AVS AVS-3610MHz User manual

USER MANUAL
AVS-3610MHz
36*10W LED MOVING HEAD
ZOOM
Thank you for choosing our moving head. For your own safety, please read
this manual before installing the device. This manual covers the important
information on installation and applications. Please install and operate the
fixture with following instructions. Meanwhile, please keep this manual well
for future needs.
This moving wash is made of a new type of high temperature strength of
engineering plastics and cast aluminum casing with nice outlook. The fixture
is designed and manufactured strictly following CE standards, complying
with international standard DMX512 protocol. It’s available independently
controlled and linkable with each other for operation.And it is applicable for
large-scale live performances, theater, studio, nightclubs and discos.
The fixture adopts powerful LED lamps which features high brightness and
stability. Please carefully unpack it when you receive the fixture and check
whether it is damaged during the transportation.And please check whether
the following items are included inside the box:
Power cable----one
User Manual----one
Signal Cable----one
Safety Instructions:
This device has left the factory in perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the
user to follow the safety instructions and warning notes written in this user
manual.
1

If the device has been exposed to temperature changes due to
environmental changes, do not switch it on immediately. The arising
condensation could damage the device. Leave the device switched off until
it has reached room temperature. This device falls under protection-class I.
Therefore it is essential that the device be earthed. The electric connection
must carry out by qualified person. The device shall only be used with rate
voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of
this manual. Make sure the power cord is never crimped or damaged by
sharp edges. If this would be the case, replacement of the cable must be
done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before
cleaning it. Only handle the power cord by the plug. Never pull out the plug
by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal
process and does not necessarily mean that the device is defective, it
should decrease gradually.
Please don't project the beam onto combustible substances. Fixtures can
not be installed on combustible substances, keep more than 50cm distance
with wall for smooth air flow, so there should be no shelter for fans and
ventilation for heat radiation.
If the external flexible cable or cord of this luminary is damaged, it shall
be exclusively replaced by the manufacturer or his service agent or a similar
qualified person in order to avoid a hazard
Maintenance and Cleaning
The following points have to be considered during the inspection:
1) All screws for installing the devices or parts of the device have to be
tightly connected and must not be corroded.
2) There must not be any deformations on the housing, color lenses,
fixations and installation spots (ceiling, suspension, trussing).
3）Mechanically moved parts must not show any traces of wearing and must
not rotate with unbalances.
4）The electric power supply cables must not show any damage, material
fatigue or sediments.
Further instructions depending on the installation spot and usage have to be
adhered by a skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we
suggest a regular cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakneness
of the lights due to accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three
month, make sure that the circuit contacts are in good condition,
prevent the poor contact of circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint-
free cloth. Never use alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the
instructions under “Installation instructions”.
Should you need any spare parts, please order genuine parts from your
local dealer.
Operation Instructions
-The moving head is an LED wash light for onsite decoration purpose.
2
3

-Don’t turn on the fixture if it’s been through severe temperature difference
like after transportation because it might damage the light due to the
environment changes. So make sure to operate the fixture until it is in
normal temperature.
-This light should be keep away from strong shaking during any
transportation or movement. Don’t pull up the light by only the head, or it
might cause damages to the mechanical parts.
-Don’t expose the fixture in overheat, moisture or environment with too
much dust when installing it. And don’t lay any power cables on the floor.
Or it might cause electronic shock to the people.
-Make sure the installation place is in good safety condition before installing
the fixture. Make sure to put the safety chain and check whether the screws
are screwed properly when installing the fixture. Make sure the lens is in
good condition. It’s recommended to replace the units if there are any
damages or severe scratch. Make sure the fixture is operated by qualified
person who knows the fixture before using.
-Keep the original packages if any second shipment is needed.
-Don’t try to change the fixtures without any instruction by the manufacturer
or the appointed repairing agencies.
-It is not in warranty range if there are any malfunctions from not following
the user manual to operate or any illegal operation, like shock short circuit,
electronic shock, lamp broke, etc.
Installation via clamp
Please refer to the picture below:
Screw one clamp each via a M12 screw and nut onto the Omega holders.
Insert the quick-lock fasteners of the first Omega holder into the respective
holes on the bottom of the device. Tighten the quick-lock fasteners fully
clockwise. Install the second Omega holder.
Pull the safety-rope through the holes on the bottom of the base and over
the trussing system or a safe fixation spot. Insert the end in the carbine and
tighten the safety screw.
DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your
controller and the other side to the male 3-pin XLR input of the moving head.
4
5

You can chain multiple moving head together through serial linking. The
cable needed should be two core, screened cable with XLR input and output
connectors. Please refer to the diagram below.
Address 26 Address13 Address 1
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an
electrically noisy environment, such as in a discotheque, it is recommended
to use a DMX terminator. This helps in preventing corruption of the digital
control signal by electrical noise.
The DMX terminator is simply an XLR plug with a 120 Ω resistor connected
between pins 2 and 3,which is then plugged into the output XLR socket of
the last fixture in the chain.
Please see illustrations below:
1
23
PIN 3
PIN 2
120Ω
LCD Display Operations
The display will close after 30 seconds without operations.
DMX Channels
6
7

Technical Specifications
36 pcs 10W 4in1 high power LEDs
50,000 hours lifespan and low power consumption
16 bit smooth and precise resolution for PAN/TILT movement
540°pan and 280°tilt movement
Scan position memory, auto reposition after unexpected movement
RGBW color mixing systemZoom:15 --60
LED dimming: DIM4 technology(adopt 4096 linearity dimmer)
LED rainbow effect
Macros effect
Strobe effect with 20 flashes per second and pulse effect
General dimming and blackout for all four colors
14 DMX channels
DMX512, maste r-slave, sound activation, auto-run
Blue LCD display
Input Voltage: AC90-240V. 50-60Hz
Fan standard: size: 90X90X25 –60X60X15
Fuse standard (at the bottom): 3.15A/250V
Power Consumption: 320W
Dimensions: 350x260x350mm
Packing Dimensions: 425x295x400mm
Net Weight: 10kgs
Gross Weight: 12kgs
Channel
Function
Value
Description
1
Pan
0-255
0---540 degree
2
Tilt
0-255
0---280 degree
3
Pan/Tilt speed
0-255
From slow to fast
4
Dimmer
0--255
0~100%
5
Red
0--255
0~100%
6
Green
0--255
0~100%
7
Blue
0--255
0~100%
8
White
0--255
0~100%
9
Strobe
0-255
From slow to fast
10
Zoom
0--255
15 degree to 60 degree
11
RGBW macro
function
000-004
No macro function
005-044
Eight kinds of fixed color
045-049
No function
050-094
Eight skip loop change color
095-099
No function
100-149
Eight kinds of circle color
150-154
No function
155-166
Red+green from dark to bright
167-178
Green+red from bright to dark
179-190
Green+blue from dark to bright
191-202
Blue+green from bright to dark
203-214
Blue+red from dark to bright
215-226
Red+blue from bright to dark
227-238
Red ,green+blue from dark to bright
239-250
Blue+red from dark to bright at the same
time green from bright to dark
251-255
Output 100%at the same time
12
Function speed
0-255
From slow to fast
13
Pan fine
0-255
1.8 degree
14
Tilt fine
0-255
1.8 degree
15
Reset/Auto
0--255
125-127Reset(3s). 250-255Auto
8
9