Avery Dennison AP5.4 Gen II Troubleshooting guide

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL
AP5.4 Gen II – AP5.6
Info Printouts & Parameters
General Information ...................................... 5
Important setting instructions .................... 5
Area of application .................................... 5
Operating the parameter menu ..................... 7
Example .................................................... 7
Parameter Menu ...................................... 8
Overview Parameter Menus ......................... 9
Understanding the Parameter Overviews . 9
AP5.4 Parameter .................................... 10
Alphabetical Parameter List ........................ 13
PRINT INFO
Printer status........................................... 16
Memory status ......................................... 18
Font status .............................................. 19
Flashdata status...................................... 22
Service Status......................................... 23
Dottest endless ....................................... 24
Dottest punched...................................... 24
Reference label....................................... 25
RFID Status............................................. 26
PRINT PARAMETERS
Print speed.............................................. 27
Feed speed ............................................ 27
Material type............................................ 28
Material length......................................... 28
Material width.......................................... 28
Print direction.......................................... 29
Punch offset ............................................ 30
Bar code multip....................................... 30
Tradit. Imaging ....................................... 31
UPC plain-copy....................................... 31
EAN Readline.......................................... 31
EAN sep. lines......................................... 32
Rotated Barcodes ................................... 32
Dispenseposition..................................... 32
Cut mode................................................. 33
Cut speed................................................ 35
Cut position............................................. 35
Double cut............................................... 35
Rewind direction ...................................... 36
X - Printadjust.......................................... 36
Y – Printadjust ......................................... 36
Punch mode............................................. 37
Punch level.............................................. 37
INTERFACE PARA
> EASYPLUGINTERPR
Interface................................................... 38
Spooler mode .......................................... 38
Printer ID No............................................ 39
Spooler size............................................. 39
Offline mode ............................................ 39
Interface delay......................................... 39
> COM1 PORT
Baud rate................................................. 40
No. of data bits......................................... 40
Parity........................................................ 40
Stop bits................................................... 40
Data synch............................................... 41
Frame error.............................................. 41
> COM3 PORT
Baud rate................................................. 41
No. of data bits......................................... 41
Parity........................................................ 41
Stop bits................................................... 42
Data synch............................................... 42
Frame error.............................................. 42
Serial Port Mode...................................... 42
> COM4 PORT
Baud rate................................................. 43
No. of data bits......................................... 43
Parity........................................................ 43
Stop bits................................................... 43
Data synch............................................... 43
Frame error.............................................. 43
> USB
USB select............................................... 44
> NETWORK PARAM.
IP addressassign..................................... 44
IP address................................................ 44

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL
AP5.4 Gen II – AP5.6
Net mask................................................. 44
Gateway address .................................... 45
Port address............................................ 45
Ethernet speed........................................ 45
MAC address .......................................... 45
SNMP agent............................................ 45
SNMP password ..................................... 45
FTP server .............................................. 46
FTP password......................................... 46
WEB server............................................. 47
WEB display refr ..................................... 48
WEB admin passw.................................. 48
WEB supervisor p. .................................. 48
Time client............................................... 49
Time server IP......................................... 49
Sync. Interval .......................................... 49
DHCP host name.................................... 50
> OPTIONS
RFID Option............................................ 50
StandAlone Input..................................... 50
> DRIVEASSIGNMENT
Drive C.................................................... 51
Drive D.................................................... 51
SYSTEM PARAMETERS
Foil end warning...................................... 52
Foil warn stop.......................................... 52
Print Interpret. ......................................... 52
Character sets......................................... 53
Character filter......................................... 54
Light sens. type....................................... 54
Head-sensor dist..................................... 54
Sens. punch-LS....................................... 55
Foil mode ................................................ 55
Turn-on mode.......................................... 55
Error reprint............................................. 55
EasyPlug error ........................................ 56
Single job mode ...................................... 56
Head resistance...................................... 56
Temp. reduction...................................... 57
Thin line emphas..................................... 57
Voltage offset.......................................... 58
Miss. label tol. ......................................... 58
Gap detect mode..................................... 58
Periph. device.......................................... 59
Singlestartquant....................................... 59
External signal......................................... 59
Start print mode....................................... 60
Print contrast............................................ 60
Ram disk size .......................................... 60
Font downl. area...................................... 61
Free store size......................................... 62
Print info mode......................................... 62
Reprint function........................................ 62
Language................................................. 63
Keyboard ................................................. 63
Access authoriz. ...................................... 63
Realtime clock ......................................... 65
I/O BOARD
Start print mode....................................... 66
Reprint Signal.......................................... 66
Feed input................................................ 67
Pause input.............................................. 67
Error output.............................................. 67
Error Polarity............................................ 68
Status output ........................................... 68
Status polarity.......................................... 68
End print mode ........................................ 69
DISPENSER PARA
Dispense Mode........................................ 70
Dispenseposition ..................................... 71
Display mode ...........................................72
Dispense counter..................................... 72
Application mode..................................... 72
Start source ............................................. 73
Calibration mode...................................... 73
Start offset ............................................... 73
Start error stop......................................... 74
Product length.......................................... 74
Current mode........................................... 74
Min. rew. current...................................... 75
Max. rew. current..................................... 75
Start rew. current..................................... 76
Start cur. len. ........................................... 76

