AXIOMTEK GOT-5840TL User manual

GOT-5840TL
All-in-One
8.4 SVGATFT Super Slim
Fanless Toudh Computer
User’s Manual

ii
Disclaimers
This manual has been carefullychecked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for anyinfringements ofpatents or anythird partys rights, and any
liabilityarising fromsuch use.
AXIOMTEK does not warrant or assume anylegal liabilityor
responsibilityfor the accuracy, completeness or usefulness ofany
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at anytime without notice.
No part ofthis document maybe reproduced, stored in a retrieval
system, or transmitted, in anyformor byanymeans, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission ofAXIOMTEK Co., Ltd.
Copyright 2009 AXIOMTEK Co., Ltd.
All Rights Reserved
April 2009, Version A3
Printed in Taiwan

iii
SafetyApprovals
uCE Marking
uFCC Class A
uFCC Compliance
This equipment has been tested in compliance with the limits for a
Class A digital device, pursuant to Part 15 ofthe FCC Rules. These
limits are meant to provide reasonable protection against harmful
interference in a residential installation. Ifnot installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequencyenergyand cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. Ifthis equipment does cause
harmful interference to radio or television reception, which can be
determined byturning the equipment off and on, the user is
encouraged to tryto correct the interference byone or more ofthe
following methods:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment to another outlet ofa circuit that
doesn t connect with the receiver.
4. Consult the dealer or an experienced radio/TV technician for
help.
Shielded interface cables must be used in order to complywith the
emission limits.

iv
SafetyPrecautions
Before getting started, please read the following important safety
precautions.
1. The GOT-5840TL does not come equipped with an operating
system. An operating systemmust be loaded first before
installing anysoftware into the computer.
2. Be sure to ground yourselfto prevent static charge when
installing the internal components. Use a grounding wrist
strap and place all electronic components in anystatic-
shielded devices. Most electronic components are sensitive
to static electrical charge.
3. Disconnect the power cord fromthe GOT-5840TL before any
installation. Be sure both the systemand external devices are
turned OFF. A sudden surge ofpower could ruin sensitive
components that the GOT-5840TL must be properly
grounded.
4. The brightness ofthe flat panel displaywill be getting weaker
as a result offrequent usage. However, the operating period
varies depending on the application environment.
5. Turn OFF the systempower before cleaning. Clean the
systemusing a cloth only. Do not sprayanyliquid cleaner
directlyonto the screen. The GOT-5840TL maycome with or
w/o a touchscreen. Although the touchscreen is chemical
resistant, it is recommended that you spraythe liquid cleaner
on a cloth first before wiping the screen. In case your system
comes without the touchscreen, you must followthe same
procedure and not sprayanycleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen.
Scratches on the touchscreen maycause malfunction or
internal failure to the touchscreen.
7. The flat panel displayis not susceptible to shockor vibration.
When assembling the GOT-5840TL, make sure it is securely
installed.
8. Do not open the system s backcover. Ifopening the cover for
maintenance is a must, onlya trained technician is allowed to
do so. Integrated circuits on computer boards are sensitive to
static electricity. To avoid damaging chips fromelectrostatic
discharge, observe the following precautions:

v
lBefore handling a board or integrated circuit, touch an
unpainted portion ofthe systemunit chassis for a few
seconds. This will help to discharge anystatic electricity
on your body.
lWhen handling boards and components, wear a wrist-
grounding strap, available frommost electronic
component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademarkofAXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks ofInternational
Business Machines Corporation.
Intel®and Pentium®are registered trademarks ofIntel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks ofMicrosoft
Corporation.
VIA is a trademarkofVIA Technologies, Inc.
SSTis a trademarkofSilicon Storage Technology, Inc.
UMC is a trademarkofUnited Microelectronics Corporation.
Other brand names and trademarks are the properties and registered
brands oftheir respective owners.

