serial number has been defaced, modified or removed.
•Damage, deterioration or malfunction resulting from:
•Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
•Repair or attempted repair by anyone not authorized by us.
•Any damage of the product due to shipment.
•Removal or installation of the product.
•Causes external to the product, such as electric power fluctuation or failure.
•Use of supplies or parts not meeting our specifications.
•Normal wear and tear.
•Any other causes which does not relate to a product defect.
•Removal, installation, and set-up service charges.
1.2 SAFETY INSTRUCTIONS
The Avenview W-HDM3D-100-SET, HDMI Extender over WIFI has been tested for conformity to safety regulations and
requirements, and has been certified for international use. However, like all electronic equipment’s, the W-HDM3D-100-SET
should be used with care. Read the following safety instructions to protect yourself from possible injury and to minimize the risk
of damage to the unit.
!Do not dismantle the housing or modify the module.
!Dismantling the housing or modifying the module may result in electrical shock or burn.
!Refer all servicing to qualified service personnel.
!Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage
or other hazards
!Keep the module away from liquids.
!Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on
to the housing, unplug the module immediately.
!Have the module checked by a qualified service engineer before using it again.
!Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
1. GETTING STARTED

www.avenview.com Page 3
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against interference. This system can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, it may interfere with other radio communications
equipment. There is no guarantee that interference will not occur in a particular installation. If this equipment is found to cause
harmful interference to radio or television
reception, the user is encouraged to try to correct the interference by carrying out one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the distance between this system and the subject of interference.
3. Plug this system into an outlet on a different electrical circuit than \that to which the subject of interference is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Warning symbols Description
ONLY USE THE PROVIDED POWER CABLE OR POWER
ADAPTER SUPPLIED. DO NOT TAMPER WITH THE
ELECTRICAL PARTS. THIS MAY RESULT IN ELECTRICAL
SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO WILL
VOID THE WARRANTY AND CONTINUED USE OF THE
PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON A
SURFACE, IT SHOULD BE IN A GROUNDED ENVIROMENT.

www.avenview.com Page 4
2. INTRODUCTION
Avenview W-HDM3D-100, our 60 GHz wireless HD transmitter/receiver, provides an easy and flexible solution to wireless
communications. This system supports HD video, 1080p/60Hz, plus new 3D video formats generated by HDMI 1.4a. Both CEC
and non-CEC enabled devices are compatible with our W-HDM3D-100 wireless system.60 Ghz reliability
2.1 PACKAGE CONTENTS
1. Wireless HD transmitter (W-HDM3D-S-100) unit
2. Wireless HD receiver (W-HDM3D-R-100) unit
3. User Guide
4. HDMI to DVI-D cables
5. Medical grade power cord
6. Medical power adaptor (5V/2A)
For wall mounting:
7. 1x Bracket (Standard type for installing) and screw
For monitor bezel installation:
8. Bracket (Medical type for installing) and screw
9. DC splitter
10. DVI to HDMI signal converter/scaler (CW-HDMDVI-100)
11. HDMI to HDMI cable
12. Cable guides and extra screws
13. Power cable for CW-PS-HDMSP-100

www.avenview.com Page 5
Before you start the installation of the Extender/Splitter, please check the package contents.
1 W-HDM3D-S-100 (Transmitter Unit) X 1
2 W-HDM3D-R-100 (Receiver Unit) X1
3User Manual X 1
4Medical grade power code & adaptor (5V/2A) X2
5HDMI to DVI-D cables X 2
6Bracket (Standard type for installing) and screw X 1
7Bracket (Medical type for installing) and screw X 1
Do not use any other cable or accessory that are not provided

www.avenview.com Page 6
2.2 BEFORE INSTALLATION
•A bad connection may cause fault.
•Do not stack and locate close to other equipment
•Be sure to contact an supplier, when installing your system in a Location with the Heavy dust, high or low temperatures,
high humidity, chemical substance.
•Failure to do so may cause a serious damage to your system.
•Before connecting the AC power cord to the system, make sure the voltage designation is correct;
•Never use this system with a damaged power cord;
•Be sure to hold the plug, not the cord, when disconnecting from an electric socket;
•Install this system in a location with low humidity and minimum dust;
•To prevent overheating, product vents should not be blocked or covered;
•Do not attempt to disassemble or modify your product;
•Only authorized personnel should perform service;
•Never insert anything metallic into the product vents;
•Do not touch signal input, signal output or other connectors, and the patient simultaneously.