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL
AP5.4 Gen II – AP5.6
Pullback current ...................................... 76
Back diameter......................................... 77
Brake current........................................... 77
Brake diameter........................................ 77
REWINDER PARA
Rewind direction...................................... 78
Current mode.......................................... 78
Min. rew. current ..................................... 78
Max rew. current ..................................... 78
Start rew. curr.......................................... 78
Start cur. len............................................ 79
Pullback current ...................................... 79
Back diameter......................................... 79
Brake current........................................... 79
Break diameter........................................ 79
MLI PARAMETERS
Darkness................................................. 80
Control Prefix .......................................... 80
Format Prefix........................................... 80
Delimiter Char......................................... 81
Label Top................................................ 81
Left Position ............................................ 81
Manual Calibrate..................................... 81
Resolution............................................... 81
Error Indication........................................ 82
Error Checking........................................ 82
Image Save Path..................................... 82
Command ^PR....................................... 82
Command ^MT....................................... 82
Label Invert ............................................. 83
Command ^JM....................................... 83
Command ^MD/~SD............................... 83
SPECIAL FUNCTION
Printer type.............................................. 84
Default Values......................................... 84
Command sequence............................... 84
Delete job................................................ 84
Delete spooler......................................... 85
Factory settings....................................... 85
Store Parameters.................................... 85
Store Diagnosis ....................................... 86
Data blocks del........................................ 86
EasyPl. file log......................................... 87
Log files delete......................................... 87
RFID stat. del........................................... 87
SERVICE FUNCTION
Service..................................................... 88
Head exchange........................................ 88
Roller exchange....................................... 88
Cutter exchange ......................................89
Serv. data reset ....................................... 89
EasyPlug monitor..................................... 89
EP Monitor Mode..................................... 90
Sensor adjust........................................... 90
Sensor test .............................................. 90
Cutter test................................................ 90
Matend tolerance..................................... 91
Feedadjust label ...................................... 91
Feed adjust.............................................. 91
Punch y calibr.......................................... 91
Memory card test..................................... 92
Send test ................................................. 93
Receive test............................................. 94
Rewinder adjust....................................... 95
Printtest.................................................... 95
SERVICE DATA
> MODULE FW VERS.
System version........................................ 96
System revision ....................................... 96
System date............................................. 96
Bootloader ............................................... 96
uMon........................................................ 96
Peripheraldriver ....................................... 96
Intern. rewinder........................................ 97
> OPERATION DATA
Serv. operations....................................... 97
Headnumber............................................ 97
Roll number ............................................. 97
Cutter number.......................................... 97
Head run length....................................... 98
Roll run length.......................................... 98

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL
AP5.4 Gen II – AP5.6
Cuts on knife........................................... 98
Tot. mat. length....................................... 98
Tot. foil length.......................................... 98
Total cuts................................................. 98
Head strobes........................................... 99
Head temperature................................... 99
Foil diameter ........................................... 99
Dispensing cycl....................................... 99
Operation time......................................... 99
> POWERSUPPLYDATA
Type...................................................... 100
PS temperature..................................... 100
> CPU BOARD DATA
CPU identifier........................................ 100
PCB revision ......................................... 100
FPGA version........................................ 100
MAC address ........................................ 100
Serial number ........................................ 100
Production date...................................... 101
PCB part number................................... 101
Board part numb.................................... 101
Manufacturer.......................................... 101
Work place............................................. 101
Company name ..................................... 101
> DISPLAY DATA
Display version ...................................... 102
Display SerialNr..................................... 102
> MEMORY DATA
Ram memory size.................................. 102
Flash mem size...................................... 102
SD card.................................................. 103
Space for Jobs....................................... 103
Max. Labellength ................................... 103
Default values........................................ 103

