AXIOMTEK GOT5153W-845 User manual

GOT5153W-845
All-in-One
15.6” WXGA TFT Fanless Touch Panel
Computer with Intel® Celeron® Processor
N3060 onboard
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2017 Axiomtek Co., Ltd.
All Rights Reserved
March 2017, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT5153W-845 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT5153W-845 Series
is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 General Description............................................................................2
1.2 Specifications......................................................................................3
1.3 Dimensions..........................................................................................5
1.4 I/O Outlets............................................................................................7
1.5 Packing List.........................................................................................9
Chapter 2 Hardware and Installation .................... 11
2.2 SBC87845 Jumpers and Connectors...............................................12
2.2.1 Jumper Settings ........................................................................................ 14
2.2.2 Connectors................................................................................................ 15
2.3 Ethernet..............................................................................................20
2.4 Mountings –Wall/Desktop/VESA.....................................................21
2.4.1 Wall-Mounting ........................................................................................... 21
2.4.2 Desktop-Mounting..................................................................................... 22
2.5 HDD Installation.................................................................................23
2.6 DRAM Installation..............................................................................26
2.7 Mini cards Card Installation..............................................................28
2.7.1 Wireless LAN Card Installation ................................................................. 28
2.7.2 mSATA Card Installation............................................................................ 30
2.8 Power Input (Phoenix type)..............................................................31
Chapter 3 AMI BIOS Setup Utility .......................... 32
3.1 Navigation Keys ................................................................................32
3.2 Main Menu..........................................................................................33
3.3 Advanced Menu.................................................................................34
3.4 Chipset Menu.....................................................................................41
3.5 Security..............................................................................................43
3.6 Boot Menu..........................................................................................44
3.7 Save & Exit.........................................................................................45
Chapter 4 Drivers Installation .............................. 47

v
4.1 System ...............................................................................................47
4.2 Touch Screen.....................................................................................48
4.2.1 Specification.............................................................................................. 48
4.3 Embedded O.S...................................................................................49
4.3.1 WES 7 & WE8S......................................................................................... 49
Appendix A Watchdog Timer................................... 51
About Watchdog Timer................................................................................51
How to Use Watchdog Timer.......................................................................51
WDT Sample Program .................................................................................52
How to Use DIO Software Programming....................................................53
Appendix B Volume Control .................................... 55
About Volume Control.................................................................................55
How to Use Volume Control........................................................................55
Removed Volume Control Tool...................................................................63

vi
This page is intentionally left blank.

GOT5153W-845 User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the GOT5153W-845.
Chapter 1 includes the following sections:
General Description
Specifications
Dimensions
I/O Outlets
Package List

GOT5153W-845 User’s Manual
2 Introduction
1.1 General Description
The GOT5153W-845 is a fan-less and compact-size touch panel computer, equipped with a
15.6”TFT LCD display, 5W flat resistive touch or project capacitive multi-touch for option and
low power consumption Intel® Celeron® Processor N3060. The GOT5153W-845 supports
Windows 7, Windows 8.x and Windows embedded OS. The panel computer is able to install a
mSATA and provide two Mini card slots for wireless module. Its excellent ID and friendly user
interface make it a professional yet easy-to-use panel computer. The GOT5153W-845 is an
ideal for space-limited applications in infotainment, factory automation, building automation,
and more.
GOT5153W-845: 15.6”TFT WXGA Fanless Touch Panel Computer
Reliable and Stable Design
The GOT5153W-845 adopts a fanless cooling system, which makes it suitable for
industrial environments.
Embedded O.S. Supported
The GOT5153W-845 not only supports Windows 7 and Windows 8.x, but also supports
embedded OS,. For storage device, the GOT5153W-845 supports 2.5”SATA device and
mSATA.
Industrial-grade Product Design
The GOT5153W-845 has an incredible design to be used in different industrial
environments.
The front bezel meets the IP65/NEMA4 standard.
For connecting other devices, the GOT5153W-845 also features several interfaces: USB,
Ethernet, and RS-232/422/485.

GOT5153W-845 User’s Manual
Introduction 3
1.2 Specifications
Main CPU Board
CPU
Onboard Intel® Celeron® Processor N3060 2C@1.6GHz, up to 2.48GHz
System Memory
One 204-pin DDR3L SO-DIMM socket
Maximum memory up to 8BG
BIOS
America Megatrends BIOS
I/O System
Standard I/O
One RS-232/422/485
One RS-232
Two USB 2.0
Two USB 3.0
One HDMI
Ethernet
2x RJ45 Giga Ethernet (Intel i211AT)
Audio
One Line out
Two Internal 3W speaker
Expansion
1 x Mini-card slot (w/SIM slot)
1 x Mini-card slot (supports mSATA)
Storage
One mSATA
One 2.5”SATA HDD (only in AC version)
Power connector
GOT5153W-845-FR-DC/GOT5153W-845-PCT-DC : 9VDC to 36VDC with phoenix
power connector or
GOT5153W-845-FR-J/GOT5153W-845-PCT-J: 12VDC w/external 60W AC Adapter
with screw type connector