www.avenview.com Page 7
3. INSTALLATION
This product is composed of a Transmitter and a Receiver. The Transmitter should be connected to the source (Computer’s
HDMI Port) and the Receiver should be connected the HDMI Port of the digital display device (Monitor).
1. Avenview W-HDM3D-100 Transmitter / Receiver are designed to be no more than 33 feet (10 meters) apart.
2. Be on the same level (one should not be higher than the other).
3. Not be in a confined location (i.e. A cabinet or an enclosed shelf).
4. Reposition the Rx and Tx, allowing as many open paths to the receiver as possible.
5. Face each other.

www.avenview.com Page 8
4. GENERAL TROUBLESHOOTING
PROBLEM POSSIBLE SOLUTION
NO VIDEO OR
AUDIO
•• If the power LEDs on the transmitter and receiver are blinking, the adapters are
not linked. See “Receiver will not link to Transmitter” troubleshooting steps above.
•• If the power LED on the transmitter and receiver are solid (not blinking), the adapters
are linked such that video and audio sent into the transmitter should be output from
the receiver. Therefore, the display/monitor may not be set to the HDMI input jack
that the WIS1000 Receiver unit is connected to. Refer to the documentation provided
with your display/monitor for information on how to select the correct input.
•• The source component is not powered on and/or does not have the HDMI output
en-bled. Refer to the documentation provided with your source component for
information on switching that component to the HDMI output.
•• The transmitter is set to the incorrect HDMI port. Switch the transmitter to the
correct HDMI port for the component you want to view with the HDMI/WVAN
switch on the back of the transmitter.
•• Make sure that you are using high speed certified HDMI cables for all connections
and that all cable connections are secure. We recommend high quality HDMI cables.
RECEIVER WILL
NOT LINK TO
TRANSMITTER
•The power LED on the transmitter and the receiver will blink continuously while the
trans¬mitter is not linked to the receiver. This can be caused by the receiver being located
too far away from the transmitter. The maximum non-line-of-sight range is approximately
33ft. (10m).
•Try re-positioning the transmitter and receiver units so they are within the specified
operating range. First try to get the units to link with each other at 3 ft. (1 m) (to prove
that they are working properly with your equipment). Then try moving them further
apart to the desired locations.
•Materials may be blocking the 60 GHz radio frequency beam from the transmitter to
the receiver. This beam can pass through many cabinet materials such as glass and wood
(depending on thickness and density of the materials), but it cannot pass through doors,
shelves, or components that are made of metal.
•Try positioning the transmitter and receiver so that they are not blocked by metal.
•Either the receiver or transmitter is not powered on. Be sure the AC adapter is securely
connected and each unit is powered on correctly.
•Power cycle both the transmitter and receiver by unplugging then plugging them back in.

www.avenview.com Page 9
WARNING
Do not put heavy object on top of the W-HDM3D-100.
It may cause product malfunction.
Put the product on even and stable location.
If the product falls down or dropped, it may get damaged.
Keep away from high temperature (over 50°C), low temperature
(under 0°C) or high humidity. It may cause a fire and injury
by electrical shock.
Use DC power adapter with correct specification.
Otherwise it may cause fire.
Use the multimode (50/125um) optical fiber.
Do not view directly laser module of transmitter or the end of the other
side of optical cable connected to transmitter with optical instrument.
Do not twist or pull by force either ends of the optical cable. It can cause
malfunction. Minimum bending diameter is 45mm
Thank You.