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
5
General Information
Important setting instructions
Starting in offline mode, you get to the parameter menu by pressing the prog
button. There you can set/alter the different parameters of the printer and ac-
tivate/deactivate options.
Many Parameters provide a range within the setting can be changed with a
standard step width. By this step width, the setting is changed, if the Cut-(Ap-
ply-) or Feed button is pressed once.
¯The step width can be increased ten times, if the Online button is pressed
simultaneously (Cut+Online or Feed+Online).
¯Wait at least 10 seconds between switching the device off and on again,
otherwise any modified parameter settings are not saved.
¯With some parameters, false settings can result in the device being
damaged (e. g. if the print head temperature is too high). Data and/or print
orders are also deleted during formatting and with other settings.
¯Pay attention to the corresponding notes in the following description to
ensure that no damage occurs!
Area of application
The description counts for all devices listed in the headline of this document.
All status printouts and parameters are described in the same order as they
may appear in the parameter menu of the respective printer.
¯Not all of the parameters appear in each of the listed printers!
At the beginning of each parameter description can be found information
about the availability of the parameter:
Fig. 1: At the beginning of each parameter description, the availability of the parameter is
specified: Between the two lines is a list of the concerned printer types; the remark
below (arrow) quotes further conditions.
If a parameter appears in the menu of a certain printer type or not, depends
on the following, which can be read from this bar:
yThe printer type:
Printers, which have the parameter available in the parameter menu, are
listed between the lines. Example (see fig. 1): AP 5.4, AP5.6.
yThe configuration with options and/or certain parameter settings:
Example (see fig. 1): The parameter only appears in the menuof an AP5.4/
5.6, if the device is equipped with an board. If the remark is not assigned to
a special printer type, it is valid for all listed printers.
Firmware This description applies to all printers which are equipped with a firmware
version 7.34 Pre 4081 for AP5.4/AP5.6.
AP5.4 AP5.6
¯Only with installed I/O board.

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
6
PThe paragraph „Overview Parameter Menues“ in this topic section contains
an overview of all available parameters of the respective printer.

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
7
Operating the parameter menu
The illustrations on the following pages clarifie the operating principle of the
parameter menu. The return path shown on the left of the screen, called up
using the Prog. button, also applies for parameters in the middle of the
screen.
Setting values The setting of a parameter always follows this scheme:
1. Select the parameter.
2. Press the Online button.
3. Set the parameter to the intended value by pressing the Cut or Feed button.
4. Confirm by pressing the Online button.
Example
Setting the parameter PRINT PARAMETERS > Material type to punched material.
1. Press prog button.
2. Press prog button.
3. Press cut button.
4. Press online button.
5. Press cut button repeatedly, until the following is displayed:
6. Press feed button.
7. Press online button.
8. Press prog button 2x.
OFFLINE 0 JOBS Initial state: off-line mode
PRINT INFO
PRINT PARAMETERS
PRINT PARAMETERS
Print speed First parameter in the PRINT PARAMETERS menu.
Material type
Endless
Material type
Punched Setting the parameter to the intended value by pressing the Cut or Feed button.
PRINT PARAMETERS
Material type Confirm with Online button.
OFFLINE 0 JOBS "Way back" by pressing the Prog button.

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
8
Parameter Menu
Fig. 1: Guideline through the parameter menu. Start into it by pressing the Prog button in
off-line mode.
OFFLINE 0 JOBS
ONLINE 0 JOBS
PRINT INFO
PRINT INFO
Printer status
PRINT INFO
Memory status
PRINT PARAMETERS INTERF. PARAM.
PRINT PARAMETERS
Print speed
Print contrast
65 %
Scrolls down through the menu and
selects menu items. Reduces values.
Scrolls up through the menu and
selects menu items. Increases values.
Selects the parameter menu from
offline mode. Returns to previous menu.
Switches between online and offline mode
or confirms menu items, values and
status messages.

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
9
Overview Parameter Menus
Understanding the Parameter Overviews
The charts in the following show all of the parameters implemented in the printer firmware. Some
parameters are only visible in the parameter menu under specific preconditions. These parame-
ters are provided with a gray background and a digit at the right column edge. The digit refers to
a footnote describing the precondition under which the parameter is visible.