vi
Table of Contents
Disclaimers....................................................................................ii
SafetyApprovals...........................................................................iii
SafetyPrecautions.......................................................................iv
CHAPTER 1 INTRODUCTION..........................................................1
1.1 General Description.....................................................1
1.2 Specifications..............................................................2
1.2.1 Main CPU Board..........................................................2
1.2.2 I/O System..................................................................3
1.2.3 SystemSpecification..................................................3
1.3 Dimensions..................................................................5
1.4 I/O Outlets...................................................................7
1.5 Packing List.................................................................8
CHAPTER 2 HARDWARE INSTALLATION......................................9
2.1 CF Card Installation.....................................................9
2.2 Serial Ports Interface.................................................11
2.3 Ethernet.....................................................................13
2.4 Mountings –Panel/Wall/Desktop/VESA....................14
2.4.1 Panel Mounting.........................................................14
2.4.2 Wall-Mounting...........................................................15
2.4.3 Desktop-Mounting....................................................16
2.4.4 VESA-ARM Mounting...............................................18
2.5 Wireless Card Installation..........................................20
CHPATER 3 PHOENIX-AWARD BIOS UTILITY.............................23
3.1 Entering Setup...........................................................23
3.2 Control Keys..............................................................24
3.3 Getting Help...............................................................24
3.4 The Main Menu..........................................................25
3.5 Standard CMOS Setup Menu....................................26
3.6 Advanced BIOS Features..........................................28
3.7 Advanced Chipset Features......................................31
3.8 Integrated Peripherals...............................................32
3.9 Power Management Setup........................................37
3.10 PnP/PCI Configuration Setup....................................39
3.11 PC Health Status.......................................................41
3.12 Load Optimized Defaults...........................................42
3.13 Set Supervisor/User Password..................................43

vii
3.14 Save & Exit Setup......................................................44
3.15 Exit Without Saving...................................................45
CHAPTER 4 DRIVERS INSTALLATION..........................................46
4.1 System.......................................................................46
4.2 Touch Screen............................................................47
4.2.1 Specification (GOT-5840TL).....................................47
4.2.2 Driver Installation- Windows XP................................47
4.3 Embedded O.S..........................................................50
4.3.1 Windows XP Embedded............................................50
4.3.2 Windows CE.NET5.0................................................51
Appendix...........................................................................................52

viii
MEMO

GOT-5840TL User s Manual
Introduction 1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications
ofthe GOT-5840TL. Chapter 1 includes the following sections:
nGeneral Description
nSpecification
nDimensions
nI/O Outlets
nPackage List
1.1 General Description
The GOT-5840TL is a fan-less and compact-size touch panel
computer, equipped with an 8.4" TFTLCD displayand lowpower
consumption AMD LX800 processor with FSB 500MHz. The GOT-
5840TL supports Windows®XP, Windows®CE.NETand Windows®
XP embedded. The panel is able to install a CompactFlash™card
and provide a MiniPCI slot for wireless module.
lGOT-5840TL: 8.4”TFTSVGA Fanless Touch Panel
Computer
ØReliable and Stable Design
The GOT-5840TL adopts a fan-less cooling systemand a
CompactFlash™card, which makes it especiallysuitable for
vibration-heavyenvironments, best for the transportation,
shipping and industrial machinerymarkets.

GOT-5840TL User s Manual
Introduction
2
ØEmbedded O.S. Supported
The GOT-5840TL not onlysupports Windows®XP, but also
supports embedded OS, such as Windows®CE.NET, and
Windows®XP embedded. For storage device, the GOT-5840TL
supports CompactFlash™card.
ØIndustrial-grade Product Design
The GOT-5840TL has an incredible design to be used in different
industrial harsh environments.
lA fuse helps prevent over-voltage for power input.
lThe front bezel meets the IP65/NEMA4 standard.
lFor connecting other devices, the GOT-5840TL also features
several interfaces: USB, Ethernet, and RS-232/422/485.
1.2 Specifications
1.2.1 Main CPU Board
lCPU
nAMD LX800 processor 500 MHzonboard
lSystem Chipset
nAMD LX + CS5536AD
lBIOS
nPhoenix-Award BIOS, 4Mbit with RPL/PXE LAN boot ROM,
SmartViewand customer CMOS Backup
lSystem Memory
nOne 200-pin DDR DIMM socket
nMaximummemoryup to 1GB

