AXIOMTEK GOT5100T-845 User manual

GOT5100T-845
All-in-One
10.4” XGA/SVGATFT Fanless Touch Panel
Computer with Intel® Celeron® Processor
N3060 onboard
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness, or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery and dispose of used ones.
©Copyright 2021 Axiomtek Co., Ltd.
All Rights Reserved
May 2021, Version A2
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the GOT5100T-845 Series before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden
surge of power could ruin sensitive components. Make sure the GOT5100T-845 Series is
properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
◼Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
◼When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Section 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 Specifications......................................................................................2
1.3 Dimensions..........................................................................................4
1.4 I/O Outlets............................................................................................6
1.5 Packing List.........................................................................................7
Section 2 Hardware and Installation ...................... 9
2.1 SBC87845 Jumpers and Connectors...............................................10
2.1.1 Jumper Settings ........................................................................................ 12
2.1.2 Connectors................................................................................................ 13
2.2 Ethernet..............................................................................................18
2.3 Mountings –Panel/Wall/Desktop/VESA ..........................................19
2.3.1 Panel Mounting (optional) ......................................................................... 19
2.3.2 Wall-Mounting (optional) ........................................................................... 20
2.3.3 Desktop-Mounting..................................................................................... 20
2.3.4 VESA-ARM Mounting................................................................................ 22
2.4 HDD Installation ................................................................................23
2.5 DRAM Installation .............................................................................25
2.6 Mini cards Card Installation .............................................................27
2.6.1 Wireless LAN Card Installation ................................................................. 27
2.6.2 mSATA Card Installation............................................................................ 29
2.7 Power Input (Phoenix type)..............................................................30
Section 3 AMI BIOS Setup Utility .......................... 31
3.1 Navigation Keys ................................................................................31
3.2 Main Menu..........................................................................................32
3.3 Advanced Menu.................................................................................33
3.4 Chipset Menu.....................................................................................40
3.5 Security..............................................................................................42
3.6 Boot Menu..........................................................................................43
3.7 Save & Exit.........................................................................................44

v
Section 4 Drivers Installation .............................. 45
4.1 System ...............................................................................................45
4.1.1 Driver Content........................................................................................... 45
4.2 Touch Screen.....................................................................................46
4.2.1 Specification.............................................................................................. 46
4.2.2 Driver Installation- Windows 7/8.x............................................................. 47
4.3 Embedded O.S...................................................................................49
4.3.1 WES 7 & WE8S......................................................................................... 49
Appendix A Watchdog Timer & DIO Programming ... 51
About Watchdog Timer................................................................................51
How to Use Watchdog Timer.......................................................................51
WDT Sample Program .................................................................................52
How to Use DIO Software Programming....................................................53

vi
This page is intentionally left blank.

GOT5100T-845 User’s Manual
Introduction 1
Section 1
Introduction
This chapter contains general information and detailed specifications of the GOT5100T-845.
Chapter 1 includes the following sections:
⚫General Description
⚫Specifications
⚫Dimensions
⚫I/O Outlets
⚫Package List
1.1 General Description
The GOT5100T-845 is a fan-less and compact-size touch panel computer, equipped with a
10.4”TFT LCD display and low power consumption Intel® Celeron® Processor N3060 (2M
Cache, up to 2.48 GHz). The GOT5100T-845 supports Windows 7, Windows 8.x, Windows 10
and Windows embedded OS. The panel computer is able to install mSATA and provide two
Mini card slots for wireless module. Its excellent ID and friendly user interface make it a
professional yet easy-to-use panel computer. The GOT5100T-845 is an ideal for space-limited
applications in factory automation, machine maker operating systems, building automation,
and more.
GOT5100T-845: 10.4” TFT XGA/SVGA Fanless Touch Panel Computer
◼Reliable and Stable Design
The GOT5100T-845 adopts a fanless cooling system, which makes it suitable for
vibration environments.
◼Embedded O.S. Supported
The GOT5100T-845 not only supports Windows 7 and Windows 8.x, but also supports
embedded OS. For storage device, the GOT5100T-845 supports a 2.5”SATA device and
a mSATA.
◼Industrial-grade Product Design
The GOT5100T-845 has an incredible design to be used in different industrial
environments.
The front bezel meets the IP65/NEMA4 standard.
For connecting other devices, the GOT5100T-845 also features several interfaces: USB,
Ethernet, and RS-232/422/485.