1. Only with INTERF.PARAM. > NETWORK PARAM. > WEB Server = „enabled“ 2. Only with BLDC firmware version V4-T36 or higher 3. Only with INTERF.PARAM. > NETWORK PARAM. > Time client = „Enabled“
4. Only with at least one data block stored in the flash memory 5. Only with rewinder 6. Only with cutter 7. Only with „AP5.4 peripheral“ 8. Only if SYSTEM PARAMETERS > Periph. device = „Tear-off edge“ or
„Tear off + sensor“ 10. Only with activated MONARCH LANGUAGE INTERPRETER™ 12. Only if PRINT PARAMETERS > Punch mode = „Manual“ 13. Only in production mode 14. As in 13. or with a setting value
> 0 18. Only with installed RFID option 20. Only if SYSTEM PARAMETERS > Periph. device = „Dispenser“ 21. Only if SYSTEM PARAMETERS > Periph. device = „Int Rewinder“ 22. Only with an activated RFID
option 23. Only with I/O board 24. Not with I/O board 29. Availability depends on device configuration 30. Only with a memory card inserted
03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
10
AP 5.4 Parameters
AP5.4 Parameter
PRINT INFO PRINT PARAMETERS INTERFACE PARA (INTERFACE PARA cont.) (INTERFACE PARA cont.) SYSTEM PARAMETER
Printer status Print speed > EASYPLUGINTERPR Parity > OPTIONS Foil end warning
Memory status Feed speed Interface Stop bits RFID Option Foil warn stop
Font status Material type Spooler mode Data synch. StandAlone Input Print Interpret.
Flashdata status 4 Material length Printer ID No. Frame error Character sets
Service status Material width Spooler size > DRIVEASSIGNMENT Character filter
Dottest endless Print direction Offline mode > USB Drive C Light sens. type
Dottest punched Punch offset Interface delay USB select Drive D Head-sensor dist 13/14
Reference label Bar code Multi. Sens. punch-LS
RFID status 22 Tradit.Imaging 13 > COM1 PORT > NETWORK PARAM. Foil mode
UPC plain-copy Baud rate IP Addressassign Turn-on mode
EAN Readline No. of data bits IP Address Error reprint
EAN sep. lines Parity Net mask EasyPlug errors
Cut mode 6 Stop bits Gateway address Single job mode
Cut position 6 Data synch. Port address Head resistance
Double cut 6 Frame error Ethernet speed Temp. reduction
Rewind direction 5 MAC address Thin line emphas 13
Rotated barcodes > COM3 PORT 23 SNMP agent Voltage offset
Dispenseposition 8 Baud rate 23 SNMP password 13 Miss. label tol.
X – Printadjust No. of data bits 23 FTP server Gap detect mode
Y – Printadjust Parity 23 FTP password 13 Periph. device
Punch mode Stop bits 23 WEB server Singlestartquant
Punch level 12 Data synch. 23 WEB display refr 1 External signal
Serial Port Mode 23 WEB admin passw. 13 Start print mode 24
Frame error 23 WEB supervisor p. 13 Print contrast
Time client Ram disk size
> COM4 PORT Time server IP 3 Font downl. area
Baud rate Sync. intervall 3 Free store size
No. of data bits DHCP host name Print info mode
FW 7.34 Pre 4081

1. Only with INTERF.PARAM. > NETWORK PARAM. > WEB Server = „enabled“ 2. Only with BLDC firmware version V4-T36 or higher 3. Only with INTERF.PARAM. > NETWORK PARAM. > Time client = „Enabled“
4. Only with at least one data block stored in the flash memory 5. Only with rewinder 6. Only with cutter 7. Only with „AP5.4 peripheral“ 8. Only if SYSTEM PARAMETERS > Periph. device = „Tear-off edge“ or
„Tear off + sensor“ 10. Only with activated MONARCH LANGUAGE INTERPRETER™ 12. Only if PRINT PARAMETERS > Punch mode = „Manual“ 13. Only in production mode 14. As in 13. or with a setting value
> 0 18. Only with installed RFID option 20. Only if SYSTEM PARAMETERS > Periph. device = „Dispenser“ 21. Only if SYSTEM PARAMETERS > Periph. device = „Int Rewinder“ 22. Only with an activated RFID
option 23. Only with I/O board 24. Not with I/O board 29. Availability depends on device configuration 30. Only with a memory card inserted
03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
11
AP 5.4 Parameters
(SYSTEM PARAM. cont.) I/O BOARD PARA 23 MLI PARAMETERS 10 DISPENSER PARA 20 REWINDER PARA 21 SPECIAL FUNCTION
Reprint function Start delay 23 Version 10 Dispense Mode 20 Rewind direction 21 Printer type 13
Language Start print mode 23 Darkness 10 Dispenseposition 20 Current mode 13+21 Default values 13
Keyboard Reprint Signal 23 Control Prefix 10 Display mode 20 Min rew. current 13+21 Command sequence 13
Access authoriz. Feed input 23 Format Prefix 10 Dispense counter 20 Max rew. current 13+21 Delete job
Realtime Clock Pause input 23 Delimiter Char 10 Application mode 20 Start rew. curr. 13+21 Delete spooler
Error output 23 Label Top 10 Start source 20 Start cur. len. 13+21 Factory settings
Error polarity 23 Left Position 10 Calibration mode 20 Pullback current 13+21 Store parameters
Status output 23 Manual Calibrate 10 Start offset 20 Back diameter 13+21 Store diagnosis
Status polarity 23 Resolution 10 Start error stop 20 Break current 13+21 EasyPl. file log 30
End print mode 23 Error Indication 10 Product length 20 Break diameter 13+21 Log files delete 30
Error Checking 10 Speed Adaption 20 Data blocks del. 4
305 DPI Scaling 10 Current mode 13+20 RFID stat. del. 22
Image Save Path 10 Min rew. current 13+20
Command ^PR 10 Max rew. current 13+20
Command ^MT 10 Start rew. curr. 13+20
Label Invert 10 Start cur. len. 13+20
Command ^JM 10 Pullback current 13+20
Back diameter 13+20
Break current 13+20
Break diameter 13+20
FW 7.34 Pre 4081

