AVProConnect AC-MX1616-AUHD User manual

AC-MX1616-AUHD
pg. 1
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
User Manual
AC-MX1616-AUHD
18 Gbps True 4K60 4:4:4 16x16 HDMI Matrix
w/ Audio De-Embedding & Routing.

AC-MX1616-AUHD
pg. 2
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Common Usage Diagram

AC-MX1616-AUHD
pg. 3
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Specifications:

AC-MX1616-AUHD
pg. 4
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
The AC-MX1616-AUHD is a true high bandwidth powerhouse. Supporting the full HDMI 2.0a/b specification and
supporting every flavor of HDR, this matrix will ensure you can get the most out of any system. This unit supports
uncompressed HDR formats Including HDR, HDR10, HDR10+, Dolby Vision, HLG, BBC and NHK. All of them are supported
in up to 4K 60Hz and up to 12 Bit Deep Color. All color space compression is compatible.
Our unique design has allowed us to improve high bandwidth switching speeds. Average speeds of less than 3 seconds –
this is an industry best for this advanced level of actual uncompressed, high bandwidth w/ HDR switching. Maximum
compatibility and speed improve the customer experience immensely.
The sleek, low-profile and high-density design make for a sleek machine that saves you valuable space in the rack room.
This combined with a OLED setup screen on the front that makes setup and management a breeze will make this a staple
in your large demanding installations!
Features:
•HDMI 2.0(a/b)
•18Gbps Bandwidth Support
•4K60 4:4:4 Support
•Ultimate HDR Support (HDR 10 & 12 Bit)
•Dolby Vision, HDR10+ and HLG Support
•HDCP 2.2 (and all earlier versions supported)
•Simple setup with front panel control screen
•WebOS for simple connectivity and control/management
•Ultra-Low Profile (1U)
•Fast Switching
•Advanced EDID Management
•IR, RS-232 and LAN Control Options
•Digital Coax Audio Out (6CH PCM, DD, DTS)
•Driver Support for Crestron, C4, RTI, ELAN and more!!!
•Extracted Audio Now Has 3 Operating Modes. Bound to Input,
Bound to Output, or Independent Matrix
Easy to use:
• Feature rich
• Fast Switching
• Setup screen
• IR Remote
• IR & RS-232 Control
• LAN Control
Applications:
•Bars and Restaurants are absolutely perfect. Low downtime and robust implementation make for happy owners
and repeat work.
•In medical facilities for multiview point to point training environments
•For classrooms with lots of displays and presenters
•For security applications to view 4-9 HD video cameras
•For transportation management systems for monitoring camera feeds in hi-def.
•Large homes that want the ultimate control experience
In The Box:
• AC-MX1616-AUHD Matrix
• IR Remote Control
• IR Extension Cable
• 12V/5A Locking Power Supply
• Rack Ears & Phoenix Connectors
• Instruction Manual

AC-MX1616-AUHD
pg. 5
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Device Feature Overview:
Uncompressed ~ Uncompressed base-band video means that what you put in it what comes out. This allows the
integrator ultimate control to use any infrastructure they want. Use pure fiber like Cleerline, Bullet Train Cables (Long
Haul, Shout Haul), or 18Gbps HDBaseT Extenders (AC-EX40-444) to get the full bandwidth and full picture!
Ultimate HDR Support ~ This matrix supports all flavors of HDR in all formats. Including HDR, HDR10, HDR10+, Dolby
Vision, HLG, BBC and NHK. All of them are supported in up to 4K 60Hz and up to 12 Bit Deep Color. All color space
compression are compatible.
Extreme EDID Management ~ With 29 on board EDID's, including HDR EDID’s, not getting a picture is simply a thing of
the past. You can manage the input side of the switch by selecting a preloaded EDID. It also has the ability to
INSTANTLY read an EDID from any connected display and apply it to the desired input, all with the push of a button.
Goodbye EDID problems...
Front Panel Screen ~ Make setup a breeze! The front panel allows you to do basic setup including; EDID, Audio,
Matrixing and network. All without connecting a PC or hooking anything up. This additional mode of control is a
welcome resource on the job site.
WebOS~ Full matrix control is available on the internal WebOS - Simply plug the matrix into the network and punch in
the default IP (192.168.1.239) or use DHCP to connect to a full control system! The WebOS is designed with mobile
devices in mind, so feel free to use you phone or tablet for real-time control.
Fast Switching ~ Our unique design has allowed us to improve high bandwidth switching speeds. Average speeds of
less than 3 seconds – this is an industry best for this advanced level of actual uncompressed, high bandwidth w/ HDR
switching.
Audio De-Embedding ~ Our unique Audio De-Embedding allows 3 modes - Bind to Input, Bind to Output, or Matrix.
HDMI Outputs
Control
Screen
IR Receiver
for Switch
Control
Control Pad
Used w/
Control Screen
Input (Source) & Output (Sink) Select
(Choose Output, press Enter, choose Input)
HDMI Inputs