GOT5153W-845 User’s Manual
4 Introduction
System Specification
15.6”WXGA(1366x768) LCD with LED backlight
Project capacitive multi-touch or 5 wired flat resistive touch
Fanless Heat Dispensing Design
Disk drive housing:
One 2.5”SATA drive (only in AC version)
Net Weight
3.0 Kgs (6.61 lb)
Dimension (Main Body Size)
394.2 mm x 57 mm x 257.2 mm
Operation Temperature
0℃to 45℃
Relative Humidity
10% to 90% @ 40℃, Non-Condensing
Vibration
2.0G, 5 to 500 Hz, 2.0 G random for SSD or mSATA
Power input
9~36VDC with phoenix power connector or
External 60W AC Adapter
—Power Input: 100VAC to 240VAC
—Power Output: 12VDC, Max. 5A
NOTE All specifications and images are subject to change without notice.
NOTE If the operation temperature is higher than 35 ℃ , the wide temperature
HDD is recommended to be used on the device.
NOTE If the operation temperature is higher than 45 ℃ , the wide temperature SSD are
recommended to be used on the device.

GOT5153W-845 User’s Manual
Introduction 5
1.3 Dimensions
This diagram shows you dimensions and outlines of the GOT5153W-845.

GOT5153W-845 User’s Manual
6 Introduction

GOT5153W-845 User’s Manual
Introduction 7
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT5153W-845.
No
Function
No
Function
1
POWER SWITCH (ATX)
8
COM 2(RS-232)
2
Power Input connector (Screw)
9
HDMI
3
Power Input connector (Phoenix)
10
Dual USB 3.0 ports
4
Speaker
11
Ethernet (RJ-45)
5
Dual USB 2.0 ports
12
AT/ATX selectable switch
6
Audio (Line-out)
13
Speaker
7
COM 1(RS-232/422/485)

GOT5153W-845 User’s Manual
8 Introduction
No
Function
No
Function
1
Power LED
orange: display off
green : display on
5
Display on/off
2
HDD LED
6
Volume -
3
Brightness -
7
Volume +
4
Brightness +
NOTE The volume control function only can be performed under the windows
operation system with AXIOMTEK volumeSYNC program.

GOT5153W-845 User’s Manual
Introduction 9
1.5 Packing List
When you receive the GOT5153W-845, the bundled package should contain the following
items:
GOT5153W-845 x 1
Driver CD x1
Screws for HDD x4 (DC version)
HDD mylar (DC version)
Phoenix connector x1 (DC version)
Power Adapter & power cord (AC adapter version)
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.

GOT5153W-845 User’s Manual
10 Introduction
This page is intentionally left blank.

GOT5153W-845 User’s Manual
Hardware and Installation 11
Chapter 2
Hardware and Installation
The GOT5153W-845 provides rich I/O ports and flexible expansions for you to meet different
demand. The chapter will show you how to install the hardware. It includes:
SBC87845 Jumpers and Connectors
Ethernet
Mounting Way
Hard disk
DRAM
Wireless LAN Card
Power Input

GOT5153W-845 User’s Manual
12 Hardware and Installation
2.2 SBC87845 Jumpers and Connectors
Component Side

GOT5153W-845 User’s Manual
Hardware and Installation 13
Solder Side

GOT5153W-845 User’s Manual
14 Hardware and Installation
2.2.1 Jumper Settings
Making the proper jumper settings configure the SBC87845 to match the needs of your
application.
The following table shows the default jumper settings for the onboard devices.
Jumper
★Default Setting
Jumper Setting
JP1
★OSD function: LCD ON/OFF
OSD function: Touch ON/OFF
Short 1-2
Short 2-3
JP2
★LVDS Panel Power : 3.3V
LVDS Panel Power : 5V
Short 1-2
Short 2-3
JP3
★ATX mode
AT mode
Short 1-2
Short 2-3
JP5
Touch Controller 4,8 WIRE
★Touch Controller 5 WIRE
Short 1-2
Short 2-3
JP6
★Normal
Clear CMOS
Short 1-2
Short 2-3
JP7
★Internal Buzzer enable
Internal Buzzer disable
Short 1-2
Short 2-3
JP8
★COM1 normal mode
COM1 pin1 with power :+5V
COM1 pin9 with power :+12V
Short 3-5,4-6
Short 1-3,4-6
Short 3-5,2-4