AXIOMTEK GOT3187W-832-PCT User manual

GOT3187W-832-PCT
All-in-One
18.5” WXGA TFT Fanless
Compact-Size
PANEL PC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
June 2013, Version A2
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT3187W-832-PCT Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT3187W-832-PCT
Series is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 Specifications......................................................................................2
1.3 Dimensions and Outlines ...................................................................4
1.4 I/O Outlets............................................................................................5
1.5 Packing List.........................................................................................6
Chapter 2 Hardware and Installation ...................... 7
2.1 CF card Installation.............................................................................8
2.2 Open back cover .................................................................................9
2.3 Serial Ports Interface ........................................................................10
2.3.1 COM1&COM2 Connector ..........................................................................11
2.4 Ethernet..............................................................................................12
2.5 Mountings: Panel / Wall / Desktop / VESA ......................................13
2.5.1 VESA-ARM/Wall-Mount ............................................................................ 13
2.5.2 Panel-mount Kit Assembly........................................................................ 14
2.6 HDD Installation.................................................................................15
2.7 DRAM Installation..............................................................................17
2.8 Wireless LAN Card Installation ........................................................19
2.9 Power .................................................................................................21
Chapter 3 AMI BIOS Setup Utility .......................... 23
3.1 Starting...............................................................................................23
3.2 Navigation Keys ................................................................................23
3.3 Main Menu..........................................................................................24
3.4 Advanced Menu.................................................................................25
3.5 Chipset Menu.....................................................................................32
3.6 Boot Menu..........................................................................................34
3.7 Security Menu....................................................................................35
3.8 Save & Exit Menu ..............................................................................36

v
Chapter 4 Drivers Installation................................ 39
4.1 System ...............................................................................................39
4.2 Touch Screen.....................................................................................39
4.3 Embedded O.S...................................................................................40

vi
This page is intentionally left blank.

GOT3187W-832-PCT User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the
GOT3187W-832-PCT. Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT3187W-832-PCT adopts a 18.5-inch WXGA TFT LCD with 300-nit brightness and an
Intel®AtomTM processor D2550 1.86 GHz to provide excellent computing performance and
thermal resistance. This fanless platform is especially designed for operating under
heavy-duty environment including steel refinery, oil pipe, ship, machine maker operating
systems and many more. Having below abilities makes GOT3187W-832-PCT surely a most
robust and cost-effective solution.
Wide Operating Temperature Range
GOT3187W-832-PCT features a technology of wide operating temperature range which allows
it to work between -10°C to +50°C. It incorporates compact ID and fanless cooling system with
a low power Intel®AtomTM processor D2550 1.86 GHz, making the platform a power-efficient
solution.
Reliable and Stable Design
The GOT3187W-832-PCT adopts a fan-less cooling system, which makes it especially
suitable for vibration-heavy environments, best for the transportation, ship, and industrial
machinery markets. For high capacity storage requirement, GOT3187W-832-PCT can work
under 2.0G (5 ~ 500Hz, random for CompactFlash ) in operation mode with a patent of
anti-vibration design. The patent improves the system reliability and sustainability.

GOT3187W-832-PCT User’s Manual
2 Introduction
WLAN Antenna Supported (optional)
GOT3187W-832-PCT has a PCI Express Mini Card slot for optional add-ons such as wireless
LAN card for 802.11 b/g connections & 3G/GPRS application, and more. It also provides an
optional fixed rotational WLAN antenna for wireless network connection.
More Features
GOT3187W-832-PCT utilizes one 204-pin DDR3 1066 SODIMM system memory max. up to
4GB, one SATA HDD and one CF. It provides over-current protection-fuse and a full set of I/O
including RS-232, RS-232/422/485, USB 2.0, audio (line-out), and Gigabit Ethernet.
Additionally, this slim unit supports panel mount, wall mount (optional), VESA mount (optional)
and desktop stand (optional).
1.2 Specifications
Main CPU Board
CPU
Intel○RAtomTM D2550 1.86GHz processor onboard
System Chipset
Intel○RNM10 Express
System Memory
One 204-pin DDR3 1066MHz SO-DIMM socket
Maximum memory up to 4GB
BIOS
America Megatrends BIOS
I/O System
Standard I/O
1 x RS-232/422/485, 1 x RS232
4 x USB 2.0
Ethernet
2 x RJ45 for Giga Ethernet
Audio
1x Line-out
Expansion
1 x Mini-card slot
Storage
1 x 2.5”SATA HDD
1 x CompactFlashTM Type II(optional)
Power connector
Phoenix power connector

GOT3187W-832-PCT User’s Manual
Introduction 3
System Specification
18.5”WXVGA(1366x768) LCD with LED backlight
PCT touch
Fanless Heat Dispensing Design
IP65 aluminum front bezel
Disk drive housing:
One 2.5”SATA drive
Net Weight
5.8 Kgs (11.02 lb)
Dimension (Main Body Size)
460.8x 58.5x 285 mm
Operation Temperature
-10℃to 50℃
Relative Humidity
20% to 90% @ 40℃, Non-Condensing
Power input
10~30VDC with phoenix power connector
NOTE All specifications and images are subject to change without notice.
NOTE If the operation temperature is higher than 40 ℃ , the wide temperature HDD/CF are
recommended to be used on the device.
NOTE If the operation temperature is higher than 45 ℃ , the wide temperature DRAM is
recommended to be used on the device.