AC-MX1616-AUHD
pg. 6
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
1. Connect the HDMI input sources (Blu-ray, Set Top Box, etc...) to the AC-MX1616-AUHD
2. Connect the HDMI output devices (AVR, Display, Distribution Amplifier, Extender) to the AC-MX1616-AUHD
3. Power on the sources
4. Connect the power supply's into the AC-MX1616-AUHD (You need to plug in both supply's)
5. Turn on output devices/displays
6. You may now use the front panel controls, supplied IR remote or free PC software to control the switch.
Front Panel Control
Switching:
The AC-MX1616-AUHD can be switched from the front panel by selecting the OUTPUT, Press ENTER, then select the INPUT:
1. Press the button (1 through 16) that corresponds with the OUTPUT (Display, or Sink Device) you
would like to send a source.
2. Press ENTER
3. Now select the desired INPUT on (1 through 16)
4. The route is now set.
5. You may also navigate to the "Switch" Menu on the Control Screen to manage the
routes (See "Switch Routing" below)
Figure 1 –Switching with the front panel controls. NOTE: Select the OUTPUT and then press ENTER, then
select the INPUT
Basic Setup:
Quick Setup:
STEP 1: Select the desired OUTPUT
STEP 3: Select the desired INPUT
STEP 2: Press ENTER

AC-MX1616-AUHD
pg. 7
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Navigating the Control Screen:
You can use the control screen to setup/control several key features including:
•Matrix Switch Routing ~ Control switching or view the current routing
•EDID Management ~ View, adjust EDID Configuration
•Audio Setup & Routing ~ Set the default extracted audio mode to Bind to Input,
Bind to Output or Matrix - When in Matrix, audio route can be selected.
•Network Setup ~ View/Setup IP Address (Host/device, Gateway, Subnet),
Toggle DHCP, set port number and view MAC Address
To navigate the control screen you have a 6-button control panel that control the "Control" Screen.
•"Menu" area consists of UP, DOWN, LEFT and RIGHT - These are your navigation buttons. Press
these buttons to move through them menus to your desired selections. Your desired selection will
be bordered or highlighted
•"Enter" Selects the highlighted item and advances to the next set of options or sets your selection
•"Cancel" Stops what you are doing and takes you back one menu or to the home screen.
Home Screen
Control Screen
Control Screen Navigation Buttons
Control Screen - Switch Routing:
Once you select the "Matrix" option, you have 2 primary functions:
1. View the current rout settings so you can verify that your system is working properly and the routes
are correct
2. Set new matrix routes. You can change the matrix routes here as well, this is good for demonstrating
switching.
NOTE: When setting a new route, select OUTPUT first then INPUT
Select Output First
Then Choose
Input
Select "Matrix"