1. Only with INTERF.PARAM. > NETWORK PARAM. > WEB Server = „enabled“ 2. Only with BLDC firmware version V4-T36 or higher 3. Only with INTERF.PARAM. > NETWORK PARAM. > Time client = „Enabled“
4. Only with at least one data block stored in the flash memory 5. Only with rewinder 6. Only with cutter 7. Only with „AP5.4 peripheral“ 8. Only if SYSTEM PARAMETERS > Periph. device = „Tear-off edge“ or
„Tear off + sensor“ 10. Only with activated MONARCH LANGUAGE INTERPRETER™ 12. Only if PRINT PARAMETERS > Punch mode = „Manual“ 13. Only in production mode 14. As in 13. or with a setting value
> 0 18. Only with installed RFID option 20. Only if SYSTEM PARAMETERS > Periph. device = „Dispenser“ 21. Only if SYSTEM PARAMETERS > Periph. device = „Int Rewinder“ 22. Only with an activated RFID
option 23. Only with I/O board 24. Not with I/O board 29. Availability depends on device configuration 30. Only with a memory card inserted
03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
12
AP 5.4 Parameters
SERVICE FUNCTION SERVICE DATA (Service Data cont.)
Service 13 > MODULE FW VERS. > CPU BOARD DATA
Head exchange 13 System version CPU identifier
Roller exchange 13 System revision PCB revision
Cutter exchange 13+6 System date FPGA version
Serv. data reset 13 Bootloader MAC address
EasyPlug monitor 23 uMon Serial number
EP Monitor Mode 13 Peripheraldriver 7 Production date
Sensor adjust 13 Intern. rewinder 21 PCB part number
Sensor test Board part numb.
Cutter test > OPERATION DATA Manufacturer 13
Matend adjust Serv. operations Work place 13
Matend tolerance Headnumber Company name 13
Feedadjust label Roll number
Feed adjust Cutter number 6 > DISPLAY DATA
Punch y calibr. 13 Head run length Display version
Memory card test Roll run length Display SerialNr
Send test Cuts on knife 6
Receive test Tot. mat. length > MEMORY DATA
Rewinder adjust 5 Tot. foil length Ram memory size
Print test Total cuts 6 Flash mem size
Head strobes SD card 30
Head temperature Space for Jobs
Foil diameter Max. Labellength
Operation time Default values
> POWERSUPPLYDATA
Type
PS temperature
FW 7.34 Pre 4081