GOT-5840TL User s Manual
Introduction 3
1.2.2 I/O System
lStandard I/O
nOne RS-232 and one RS-232/422/485
nTwo USB 2.0
lEthernet
nOne RTL8139DL Fast Ethernet
lAudio
nLine-out
lExpansion
nOne Mini-PCI
lStorage
nOne sloot for CF card
1.2.3 System Specification
l8.4 TFTLCD
lHeat Dispensing Design
lNet Weight
n1.3 Kgs (2.87 lb)
lDimension (Main BodySize)
n251x 44.6 x 205mm
lOperation Temperature
n0to 45
lRelative Humidity
n10% to 90% @ 40 , Non-Condensing
lVibration (Operating)
n5 to 500 Hz, 2.0 G random

GOT-5840TL User s Manual
Introduction
4
NOTE All specifications and images are subject to change
without notice.

GOT-5840TL User s Manual
Introduction 5
1.3 Dimensions
This diagramshows you dimensions and outlines ofthe GOT-5840TL.

GOT-5840TL User s Manual
Introduction
6

GOT-5840TL User s Manual
Introduction 7
1.4 I/O Outlets
Please refer to the following illustration for I/O locations oftheGOT-
5840TL.
No Function
1POWER SWITCH
224VDC POWER
3COM2 (RS-232)
4COM1 (RS-232/422/485)
51 XETHERNET (RJ-45)
62 XUSB 2.0
7AUDIO (LINE-OUT)

GOT-5840TL User s Manual
Introduction
8
1.5 Packing List
When you receive the GOT-5840TL, the bundled package should
contain the following items:
lGOT-5840TL x 1
lPanel Mount Kit x 6
lDriver CD x1
lWall-Mount Kit x1
lWireless LAN kit (optional)
lDesktop Stand Kit (optional)
lVESA ARM (optional)
Ifyou have anydemand for the optional items or anyitems are
missing, please contact AXIOMTEK distributors immediately.

GOT-5840TL User s Manual
Hardware Installation 9
CHAPTER 2
HARDWARE INSTALLATION
The GOT-5840TL provides rich I/O ports and flexible expansions for
you to meet different demand, for example, CF card. The chapter will
showyou howto install the hardware. It includes:
nCompactFlash™Card
nSerial Port
nEthernet
nMounting Way
2.1 CF Card Installation
The GOT-5840TL provides one CF slot for users to install
CompactFlash™card. Please refer to the following instructions for
installation:
Step 1 Turn off the system, and unplug the power cord.

GOT-5840TL User s Manual
Hardware Installation
10
Step 2 Find out the cover on the side ofthe system.
Step 3 Locate the CompactFlashTM socket, and insert the card into
the socket.

GOT-5840TL User s Manual
Hardware Installation 11
2.2 Serial Ports Interface
The GOT-5840TL has two onboard serial ports, COM1 (RS-
232/422/485) and COM2 (RS-232).
The following table shows you the pin assignments ofthis connector:
Pin
Signal Pin Signal
1 Data Carrier
Detect (DCD) 6 Data Set Ready
(DSR)
2 Receive Data
(RXD) 7 Request To Send
(RTS)
3 Transmit Data
(TXD) 8Clear To Send (CTS)
4 Data Terminal
Ready (DTR) 9Ring Indicator (RI)
5 Ground (GND)
In addition, COM1 can be set for RS-232/422/485 byjumper. The
jump setting is listed as below:
COM1 JP12 JP10 JP11
RS-232 (default) 1-2 3-5, 4-6 3-5, 4-6
RS-422 3-4, 7-8 1-3, 2-4 1-3, 2-4
RS-485 5-6, 7-8 1-3, 2-4 1-3, 2-4

GOT-5840TL User s Manual
Hardware Installation
12
When COM1 is set to RS-422 or RS-485, the pin assignments are
listed below:
Signal Name
Pin # RS-422 RS-485
1TX-DATA-
2TX+DATA+
3RX+No connector
4RX-No connector
5No connector No connector
6No connector No connector
7No connector No connector
8No connector No connector
9GND GND
COM2
COM1