AXIOMTEK P6125 User manual

P6125
12.1” XGA TFT Railway Monitor
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
Copyright 2018 Axiomtek Co., Ltd.
All Rights Reserved
Nov 2018, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the P6125 Series before making any installation. Be
sure both the system and the external devices are turned OFF. Sudden surge of power
could damage sensitive components. Make sure the P6125 Series is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on a human body.
When handling boards and components, wear a grounding wrist strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
AMI is a trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers......................................................................................................i
Safety Precautions........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 General Description ............................................................................1
1.2 Features ...............................................................................................2
1.3 Specifications......................................................................................2
1.4 Dimensions and Outlines ...................................................................3
1.5 I/O Outlets ............................................................................................4
1.6 Packing List .........................................................................................5
Chapter 2 System Setup .......................................... 7
2.1 System Configuration .........................................................................8
2.2 Panel Mounting ...................................................................................9
2.3 VESA Mounting ...................................................................................9
2.4 I/O PIN ASSIGNMENT........................................................................10
2.4.1 DC power Jack w/ M12 connector, 24~110VDC power input ................... 10
2.4.2 Waterproof Power Cable ........................................................................... 10
2.4.3 VGA PORT .................................................................................................11
2.4.4 RS 232 PORT, support multi-function of T/S and remote. .........................11
2.4.5 Y cable for RS-232 to resistive touch and remote .................................... 12
2.4.6 HDMI PORT .............................................................................................. 13
2.4.7 DVI-D PORT.............................................................................................. 13
Appendix A Supported Input Timing Modes ............. 15
Appendix B OSD Operation........................................ 17
Function Description of OSD Menu............................................................17
Appendix C AD Board Management System ............. 19

P6125 User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the P6125. Chapter 1
includes the following sections:
General Description
Features
Specifications
Dimensions and Outlines
I/O Outlets
Package List
1.1 General Description
The P6125 is a 12.1-inch view area industrial LCD monitor that incorporates a slim, lightweight
display to replace traditional bulky CRT monitors for Industrial applications, with a unique flat
design specifically suited for panel mounting and VESA mounting. Its display interface
supports DVI-D and HDMI digital input as well as VGA input for different input sources from PC
systems or multimedia devices, allowing you to upgrade the display without having to change
anything from your system. Protected by an anti-vibration design, its rugged HMI
(human-machine interface) also works well on the train.
This LCD monitor features a color active matrix thin-film-transistor (TFT) liquid crystal display
with 800 nits brightness and a maximum resolution of 1024x768, providing superior display
performance and making the monitor ideal for presenting complex graphics and high definition
images. Other outstanding designs that enhance the monitor’s performance include its plug &
play compatibility and OSD (On Screen Display) controls, which, in particular, allow you to
adjust on-screen images with ease.

P6125 User’s Manual
2 Introduction
1.2 Features
High contrast color 12.1”XGA TFT LCD display with supported resolution up to
1024x768
Auto-dimming for different lighting environments
Flat design with NEMA4/IP65 compliance
Suitable for resistive touch
High Brightness and ultra-wide viewing angle with anti-glare features.
Power management system that conforms to VESA standard
Advanced OSD control for picture quality adjustment
Provide remote control for OSD adjustment (refer to Appendix C)
1.3 Specifications
12.1” XGA(1024x768) LCD with LED backlight
Resistive touch
Front bezel design with NEMA4/IP65 compliance
Control: OSD (on-screen display) control pad on the side
Mounting: Supports panel mount and VESA arm mount
Net weight
P6125: 2.2 KGS
Dimension (main body size)
P6125: 330 x 245 x 57 mm
Operation temperature
-25°C to 55°C
Relative humidity
20% to 90% @ 40°C, Non-condensing
Power input
wide range 24~110VDC power input
Max power consumption: 33W
Audio
3W speaker x 2
Line-in for audio input from VGA / DVI-D
NOTE: All specifications and images are subject to change without notice.

P6125 User’s Manual
Introduction 3
1.4 Dimensions and Outlines
The following diagrams show the dimensions and outlines of the P6125.

P6125 User’s Manual
4 Introduction
1.5 I/O Outlets
Please refer to the following illustrations for I/O locations of the P6125.
I/O outlets with VGA input and speaker
No
Function
No
Function
1
Menu (Enter function)
8
Touch & remote control via RS-232
2
SEL+
9
VGA
3
SEL-
10
HDMI
4
Menu Exit / Input Switch
11
DVI-D
5
Status LED
12
Line-in
6
Power switch
13
Speaker
7
DC power input

P6125 User’s Manual
Introduction 5
1.6 Packing List
When you receive the P6125 VGA input version, the bundled package should contain the
following items:
P6125 unit x 1
VGA cable x 1
RS-232 cable x1 (for resisitve touch)
If you request a cable assembly for resistive touch and remote control, please refer to section
2.4: I/O Pin Assignment.
If you cannot find the package or any items are missing, please contact Axiomtek distributors
immediately.