www.avenview.com Page 10
5. SPECIFICATIONS
ITEM DESCRIPTION
UNITS W-HDM3D-S-100 W-HDM3D-R-100
UNIT DESCRIPTION HDMI WIFI Transmitter HDMI WIFI Receiver
HDMI COMPLIANCE HDMI Interface HDMI
INPUT & OUTPUT SIGNAL Yes
ANTENNA TYPE 32 Antenna Array (Integrate Ceramic)
VIDEO BANDWIDTH 4Gbps over-the-air data transfer rate
RAGE 10 meters in-room usage
AV PORT Transmitter : 1 Port (CEC pass through) Receiver : 1 Port (CEC pass through)
HDMI CONNECTOR HDMI Female Connector
DIMENSIONS (L X W X H) 6.5”x 3.4”x 2”
WEIGHT 0.5 lbs
Environmental
OPERATING TEMPERATURE 0 ~ 40 ˚C (32 ~ 104˚ F) ambient temperature
STORAGE TEMPERATURE -4˚ ~ 158˚F (-20˚ ~ 70˚C)
RELATIVE HUMIDITY 10~90% RH (no condensation)

www.avenview.com Page 11
5.1 DVI CONVERTER SCALER
Improve wireless reliability and video connectivity with the CW-HDMDVI-100
The CW-HDMDVI-100 is a DVI converter and scaler created to provide a “clean” output signal complying with industry
standards. It allows the user to upscale a lower resolution to HD. Some medical device manufacturers prefer not to use the
normal standardized timings for HD resolutions. If this is the case with your intended source, then the W-HDM3D-100-SET will
be unable to successfully transmit video from your source to the desired display. In this situation, the CW-HDMDVI-100 scalar/
converter can be used to regulate the signal from the source into a standardized video signal that the W-HDM3D-100-SET
system can understand.
The CW-HDMDVI-100 is designed to be used with, and easily connected to, AVENVIEW wireless W-HDM3D-100 product.

www.avenview.com Page 12
5.2 SIGNAL PIN ASSIGNMENT
TRANSMITTER
Pin 1 T.M.D.S. Data2+ Pin 11 T.M.D.S. Clock Shield
Pin 2 T.M.D.S. Data2 Shield Pin 12 T.M.D.S. Clock-
Pin 3 T.M.D.S. Data2 - Pin 13 NC
Pin 4 T.M.D.S. Data1 + Pin 14 NC
Pin 5 T.M.D.S. Data1 Shield Pin 15 DDC SCL
Pin 6 T.M.D.S. Data1- Pin 16 DDC SDA
Pin 7 T.M.D.S. Data0 + Pin 17 DDC Ground
Pin 8 T.M.D.S. Data0 Shield Pin 18 +5V Power
Pin 9 T.M.D.S. Data0 - Pin 19 Hot Plug Detect
Pin 10 T.M.D.S. Clock+
RECEIVER
Pin 1 T.M.D.S. Data2+ Pin 11 T.M.D.S. Clock Shield
Pin 2 T.M.D.S. Data2 Shield Pin 12 T.M.D.S. Clock-
Pin 3 T.M.D.S. Data2 - Pin 13 NC
Pin 4 T.M.D.S. Data1 + Pin 14 NC
Pin 5 T.M.D.S. Data1 Shield Pin 15 DDC SCL
Pin 6 T.M.D.S. Data1- Pin 16 DDC SDA
Pin 7 T.M.D.S. Data0 + Pin 17 DDC Ground
Pin 8 T.M.D.S. Data0 Shield Pin 18 +5V Power
Pin 9 T.M.D.S. Data0 - Pin 19 Hot Plug Detect
Pin 10 T.M.D.S. Clock+