AC-MX1616-AUHD
pg. 8
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Control Screen - EDID Management:
Instantly and easily set and manage EDID functions right from the front screen. EDID management will help
you get the right signal from the source device adding additional security that nothing unsupported will be
mistakenly fed into the system.
EDID effectively tells the source what the system is capable of handling, devices without robust EDID control
just have to hope the source behaves how we want it to. With the AC-MX1616-AUHD you control the
sources:
To Set the EDID, just choose EDID from the "Home Screen" and then select the INPUT you want to set. Finally
toggle through the EDIDs until you get the one you want. For the most plug and play compatibility, we
recommend using "1080P 2CH" (Which is the default setting). This is ideal for bars, restaurants, and homes.
There is also the ability to upload a custom EDID is desired (Has to be done in Serial Control Software).
Available EDID options are listed below. Additionally, you can copy an EDID from a display using Serial (more
later in this manual) - This is recommended for advanced users doing HDR distribution.
Select "EDID"
Choose
Input To
Apply EDID
to
Select the desired EDID
Available EDID's:
0.
1080P_2CH
1. 1080P_6CH
2. 1080P_8CH
3. 1080P_3D_2CH
4. 1080P_3D_6CH
5. 1080P_3D_8CH
6. 4K30HZ_3D_2CH
7. 4K30HZ_3D_6CH
8. 4K30HZ_3D_8CH
9. 4K60HzY420_3D_2CH
10. 4K60HzY420_3D_6CH
11. 4K60HzY420_3D_8CH
12. 4K60HZ_3D_2CH
13. 4K60HZ_3D_6CH
14. 4K60HZ_3D_8CH
15. 1080P_2CH_HDR
16. 1080P_6CH_HDR
17. 1080P_8CH_HDR
18. 1080P_3D_2CH_HDR
19. 1080P_3D_6CH_HDR
20. 1080P_3D_8CH_HDR
21. 4K30HZ_3D_2CH_HDR
22. 4K30HZ_3D_6CH_HDR
23. 4K30HZ_3D_8CH_HDR
24. 4K60HzY420_3D_2CH_HDR
25. 4K60HzY420_3D_6CH_HDR
26. 4K60HzY420_3D_8CH_HDR
27. 4K60HZ_3D_2CH_HDR
28. 4K60HZ_3D_6CH_HDR
29. 4K60HZ_3D_8CH_HDR
30. User EDID 1
31. User EDID 2
32. User EDID 3

AC-MX1616-AUHD
pg. 9
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Control Screen - Audio Settings
Audio Settings has two functions:
Function 1 - Set the default extracted audio mode. There are three options:
•Bind to output (extracted audio witches with the video, this is the default mode)
•Bind to input (extracted audio is fixed to the corresponding input by the same number)
•Independent/Matrix (extracted audio can be routed however you like and there are commands to allow it
to function as a separate matrix)
Choose "VIEW AUDO"
Highlight this area and press
"ENTER". You can now toggle
up and down to select the
mode.
Function 2 - View/Route Extracted Audio Matrix. (NOTE: you can only route the audio if "MATRIX" mode is
selected above. To route audio, follow the same logic as video switching in this menu:
1. Select the extracted audio OUTPUT first by pressing the number or navigating to it
2. Press ENTER to set the selection
3. Select the desired INPUT by toggling to it with UP/DOWN or simply selecting the number on the keypad.
4. Press ENTER (This only applies if you used up/down to toggle to your desired input)
Choose "VIEW AUDO"
Press the desired extracted audio
OUTPUT number
Make sure
this area
says
MATRIX
Press Enter
Press the desired INPUT number

AC-MX1616-AUHD
pg. 10
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Control Screen - Network (IP) Setting
Here you can setup the Matrix with your preferred network settings. From the front panel you can:
•View the current IP Settings and MAC address
•Set static Route IP (Default is 192.168.001.001)
•Set static Device IP (Device Default is 192.168.001.239)
•Set Static Net Mask (Default is 255.255.255.0)
•Change the TCP/IP Port (Default is Port 23)
•Toggle DHCP (Default condition is DHCP OFF) (0=OFF, 1=ON)
To navigate the IP Setting Screen:
1. Navigate up and down to select (Use Enter Button) the option you want to address (RIP, IP,
Mask, TCP.IP, DHCP)
2. Once selected you can use up and down to to change the first number or press enter to skip
it and continue to the next.
3. Once you set the last possible number (Or complete the IP) it will back you to the main
screen to make another selection
Route IP
Device IP Address
Subnet Mask
TCP/IP Port
MAC Address
DHCP
Toggle
(0=OFF,
1=ON)
NOTE: You can send Telnet commands to the machine by IP, the commands are the same commands used for RS232
listed in the "Command List"