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
13
Alphabetical Parameter List
Access authoriz.. . . . . . . . . . . 63
Application mode . . . . . . . . . . 72
Back diameter. . . . . . . . . . . . . 77
Back diameter. . . . . . . . . . . . . 79
Bar code multip. . . . . . . . . . . . 30
Baud rate . . . . . . . . . . . . . . . . 40
Baud rate . . . . . . . . . . . . . . . . 41
Baud rate . . . . . . . . . . . . . . . . 43
Board part numb. . . . . . . . . 101
Bootloader . . . . . . . . . . . . . . . 96
Brake current . . . . . . . . . . . . . 77
Brake current . . . . . . . . . . . . . 79
Brake diameter . . . . . . . . . . . . 77
Break diameter . . . . . . . . . . . . 79
Calibration mode. . . . . . . . . . . 73
Character filter . . . . . . . . . . . . 54
Character sets . . . . . . . . . . . . 53
Command ^JM. . . . . . . . . . . . 83
Command ^MT . . . . . . . . . . . 82
Command ^PR . . . . . . . . . . . 82
Command ^MD/~SD. . . . . . . . 83
Command sequence. . . . . . . . 84
Company name . . . . . . . . . 101
Control Prefix . . . . . . . . . . . . . 80
CPU identifier . . . . . . . . . . . 100
Current mode . . . . . . . . . . . . . 74
Current mode . . . . . . . . . . . . . 78
Cut mode . . . . . . . . . . . . . . . . 33
Cut position. . . . . . . . . . . . . . . 35
Cut speed. . . . . . . . . . . . . . . . 35
Cuts on knife. . . . . . . . . . . . . . 98
Cutter exchange. . . . . . . . . . . 89
Cutter number. . . . . . . . . . . . . 97
Cutter test. . . . . . . . . . . . . . . . 90
Darkness. . . . . . . . . . . . . . . . . 80
Data blocks del. . . . . . . . . . . . 86
Data synch.. . . . . . . . . . . . . . . 41
Data synch.. . . . . . . . . . . . . . . 42
Data synch.. . . . . . . . . . . . . . . 43
Default values. . . . . . . . . . . . 103
Default Values . . . . . . . . . . . . 84
Delete job. . . . . . . . . . . . . . . . 84
Delete spooler . . . . . . . . . . . . 85
Delimiter Char . . . . . . . . . . . . 81
DHCP host name. . . . . . . . . . 50
Dispense counter. . . . . . . . . . 72
Dispense Mode . . . . . . . . . . . 70
Dispenseposition . . . . . . . . . . 32
Dispenseposition . . . . . . . . . . 71
Dispensing cycl.. . . . . . . . . . . 99
Display mode . . . . . . . . . . . . . 72
Display SerialNr . . . . . . . . . . 102
Display version. . . . . . . . . . . 102
Dottest endless. . . . . . . . . . . . 24
Dottest punched. . . . . . . . . . . 24
Double cut . . . . . . . . . . . . . . . 35
Drive C. . . . . . . . . . . . . . . . . . 51
Drive D. . . . . . . . . . . . . . . . . . 51
EAN Readline. . . . . . . . . . . . . 31
EAN sep. lines . . . . . . . . . . . . 32
EasyPl. file log . . . . . . . . . . . . 87
EasyPlug error . . . . . . . . . . . . 56
EasyPlug monitor. . . . . . . . . . 89
End print mode. . . . . . . . . . . . 69
EP Monitor Mode . . . . . . . . . . 90
Error Checking. . . . . . . . . . . . 82
Error Indication. . . . . . . . . . . . 82
Error output . . . . . . . . . . . . . . 67
Error Polarity . . . . . . . . . . . . . 68
Error reprint . . . . . . . . . . . . . . 55
Ethernet speed. . . . . . . . . . . . 45
External signal . . . . . . . . . . . . 59
Factory settings . . . . . . . . . . . 85
Feed adjust. . . . . . . . . . . . . . . 91
Feed input . . . . . . . . . . . . . . . 67
Feed speed . . . . . . . . . . . . . . 27
Feedadjust label. . . . . . . . . . . 91
Flash mem size . . . . . . . . . . 102
Flashdata status . . . . . . . . . . 22
Foil diameter . . . . . . . . . . . . . 99
Foil end warning . . . . . . . . . . 52
Foil mode. . . . . . . . . . . . . . . . 55
Foil warn stop . . . . . . . . . . . . 52
Font downl. area . . . . . . . . . . 61
Font status. . . . . . . . . . . . . . . 19
Format Prefix. . . . . . . . . . . . . 80
FPGA version . . . . . . . . . . . 100
Frame error . . . . . . . . . . . . . . 41
Frame error . . . . . . . . . . . . . . 42
Frame error . . . . . . . . . . . . . . 43
Free store size. . . . . . . . . . . . 62
FTP password . . . . . . . . . . . . 46
FTP server. . . . . . . . . . . . . . . 46
Gap detect mode. . . . . . . . . . 58
Gateway address. . . . . . . . . . 45
Head exchange . . . . . . . . . . . 88
Head resistance. . . . . . . . . . . 56
Head run length. . . . . . . . . . . 98
Head strobes . . . . . . . . . . . . . 99
Head temperature . . . . . . . . . 99
Headnumber . . . . . . . . . . . . . 97
Head-sensor dist.. . . . . . . . . . 54
Image Save Path. . . . . . . . . . 82
Interface delay. . . . . . . . . . . . 39
Interface. . . . . . . . . . . . . . . . . 38
Intern. rewinder . . . . . . . . . . . 97
IP address . . . . . . . . . . . . . . . 44
IP addressassign. . . . . . . . . . 44
Keyboard . . . . . . . . . . . . . . . . 63
Label Invert . . . . . . . . . . . . . . 83
Label Top. . . . . . . . . . . . . . . . 81
Language. . . . . . . . . . . . . . . . 63
Left Position. . . . . . . . . . . . . . 81
Light sens. type . . . . . . . . . . . 54
Log files delete. . . . . . . . . . . . 87
MAC address. . . . . . . . . . . . 100
MAC address. . . . . . . . . . . . . 45