GOT3187W-832-PCT User’s Manual
4 Introduction
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of GOT3187W-832-PCT

GOT3187W-832-PCT User’s Manual
Introduction 5
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT3187W-832-PCT.
No
Function
1
POWER SWITCH (ATX)
2
Terminal Block for DC Power Input
3
2xUSB 2.0
4
COM 1(RS-232/422/485)
5
COM 2(RS-232)
6
2xETHERNET
7
2xUSB2.0
8
Audio(Line-Out)

GOT3187W-832-PCT User’s Manual
6 Introduction
1.5 Packing List
When you receive the GOT3187W-832-PCT, the bundled package should contain the
following items:
GOT3187W-832-PCT unit x 1
Driver CD x1
Phoenix connector x 1
Panel mount kit x 12
Screws for HDD x 4
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.

GOT3187W-832-PCT User’s Manual
Hardware and Installation 7
Chapter 2
Hardware and Installation
The GOT3187W-832-PCT provides rich I/O ports and flexible expansions for you to meet
different demand, for example CF card. The chapter will show you how to install the hardware.
It includes:
CompactFlash™Card
Serial Port
Ethernet
Mounting Method
Hard disk
DRAM
Wireless LAN Card
Power

GOT3187W-832-PCT User’s Manual
8 Hardware and Installation
2.1 CF card Installation
The GOT3187W-832-PCT provides one CF slot for users to install CompactFlash™card.
Please refer to the following instructions for installation:
Step 1 Open the cover, unscrew 2 screws on the chassis.
Step 2 Stick the mylar on the CF card bottom side.

GOT3187W-832-PCT User’s Manual
Hardware and Installation 9
Step 3 Insert the CF card to the CF card slot, then finding the CF cover from the
system package and screw it.
2.2 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew 8 screws on the back cover. Please refer the photo below.

GOT3187W-832-PCT User’s Manual
10 Hardware and Installation
Step 2 Remove the back cover.
2.3 Serial Ports Interface
The GOT3187W-832-PCT has four serial ports. COM1 is RS-232/422/485 and COM2 is
RS-232. The following table shows you the pin assignments of this connector:
Jumper
Description
Jumper Setting
COM 1
RS-232 (Default)
JP8
JP7
JP9
RS-422
JP8
JP7
JP9
RS-485
JP8
JP7
JP9

GOT3187W-832-PCT User’s Manual
Hardware and Installation 11
2.3.1 COM1&COM2 Connector
The COM1 and COM2 is a standard DB-9 connector. This connector is equipped with
+5V level power capability on DCD and +12V level on RI by setting JP10 and JP11.
Jumper
Description
Default Jumper Setting
JP10
COM1 Port
W/O Power: (3-5, 4-6)
With Power: (1-3) DCD_+5V
(2-4) RI_+12V
(3-5, 4-6)
JP11
COM2 Port
W/O Power: (3-5, 4-6)(Default)
With Power: (1-3) DCD_+5V
(2-4) RI_+12V
(3-5, 4-6)
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If you
need COM1 port to support RS-422 or RS-485 mode, please refer to Jumper Settings
COM1 (SBC87832)
1 5
6 10
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
N.C
4
DTR
RX-
N.C.
5
GND
No use
No use
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use

GOT3187W-832-PCT User’s Manual
12 Hardware and Installation
2.4 Ethernet
The GOT3187W-832-PCT is equipped with a high performance Plug and Play Ethernet
interface, full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN
connector.
Please refer to detailed pin assignment list below:
Pin
Signal
1
2
3
4
5
6
7
8
RJ-45
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination

GOT3187W-832-PCT User’s Manual
Hardware and Installation 13
2.5 Mountings: Panel / Wall / Desktop / VESA
There are 4 application options for the GOT3187W-832-PCT, Panel/Wall/Desktop/VESA
mountings.
2.5.1 VESA-ARM/Wall-Mount
The GOT3187W-832-PCT provides VESA mount: 100x100 mm. Screw four screws to fix
the kit in the back chassis.
Wall mount:
VESA mount:

GOT3187W-832-PCT User’s Manual
14 Hardware and Installation
2.5.2 Panel-mount Kit Assembly
The GOT3187W-832-PCT is designed for panel mount application. To mount the
GOT3187W-832-PCT, the standard set of mounting kit (included in the system packaging)
is needed.