AC-MX1616-AUHD
pg. 11
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
IR Details:
IR IN on this machine is for controlling the AC-MX1616-AUHD, RS232 or IP Control are the recommended methods,
but IR can be used in some circumstances. The IR INPUT is for an IR Receiver EYE only. The IR Receiver Eye below can
plug into the IR Ext. port.
IR Remote Control:
The Matrix can be switched with IR Commands (Remote or other) in several ways:
1. Use the supplied IR Remote (Pictured) and select the OUTPUT then INPUT
2. Lear IR Codes from the supplied remote
3. Use discreet NEC/HEX IR Codes to program a 3rd party control system or IR remote. Check
www.avproconnect.com for discreet IR codes or contact us to get them.

AC-MX1616-AUHD
pg. 12
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
RS232 Details:
Here is a sample cable. in this example you can see how to connect or build and RS232 cable to use to control
the Matrix. The pin configuration is shown here as well.
You can send serial commands in the 3-Pin port or the USB port
3-Pin RS232
USB has a built in USB-->Serial
driver, a com port will be set
up on the PC

AC-MX1616-AUHD
Serial Command List & Settings
Settings: Baud Rate 57600, Data Bits 8, No Parity, 1 Stop Bit
NOTE - Visit www.avproconnect.com to get the Notepad
version of the command list for easy copy/past access.
pg. 13
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
== Azz : All Commands start by Prefix System Address zz, if [01~99] ==
==----------------------------------------------------------------------------------------==
== System Control Setup Commands: ==
== H : Help ==
== STA : Show Global System Status ==
== SET RST : Reset to Factory Defaults ==
== SET ADDR xx : Set System Address to xx {xx=[00~99](00=Single)} ==
== SET CAS EN/DIS : Set Cascade Mode Enable/Disable ==
== SET LCD ON Tx : Set LCD Remain On Time{x=[0~3](0=Always ON,1=15,2=30,3=60Sec) ==
== SET KEY LOCK ON/OFF : Set Key Lock On/Off ==
== GET ADDR : Get System Address ==
== GET CAS : Get Cascade Mode Status ==
== GET STA : Get System System Status ==
== GET INx SIG STA : Get Input x Signal Status{x=[0~16](0=ALL)} ==
== GET LCD ON T : Get LCD Remain On Time ==
== GET KEY LOCK : Get Key Lock Status
==
==----------------------------------------------------------------------------------------==
== Output Setup Command : (Note:output number(x)=HDMI(x),x=1-16) ==
== SET OUTx VS INy : Set Output x To Input y {x=[0~16](0=ALL), y=[1~16]} ==
== SET OUTx EXA EN/DIS : Set Ex-Audio Output Enable/Disable{x=[0~16](0=ALL)} ==
== SET EXAMX MODEx : Set Ex-Audio Matrix Mode ==
== {x=[0~2](0=Bind To Output,1=Bind To Input,2=Matrix} ==
== SET OUTx AS INy : Set Ex-Audio Output x To Input y{x=[0~16](0=ALL), y=[1~16]} ==
== SET OUTx STREAM ON/OFF: Set Output x Stream ON/OFF{x=[0~16](0=ALL)} ==
== GET OUTx VS : Get Output x Video Route{x=[0~16](0=ALL)} ==
== GET OUTx EXA : Get Ex-Audio Output Enable/Disable Status{x=[0~16](0=ALL)} ==
== GET OUTx EDID DATA : Get Output x EDID DATA{x=[1~16]} ==
== GET EXAMX MODE : Get Ex-Audio Matrix Mode ==
== GET OUTx AS IN : Get Output x Ex-Audio Route{x=[0~16](0=ALL)} ==
== GET OUTx STREAM : Get Output x Stream ON/OFF Status{x=[0~16](0=ALL)} ==
==----------------------------------------------------------------------------------------==