www.avenview.com Page 13
5.3 INPUT TIMING
Video Format Vertical Refresh Color Space Sampling Bits/Pixel
420p 59.94/60Hz YCbCr 4:2:2 24/30-bits
4:4:4 24/30-bits
RGB 4:4:4 24/30-bits
720p
50Hz YCbCr 4:2:2 24/30-bits
59.94/60Hz 4:4:4 24/30-bits
RGB 4:4:4 24/30-bits
1080i
50Hz YCbCr 4:2:2 24/30-bits
59.94/60Hz 4:4:4 24/30-bits
RGB 4:4:4 24/30-bits
1080p 23.976/24Hz YCbCr 4:2:2 24/30-bits
50Hz 4:4:4 24/30-bits
59.94/60Hz RGB 4:4:4 24/30-bits
VGA 60Hz RGB 4:4:4 24/30-bits
WVGA 60Hz RGB 4:4:4 24/30-bits
SVGA 60Hz RGB 4:4:4 24/30-bits
SXGA 60Hz RGB 4:4:4 24/30-bits
VGA 60Hz RGB 4:4:4 24/30-bits
WSXGA+ 60Hz RGB 4:4:4 24/30-bits
5.4 AUDIO FORMAT
Audio up to 2-ch. 24-bit 192 kHz LPCM and 8-ch. 24-bit 96 kHz LPCM as well as surround sound audio (Dolby Digital, DTS)
is supported.
Audio
Multiples of Fs
Audio Sample Rate
LPCM 2/6/8-channels
LPCM 2-channel
DTS & Dolby Digital
2/6 channels
32 kHz 44.1 kHz 48 kHz 88.2 kHz 96 kHz 176.4 kHz 192 kHz
128 4.096 5.645 6.144 11.29 12.288 22.579 24.576
256 8.192 11.29 12.288 22.579 24.576 45.158 49.152

www.avenview.com Page 14
5.5 WIRELESS VIDEO AREA NETWORK (WVAN)
The 60GHz W-HDM3D-100 transmitter and receiver provides Wireless Video Area Network (WVAN) connectivity. A WVAN
network allows a TX to selectively synchronize with up to six Rx. In turn, a Rx to selectively synchronize with up to six TX.
Several combinations can be made.
5.6 CONFIGURATION –MULTIPLE AND SINGLE
In the diagram below, they are 5 TX and 5 RX transmitting and receiving video simultaneously.
- Each TX has synchronized with RX on its own channel.
- When the Wireless Transmitter is first powered on, it searches for a Wireless receiver via WVAN.
- When the TX synchronizes with RX, the WVAN ID of the RX is stored in memory, of the TX, as a preferred ID.
- The next time the TX is powered on, it will search for the preferred WVAN ID of the RX.
- Switching between TX and RX is done by pushing and holding down the “Switch” button for 3 seconds or until the LED
flashes. The TX will connect to the next available Rx in the network.

www.avenview.com Page 15
5.7 CONFIGURATION –MULTIPLE AND SINGLE
In the diagram below, there is 1 TX and 6 RX devices CONNECTED in a single room. For example with this scenario, the TX
has the option to synchronize with any one of the 6 Rx on its WVAN.
-Switching between TX and RX is done by pushing and holding down the “Switch “button for 3 seconds or until the
LED flashes. The TX will connect to the next available Rx in the network

www.avenview.com Page 16
5.8 QUICK STARTUP
LED INDICATORS
LED COLOR BEHAVIOR
POWER GREEN BLINKING Tx and Rx have not found each other yet
ON Devices connected.
OFF The LED will darken when the power switch is turned off.
CONFIGURATION
HDMI Connect the HDMI end of the cable to the HDMI port on the Rx/TX.
Connect and the DVI end to the medical equipment and/or monitor
DC-IN Connects to the power adapter or DC splitter 5volt output
POWER
SWITCH Switch used to turn on/off the Tx/Rx.
RE-SYNC Please press to sync with receiver

www.avenview.com Page 17
5.9 INSTALLATION GUIDE
Monitor Mount Option
1. Choose a position 1 or 2.
2. Remove two mounting screws, place the bracket in position and reinstall the screws.
3. Connect DVI to HDMI cable between the monitor and W-HDM3D-100 Rx.
4. Connect DC splitter between the DC power adapter and monitor.
5. Connect the 5volt cable of the DC splitter to the W-HDM3D-100 Rx.
6. Align the cables
Wall Mount Option
1. Position the wall mount bracket on the wall and mark the screw locations.
2. Insert the two screws into the wall.
3. Slide the Rx or Tx onto the bracket and lock in place with a screw from the underside.
4. Align the bracket holes with the wall screws push and slide down into position.
OR
Receiver Installation
Monitor Mount Option
Wall Mount Option