AXIOMTEK Dk3g4PANEL 6153-O/P User manual

Dk3g4PANEL 6153-O/P
15” INDUSTRIAL TFT LCD MONITOR
User’s Manual

ii
Disclaimers
The information in this manual has been carefully checked and is believed to be
accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of
patents or other rights of third parties, which may result from its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in
this document.AXIOMTEK makes no commitment to update or to keep current the
information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of AXIOMTEK Co.,
Ltd.
©Copyright 2006 by AXIOMTEK Co. Ltd.,
All rights reserved.
June 2006, Version A1
Printed in Taiwan

iii
Safety Approvals
 CEMarking
 FCCClassA
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.

iv
Safety Precautions
Before getting started, read the following important cautions.
1. The P6153 does not come equipped with an operating system. An
operating system must be loaded first before installing any software
into the computer.
2. Be sure to ground yourself to prevent static charge when installing
the internal components. Use a grounding wrist strap and place all
electronic components in any static-shielded devices. Most
electronic components are sensitive to static electrical charge.
3. Disconnect the power cord from the P6153 before making any
installation. Be sure both the system and the external devices are
turned OFF. Sudden surge of power could ruin sensitive components.
Make sure the P6153 is properly grounded.
4. The brightness of the flat panel display decreases with usage.
However, hours of use vary depending on the application
environment.
5. Turn OFF the system power before cleaning. Clean the system using
a cloth only. Do not spray any liquid cleaner directly onto the screen.
The P6153 may come with or without a touchscreen. Although the
touchscreen is chemical resistant, it is recommended that you spray
the liquid cleaner on a cloth first before wiping the screen. In case
your system comes without the touchscreen, you must follow the
same procedure and not spray any cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen. Scratches on
the touchscreen may cause malfunction or internal failure to the
touchscreen.
7. The flat panel display is not susceptible to shock or vibration. When
assembling the P6153, make sure it is securely installed.

v
8. Do not open the system’s back cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do so.
Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:

Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity on
your body.
 When handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.

vi
This page does not contain any information.

Table of Contents vii
Table of Contents
Chapter 1 Introduction ..................... 1
1.1 General Description...........................................1
1.2 Features ............................................................. 2
1.3 Specifications....................................................2
1.4 Dimensions ........................................................3
1.5 I/O Inputs ...........................................................5
Chapter 2 System Setup..................... 7
2.1 System Configuration........................................ 7
2.2 Panel Mounting..................................................9
2.3 Wall Mounting (Option).................................... 11
2.4 Rack Mounting (Option)................................... 13
2.5 Desktop Stand (Option)................................... 14
Appendix A Supported Input Timing
Modes ........................... 16
Appendix B OSD Operation ............... 17

viii
This page does not contain any information.

Introduction 1
C h a p t e r 1
Introduction
This chapter contains the general information and the detailed
specifications of the P6153-O/P. Chapter 1 includes the following
sections:
 General Description

Features
 System Specification
 Dimensions

I/O Inputs
1.1 General Description
The Panel6153, a industrial 15.0 inches view area LCD Monitor
comes with slim, light and reliable features to replace traditional bulky
CRT for industrial application. Its unique front side design is fit for
open frame mounting (Panel6153-O) or panel mounting
(Panel6153-P). The display interface offers VGA-in, DVI, S-Video,
Video standard interfaces for different input source from PC system or
multimedia system that let you upgrade the display don’t change
anything from your system. Besides, for varied HMI field, you can
choose one of resistive, capacitive touch screen or glass interface to
meet your application. In addition, this monitor has more comfort,
safety, and environmental protection for humanized & health
consideration those would be the benefit that users can get.
This LCD monitor builds in 15.0” color active matrix thin-film-transistor
(TFT) liquid crystal display to provide superior display performance. A
maximum resolution of 1024x768 is ideal for displaying complex
graphics and high definition images. Other outstanding designs that
enhance this LCD monitor ’s performance are Plug & Play
compatibility, and OSD (On Screen Display) controls, especially OSD,
it made you ease adjustment on screen image.

2
1.2 Features
 High contrast color 15.0” SXGA TFT LCD display support
resolution up to 1024x768
 Heavy-duty steel chassis with NEMA4/IP65-compliant

Suits with resistive, capacitive or tempered
anti-reflection glass
 Multi-scan function supports XGA, SVGA, VGA,
VGA-Text, PC-9801, MAC.

High Brightness and Ultra-wide viewing angle with
anti-glare features
 Power management system conforms to VESA DPMS
standard

Advanced OSD control for picture quality adjustment
 Supports VESA ARMS, Desktop Stand

Rear, Panel, Wall or Rack mounting
1.3 Specifications

Construction: Heavy-duty steel chassis

Control: OSD (On Screen Display) control pad on front
side
 Mounting: Support Panelmount, VESA arm mounting,
Rackmount(optional), and Wallmount(optional)
 Net weight: 5.1Kgs for P6153PR
 Dimension (main body size):
- P6153-P
400.0X323.0X45.5 mm
- P6153-O
400.0X323.0X45.5 mm

Operating Temperature Range: 0oC ~ 50oC

Relative Humidity: 20% ~ 90%; non-condensing