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
14
Manual Calibrate. . . . . . . . . . . 81
Manufacturer. . . . . . . . . . . . 101
Matend tolerance . . . . . . . . . . 91
Material length . . . . . . . . . . . . 28
Material type. . . . . . . . . . . . . . 28
Material width . . . . . . . . . . . . . 28
Max rew. current. . . . . . . . . . . 78
Max. Labellength . . . . . . . . 103
Max. rew. current . . . . . . . . . . 75
Memory card test . . . . . . . . . . 92
Memory status . . . . . . . . . . . . 18
Min. rew. current. . . . . . . . . . . 75
Min. rew. current. . . . . . . . . . . 78
Miss. label tol.. . . . . . . . . . . . . 58
Net mask. . . . . . . . . . . . . . . . . 44
No. of data bits . . . . . . . . . . . . 40
No. of data bits . . . . . . . . . . . . 41
No. of data bits . . . . . . . . . . . . 43
Offline mode. . . . . . . . . . . . . . 39
Operation time . . . . . . . . . . . . 99
Parity. . . . . . . . . . . . . . . . . . . . 40
Parity. . . . . . . . . . . . . . . . . . . . 41
Parity. . . . . . . . . . . . . . . . . . . . 43
Pause input. . . . . . . . . . . . . . . 67
PCB part number . . . . . . . . 101
PCB revision. . . . . . . . . . . . 100
Periph. device. . . . . . . . . . . . . 59
Peripheraldriver . . . . . . . . . . . 96
Port address. . . . . . . . . . . . . . 45
Print contrast. . . . . . . . . . . . . . 60
Print direction . . . . . . . . . . . . . 29
Print info mode . . . . . . . . . . . . 62
Print Interpret.. . . . . . . . . . . . . 52
Print speed . . . . . . . . . . . . . . . 27
Printer ID No. . . . . . . . . . . . . . 39
Printer status. . . . . . . . . . . . . . 16
Printer type. . . . . . . . . . . . . . . 84
Printtest. . . . . . . . . . . . . . . . . . 95
Product length. . . . . . . . . . . . . 74
Production date. . . . . . . . . . 101
PS temperature . . . . . . . . . . 100
Pullback current . . . . . . . . . . . 76
Pullback current . . . . . . . . . . . 79
Punch level. . . . . . . . . . . . . . . 37
Punch mode. . . . . . . . . . . . . . 37
Punch offset. . . . . . . . . . . . . . 30
Punch y calibr. . . . . . . . . . . . . 91
Ram disk size. . . . . . . . . . . . . 60
Ram memory size . . . . . . . . 102
Realtime clock . . . . . . . . . . . . 65
Receive test . . . . . . . . . . . . . . 94
Reference label . . . . . . . . . . . 25
Reprint function . . . . . . . . . . . 62
Reprint Signal. . . . . . . . . . . . . 66
Resolution . . . . . . . . . . . . . . . 81
Rewind direction. . . . . . . . . . . 36
Rewind direction. . . . . . . . . . . 78
Rewinder adjust . . . . . . . . . . . 95
RFID Option. . . . . . . . . . . . . . 50
RFID stat. del. . . . . . . . . . . . . 87
RFID Status . . . . . . . . . . . . . . 26
Roll number . . . . . . . . . . . . . . 97
Roll run length . . . . . . . . . . . . 98
Roller exchange. . . . . . . . . . . 88
Rotated Barcodes. . . . . . . . . . 32
SD card . . . . . . . . . . . . . . . . 103
Send test . . . . . . . . . . . . . . . . 93
Sens. punch-LS . . . . . . . . . . . 55
Sensor adjust. . . . . . . . . . . . . 90
Sensor test . . . . . . . . . . . . . . 90
Serial number. . . . . . . . . . . . 100
Serial Port Mode. . . . . . . . . . . 42
Serv. data reset . . . . . . . . . . . 89
Serv. operations. . . . . . . . . . . 97
Service Status . . . . . . . . . . . . 23
Service. . . . . . . . . . . . . . . . . . 88
Single job mode . . . . . . . . . . . 56
Singlestartquant. . . . . . . . . . . 59
SNMP agent. . . . . . . . . . . . . . 45
SNMP password. . . . . . . . . . . 45
Space for Jobs. . . . . . . . . . . 103
Spooler mode . . . . . . . . . . . . 38
Spooler size. . . . . . . . . . . . . . 39
StandAlone Input. . . . . . . . . . 50
Start cur. len. . . . . . . . . . . . . . 76
Start cur. len. . . . . . . . . . . . . . 79
Start error stop. . . . . . . . . . . . 74
Start offset . . . . . . . . . . . . . . . 73
Start print mode. . . . . . . . . . . 60
Start print mode. . . . . . . . . . . 66
Start rew. curr.. . . . . . . . . . . . 78
Start rew. current. . . . . . . . . . 76
Start source . . . . . . . . . . . . . . 73
Status output . . . . . . . . . . . . . 68
Status polarity . . . . . . . . . . . . 68
Stop bits. . . . . . . . . . . . . . . . . 40
Stop bits. . . . . . . . . . . . . . . . . 42
Stop bits. . . . . . . . . . . . . . . . . 43
Store Diagnosis . . . . . . . . . . . 86
Store Parameters. . . . . . . . . . 85
Sync. Interval. . . . . . . . . . . . . 49
System date. . . . . . . . . . . . . . 96
System revision . . . . . . . . . . . 96
System version . . . . . . . . . . . 96
Temp. reduction. . . . . . . . . . . 57
Thin line emphas . . . . . . . . . . 57
Time client . . . . . . . . . . . . . . . 49
Time server IP . . . . . . . . . . . . 49
Tot. foil length . . . . . . . . . . . . 98
Tot. mat. length . . . . . . . . . . . 98
Total cuts. . . . . . . . . . . . . . . . 98
Tradit. Imaging . . . . . . . . . . . 31
Turn-on mode . . . . . . . . . . . . 55
Type. . . . . . . . . . . . . . . . . . . 100
uMon . . . . . . . . . . . . . . . . . . . 96
UPC plain-copy . . . . . . . . . . . 31
USB select. . . . . . . . . . . . . . . 44
Voltage offset. . . . . . . . . . . . . 58
WEB admin passw. . . . . . . . . 48
WEB display refr . . . . . . . . . . 48