GOT5100T-845 User’s Manual
2 Introduction
1.2 Specifications
Main CPU Board
⚫CPU
◼Intel® Celeron® Processor N3060 (2M Cache, up to 2.48 GHz) onboard.
⚫System Memory
◼One 204-pin DDR3L-1600 SO-DIMM socket
◼Maximum memory up to 8BG
⚫BIOS
◼America Megatrends BIOS
I/O System
⚫Standard I/O
◼One RS-232/422/485
◼One RS-232
◼Two USB 2.0
◼Two USB 3.0
⚫Ethernet
◼2x RJ45 Giga Ethernet (Intel i211AT)
⚫Audio
◼One Line out
⚫Expansion
◼1 x Mini-card slot (w/SIM slot)
◼1 x Mini-card slot (supports mSATA, optional)
⚫Storage
◼One mSATA
◼One 2.5”SSD
⚫Power connector
◼GOT5100T-845-J: 12VDC w/external 60W AC Adapter with screw type connector or
◼GOT5100T-845-24VDC: 24VDC with phoenix power connector

GOT5100T-845 User’s Manual
Introduction 3
System Specification
⚫10.4”XGA/SVGA (1024x768/800x600) LCD with LED backlight
⚫5 wired Resistive Touch
⚫Fanless Heat Dispensing Design
⚫Disk drive housing:
◼One 2.5”SATA drive
⚫Net Weight
◼1.8 Kgs (3.96 lb)
⚫Dimension (Main Body Size)
◼292.5 x 45.8 x 235.8 mm
⚫Operation Temperature
◼0℃to 50℃
⚫Relative Humidity
◼10% to 90% @ 40℃, Non-Condensing
⚫Vibration
◼2.0G, 5 to 500 Hz, random for SSD
⚫Power input
◼24VDC with phoenix power connector or
◼External 60W AC Adapter
—Power Input: 100VAC to 240VAC
—Power Output: 12VDC, Max. 5A
◼
NOTE All specifications and images are subject to change without notice.
NOTE If the operation temperature is higher than 35 ℃ , the wide temperature
HDD is recommended to be used on the device.

GOT5100T-845 User’s Manual
4 Introduction
1.3 Dimensions
This diagram shows you dimensions and outlines of the GOT5100T-845.

GOT5100T-845 User’s Manual
Introduction 5

GOT5100T-845 User’s Manual
6 Introduction
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT5100T-845.
No
Function
No
Function
1
POWER SWITCH (ATX)
7
COM 2(RS-232)
2
Power Input connector (Screw)
8
HDMI
3
Power Input connector (Phoenix)
9
Dual USB 3.0 ports
4
Dual USB 2.0 ports
10
Ethernet (RJ-45)
5
AUDIO (LINE-OUT)
11
AT/ATX selectable switch
6
COM 1(RS-232/422/485)

GOT5100T-845 User’s Manual
Introduction 7
1.5 Packing List
When you receive the GOT5100T-845, the bundled package should contain the following
items:
⚫GOT5100T-845 x 1
⚫HDD sponge x4
⚫Phoenix connector x1 (for GOT5100T-845-24VDC)
⚫Power Adapter & power cord (for GOT5100T-845-J)
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.
CAUTION ： There are 4 pieces of HDD sponge in packing list when shipment without HDD/SDD
pre-installed.

GOT5100T-845 User’s Manual
8 Introduction
This page is intentionally left blank.