AC-MX1616-AUHD
Command List cont:
== Input Setup Command: (Note:input number(x)=HDMI(x),x=1-16) ==
== SET INx EDID y : Set Input x EDID{x=[0~16](0=ALL), y=[0~32]} ==
== ==
== 0:1080P_2CH(PCM) 1:1080P_6CH 2:1080P_8CH ==
== 3:1080P_3D_2CH(PCM) 4:1080P_3D_6CH 5:1080P_3D_8CH ==
== 6:4K30Hz_3D_2CH(PCM) 7:4K30HZ_3D_6CH 8:4K30HZ_3D_8CH ==
== 9:4K60Hz(Y420)_3D_2CH(PCM) 10:4K60Hz(Y420)_3D_6CH 11:4K60Hz(Y420)_3D_8CH ==
== 12:4K60HZ_3D_2CH 13:4K60HZ_3D_6CH 14:4K60HZ_3D_8CH ==
== 15:1080P_2CH(PCM)_HDR 16:1080P_6CH_HDR 17:1080P_8CH_HDR ==
== 18:1080P_3D_2CH(PCM)_HDR 19:1080P_3D_6CH_HDR 20:1080P_3D_8CH_HDR ==
== 21:4K30Hz_3D_2CH(PCM)_HDR 22:4K30Hz_3D_6CH_HDR 23:4K30Hz_3D_8CH_HDR ==
== 24:4K60Hz(Y420)_3D_2CH(PCM)_HDR 25:4K60Hz(Y420)_3D_6CH_HDR 26:4K60Hz(Y420)_3D_8CH_HDR ==
== 27:4K60Hz_3D_2CH(PCM)_HDR 28:4K60Hz_3D_6CH_HDR 29:4K60Hz_3D_8CH_HDR ==
== 30:USER1_EDID 31:USER2_EDID 32:USER3_EDID ==
== SET INx EDID CY OUTy : Copy Output y EDID To Input x(USER1 BUF) ==
== {x=[0~16](0=ALL), y=[1~16]} ==
== SET INx EDID Uy DATAz: Write EDID To User y Buffer of Input x ==
== {x=[0~16](0=ALL), y=[1~3],z=[EDID Data] ==
== GET INx EDID : Get Input x EDID Index ==
== {x=[0~16](0=All)} ==
== GET INx EDID y DATA : Get Input x EDID y Data ==
== {x=[1~16],y=[0~32} ==
==----------------------------------------------------------------------------------------==
== IR Code Setup: ==
== SET IR SYS xx yy : Set IR System Code ==
== {xx=[00~FFH],yy=[00~FFH] ==
== SET IR OUTx INy CODE zz : Set IR Data Code ==
== {x=[1~16],y=[1~16],zz=[00~FFH]} ==
== GET IR SYS : Get IR System Code ==
== GET IR OUTx INy CODE : Get IR Data Code ==
== {x=[0~16](0=All),y=[1~16]} ==
==----------------------------------------------------------------------------------------==
== Network Setup Command: ( xxx=[000-255], zzzz=[0001~9999] ==
== SET RIP xxx.xxx.xxx.xxx : Set Route IP Address to xxx.xxx.xxx.xxx ==
== SET HIP xxx.xxx.xxx.xxx : Set Host IP Address to xxx.xxx.xxx.xxx ==
== SET NMK xxx.xxx.xxx.xxx : Set Net Mask to xxx.xxx.xxx.xxx ==
== SET TIP zzzz : Set TCP/IP Port to zzzz ==
== SET DHCP y : Set DHCP {y=[0~1](0=Dis,1=Enable)} ==
== GET RIP : Get Route IP Address ==
== GET HIP : Get Host IP Address ==
== GET NMK : Get Net Mask ==
== GET TIP : Get TCP/IP Port ==
== GET DHCP : Get DHCP Status ==
== GET MAC : Get MAC Address ==
============================================================================================
pg. 14
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
Settings: Baud Rate 57600, Data Bits 8, No Parity, 1 Stop Bit
NOTE - Visit www.avproconnect.com to get the Notepad
version of the command list for easy copy/past access.