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
15
WEB server. . . . . . . . . . . . . . . 47
WEB supervisor p. . . . . . . . . . 48
Work place . . . . . . . . . . . . . 101
X - Printadjust. . . . . . . . . . . . . 36
Y – Printadjust . . . . . . . . . . . . 36

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
16
PRINT INFO
¯Printing of individual reports can be deactivated for certain options (e. g.
for the infeed option).
A material width of 100 mm is necessary to print the reports. The status print-
out is approx. 200 mm long.
Printer status
AP5.4 AP5.6
A protocol can be printed to get an overview of customer-specific parameter
settings (three pages, see [1]).
¯Which parameters are listed, depends on the printer type.
[1] Example printout „printer status“ (64-05 with firmware version 2.46).
Listed items: ySystemversion:
– Shows the installed firmware version as well as the release date of this
version.
– Firmware version: R = firmware RISC processor, H = firmware
H8 processor.

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
17
yPrinter type:
– Shows the printer type, which has been set using parameter
SERVICE FUNCTIONS > printer type (e.g. Avery 64-04)
– "USA" displayed after the printer type indicates that the USA font is loaded.
– "8DOT" displayed after the printer type indicates that the 8-Dot emulation
is loaded.
yPrinter Parameter Menu
Shows the setting of the parameters in the PRINT PARAMETERS menu.
yPrinter Interface Menu
Shows the setting of the parameters in the INTERFACE PARA menu.
yPrinter system menu
Shows the setting of the parameters in the SYSTEM PARAMETERS menu.
yDispenser Interface
Shows the setting of the parameters in the DP INTERFACE menu.
yInternal Options
– Default values: Shows the values which are used in case of a factory reset
(Standard or Default). See parameter SPECIAL FUNCTION > Default Values.
– RealtimeClock:Showsthe settimeanddate,ifa realtimeclockis installed.
In case of a too low battery, the line "Battery empty" is added.
– 2. com port: Shows if an additionall serial Interface is installed (not
supported).

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
18
Memory status
AP5.4 AP5.6
A memory protocol can be printed to provide an overview of the distribution
of the available memory capacity (one page).
[2] Example of a memory Status printout.
Listed items: yInternal Memory Configuration
PSee paragraph > MEMORY DATA on page 168.
yLogos on RAM disc
yGraphics on RAM disc
yFonts on RAM disc
PSee Plug-in card manual , topic section „Application“, chapter „Compact-
Flash card“.

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
19
Font status
AP5.4 AP5.6
Print samples of all installed characters, bar codes and line samples
(several pages).
Page „Font Library“ shows a list of the internal fonts and line styles.
Internal Fonts «Use the Easy-Plug commands listet in the first column of the report
(e.g. #YT100), to print using the appropriate font.
PEasy Plug commands: Refer to the Easy Plug Manual, topic section
Description of Commands .
PFor a list of all characters contained in the internal fonts, refer to the User
Manual, topic section Internal Fonts .
[3] Print sample „Font Status“ / „Font Library“.
Internal Line Styles «Use the line style number (fist column) with one of the Easy Plug commands
#YL or #YR to print lines in the matching style.
PEasy Plug commands: Refer to the Easy Plug Manual, topic section
Description of Commands .
¯Additionally, the following line styles are available:
– 13: Checked pattern with 3 dot edge length
– 14: Checked pattern with 1 mm edge length
– 15: Checked pattern with 5 mm edge length

03/10 Rev. 5.05-00 USER- / SERVICE MANUAL Info-Printouts & Parameters
AP5.4 Gen II – AP5.6
20
¯The line width has to be defined as a multiple of the edge length of the
checked pattern!
Internal bar codes The pages titled „Barcode Library“ show print samples of the internal bar
codes (see [4], [8]).
[4] Print sample „Font Status“ / „Font Library“: Bar code listing.
yOnedimensional bar codes are printed with the Easy-Plug command #YB,
see manual Easy-Plug, topic section Description of Commands .
yTwo-dimensional bar codes are printed by means of special Easy-Plug
commands:
yGS1 DataBar (formerlyRSS) and CompositeComponent (CC)bar codes are
printed by means of the Easy-Plug command #RSS. The bar code is
Easy-Plug command Bar code
#IDM Data Matrix Code
#MXC Maxi Code
#PDF PDF 417
#CBF Codabar F
#CFN Code 49
#SQR QR Matrix Code
[1] Internal, two-dimensional bar codes.