GOT5100T-845 User’s Manual
Hardware and Installation 9
Section 2
Hardware and Installation
The GOT5100T-845 provides rich I/O ports and flexible expansions for you to meet different
demands. The chapter will show you how to install the hardware. It includes:
⚫SBC87845 Jumpers and Connectors
⚫Ethernet
⚫Mounting Way
⚫Hard disk
⚫DRAM
⚫Wireless LAN Card
⚫Power Input

GOT5100T-845 User’s Manual
10 Hardware and Installation
2.1 SBC87845 Jumpers and Connectors
Component Side

GOT5100T-845 User’s Manual
Hardware and Installation 11
Solder Side

GOT5100T-845 User’s Manual
12 Hardware and Installation
2.1.1 Jumper Settings
Making the proper jumper settings configure the SBC87845 to match the needs of your
application.
The following table shows the default jumper settings for the onboard devices.
Jumper
★Default Setting
Jumper Setting
JP1
★OSD function: LCD ON/OFF
OSD function: Touch ON/OFF
Short 1-2
Short 2-3
JP2
★LVDS Panel Power: 3.3V
LVDS Panel Power: 5V
Short 1-2
Short 2-3
JP3
★ATX mode
AT mode
Short 1-2
Short 2-3
JP5
Touch Controller 4,8 WIRE
★Touch Controller 5 WIRE
Short 1-2
Short 2-3
JP6
★Normal
Clear CMOS
Short 1-2
Short 2-3
JP7
★Internal Buzzer enable
Internal Buzzer disable
Short 1-2
Short 2-3
JP8
★COM1 normal mode
COM1 pin1 with power: +5V
COM1 pin9 with power: +12V
Short 3-5,4-6
Short 1-3,4-6
Short 3-5,2-4

GOT5100T-845 User’s Manual
Hardware and Installation 13
2.1.2 Connectors
The connectors allow the CPU Board to connect with other parts of the system. Ensure that all
connectors are in place and firmly attached. The following table lists the function of each
connector on the SBC87845
Connectors
Label
LVDS inverter connector
CN1
LVDS connector
CN2
SATA connector
CN3
OSD connector
CN4
HDD power connector
CN6
Full size min-PCIe connector
CN7, CN11
SIM card connector
CN8
DIO connector
CN9
Power connector
CN10
Power Button connector
CN12
Touch connector
CN13
LIN/MIC In connector
CN16
Speaker Out connector
CN17
System Fan connector
CN18
USB2.0 connector
CN19
RJ45 connector
CN20, CN22
USB3.0 connector
CN21
HDMI connector
CN23
Audio out connector
CN24
RS232/422/485 Port connector
CN25, CN27
RS232 Port connector
CN26
+5V Standby Power connector
CN28, CN29
LVDS inverter connector: CN1
Pin
Description
Pin
Description
1
GND
5
Inverter ON-OFF
2
GND
6
+12V
3
GND
7
+12V
4
Backlight control
8
+12V

GOT5100T-845 User’s Manual
14 Hardware and Installation
LVDS connector: CN2
Pin Assignment
Pin
Description
Pin
Description
1
VCC
21
GND
2
VCC
22
GND
3
VCC
23
LVDSA_DATAN0
4
VCC
24
LVDSB_DATAN2
5
VCC
25
LVDSA_DATAP0
6
VCC
26
LVDSB_DATAP2
7
Resolution selection [0]
27
GND
8
Resolution selection [1]
28
GND
9
GND
29
LVDSA_DATAN1
10
GND
30
LVDSA_DATAN3
11
LVDSB_DATAN3
31
LVDSA_DATAP1
12
LVDSB_DATAN0
32
LVDSA_DATAP3
13
LVDSB_DATAP3
33
GND
14
LVDSB_DATAP0
34
GND
15
GND
35
LVDSA_DATAN2
16
GND
36
LVDSA_CLKN
17
LVDSB_CLKN
37
LVDSA_DATAP2
18
LVDSB_DATAN1
38
LVDSA_CLKP
19
LVDSB_CLKP
39
Resolution selection [2]
20
LVDSB_DATAP1
40
Resolution selection [3]