AC-MX1616-AUHD
Using Multiple Units In One System:
Device Addresses When Using Serial Communication:
NOTE: Only set device address when cascading multiple units together and using RS232 as your control method!
You also have to send the device address when doing advanced routing while sending commands by serial (next
page) even if it is default "A00". You NEVER use device addresses when using IP control or TELNET
When using serial communication it is good to be aware of the devices "Address" You will want to know the
device address as this will determine which Cloud 9 will receive a command. All of the drivers are built so that if
you use serial communication you will use ONE instance of the driver and select the size. i.e 9x18, 9x27 etc...
All Cloud 9's are address "A00" by default and if you are using just one device you do not need to place this in
front of the serial command.
EX1: If you have a standalone unit and are using serial control you can just send a command without the address:
"SET OUT5 VS IN3" ----This will set Output 5 to Input 3
EX2: If you have two units in a system you have to label them A01 and A02, so a command will look like:
"A02SET OUT5 VS IN3" ----This will set Output 5 to Input 3 ON SWITCH TWO. Also, please note that there is no
"space" between the address and the command
To set and device address you can use the PC Control Software or send the command "SET ADDR xx" (xx = 01
through 99)
Cascading with IP Control:
With IP you have to have a direct IP connection to each unit, and regard them as individual matrices. So for a 9
units in a system with IP control, you have to connect Ethernet to all 9 matrices. If you are using a 3rd party
control driver, install 9 instances of the drivers, and regard them all as individual 16x16 matrices.
When using IP DO NOT use serial system addresses, as the IP addresses will serve the same purpose While it can
be done if one so desires, it complicates the programming.
A best practice is to set a static IP address for each unit, rather than DHCP.
pg. 15
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]

AC-MX1616-AUHD
Extracted Audio:
The extracted audio ports have distinct operating modes. Your desired mode can be set to suite your
particular installation. The 3 modes are:
From Input ~ This is the default configuration. In this mode the audio port number corresponds to the INPUT
signal. This is ideal for systems where audio is matrixed separately in a zoned amplifier.
From Output ~ This configuration will automatically have the audio follow OUTPUT, so the audio from the
extracted port always matches the HDMI output. This is ideal for systems that use local AVR's for some of the
zones.
Independent/Matrix ~ This mode allows you matrix the extracted audio outputs independent of HDMI. In
this mode a new set of commands becomes available to be able to route audio however you want. This can
be used as a separate zoned audio matrix with only using an amplifier.
Setting up Extracted Audio Routing:
You can set up Extracted Audio Routing in the PC Software, Driver or by sending the following command:
SET EXA MODEy -- Where (y=0-2) 0=From Input, 1=From Output, 2=Independent.
If you set to "Independent" a new set of commands is available to you to matrix the ports:
SET OUTx EAS INy -- Where (x=0-16) 0=ALL, 1-16=Desired Output & (y=1-16) 1-16=Desired Input
NOTE: Extracted Audio Ports are PCM 2CH audio up to LPCM 6 CH, Dolby Digital 5.1 & DTS. No down-mix.
Audio Diagrams:
pg. 16
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]

AC-MX1616-AUHD
Extracted Audio cont:
Audio Diagrams:
pg. 17
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]

AC-MX1616-AUHD
pg. 18
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
PC Control Software - Side Bar:
Note: PC Control Software can be used when connected to the RS232 or Mini USB Port.
Connection Area - Use the drop down to select the COM Port or
press "Search Machine" to search your computer for open COM
Ports. The light will be red if there is a successful connection.
Select/Manage Addresses - Use the drop down to select the
Address of the device you want to control (If cascading multiple
units). Press "Address Management" to set the Addresses.
View "Address Management' Tab later for more.

AC-MX1616-AUHD
pg. 19
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
PC Control Software - Matrix Tab (OUTPUT 1-8):
Note: PC Control Software can be used when connected to the RS232 or Mini USB Port.
Switching - Simply choose the INPUT radio button you want to see on each output.

AC-MX1616-AUHD
pg. 20
AVProConnect ~ 3518 N Casco Ave. Sioux Falls, SD 57104~ 1.877.886.5112 ~ +1.605.274.6055 ~ [email protected]
PC Control Software - Matrix Tab (OUTPUT 9-16):
Note: PC Control Software can be used when connected to the RS232 or Mini USB Port.
Switching - Simply choose the INPUT radio button you want to see on each output.