P6125 User’s Manual
6 Introduction
This page is intentionally left blank.

P6125 User’s Manual
System Setup
7
Chapter 2
System Setup
This chapter details the system parts and components with figures. Sections include:
System Configuration
Panel Mounting
VESA Mounting
I/O Pin Assignment
DC power
Waterproof power cable
VGA port
RS-232 port: supports multi-function of T/S and remote
Y cable for RS-232 to resistive touch and remote
HDMI port
DVI-D port

P6125 User’s Manual
8 System Setup
2.1 System Configuration
The figure below shows the side views of the P6125 series.
1. Menu:
Press this button to turn on/off the OSD (on-screen display) main menu.
Press this button to activate selected items.
2. SEL+:
To scroll up the menu.
To increase the value of a selected item.
3. SEL-:
To scroll down the menu.
To decrease the value of a selected item.
4. Exit: menu exit / input switc
When the menu is on the screen, short press for Jump out selection icon.
When the menu is not on the screen, long press for input switch (VGA->HDMI->DVI-D).
When the menu is not on the screen, short press for Auto Adjust (VGA only).
5. Status LED:
The light is green when the power is on; red light appears when the monitor goes into
standby mode.
6. Power switch:
Press this button to turn on/off the monitor.

P6125 User’s Manual
System Setup
9
2.2 Panel Mounting
The P6125 is designed for panel mount applications. To mount the P6125, locate the standard
holes on the front of P6125.
2.3 VESA Mounting
The P6125 provides VESA mount at the back of system. Screw four screws to fix the kit in the
back chassis.

P6125 User’s Manual
10 System Setup
2.4 I/O Pin Assignment
The P6125 comes with a DC-in connector, T/S port, HDMI port, DVI-D port, and Line-In port.
Please refer to following information for detailed pin assignment.
2.4.1 DC power jack w/ M12 connector, 24~110VDC power input
2.4.2 Waterproof power cable
Please follow the pin assignment for the power input.
Pin
Signal
V+
power input
Earth ground
GND
GND
GND
GND
Pin
Signal
1. V+
power input
2. V+
power input
3
GND
4
GND
5
Earth ground

P6125 User’s Manual
System Setup 11
2.4.3 VGA port
Pin
Define
Pin
Define
Pin
Define
1
Red
6
Red GND
11
N.C.
2
Green
7
Green GND
12
DDC Data
3
Blue
8
Blue GND
13
H-Sync
4
N.C.
9
+5V (In)
14
V-Sync
5
Ground
10
Ground
15
DDC Clock
2.4.4 RS 232 port: supports multi-functions of T/S and remote
Pin
Define
Pin
Define
1
Remote RXD
6
Touch DTR
2
Touch TXD
7
Touch RTS
3
Touch RXD
8
Remote TXD
4
Touch DSR
9
N.C.
5
Ground

P6125 User’s Manual
12 System Setup
2.4.5 Y cable for RS-232 to resistive touch and remote
DB9: connects to P6125
DB9 male: connects to P6125
Pin
Define
Pin
Define
1
Remote RXD
6
Touch DTR
2
Touch TXD
7
Touch RTS
3
Touch RXD
8
Remote TXD
4
Touch DSR
9
N.C.
5
Ground
DB9 female: connects to PC for touch
Pin
Define
Pin
Define
1
N.C.
6
Touch DTR
2
Touch TXD
7
Touch RTS
3
Touch RXD
8
N.C.
4
Touch DSR
9
N.C.
5
Ground
DB9 female: connects to PC for remote
Pin
Define
Pin
Define
1
N.C.
6
N.C.
2
Remote RXD
7
N.C.
3
Remote TXD
8
N.C.
4
N.C.
9
N.C.
5
Ground

P6125 User’s Manual
System Setup 13
2.4.6 HDMI port
Pin
Define
Pin
Define
Pin
Define
1
TMDS2+
8
GND
15
DDC clock
2
Cable Detect
(GND)
9
TMDS0-
16
DDC date
3
TMDS2-
10
TMDS clock+
17
GND
4
TMDS1+
11
GND
18
Vin (+5V)
5
GND
12
TMDS clock-
19
Hot plug detect
6
TMDS1-
13
N.C.
7
TMDS0+
14
N.C.
2.4.7 DVI-D port
Pin
Define
Pin
Define
Pin
Define
Pin
Define
1
TMDS2−
7
DDC data
13
N.C.
19
GND
2
TMDS2+
8
N.C.
14
Vin (+5V)
20
N.C.
3
GND
9
TMDS1-
15
GND
21
N.C.
4
N.C.
10
TMDS1+
16
Hot plug detect
22
GND
5
N.C.
11
GND
17
TMDS0-
23
TMDS clock+
6
DDC clock
12
N.C.
18
TMDS0+
24
TMDS clock−

P6125 User’s Manual
14 System Setup
This page is intentionally left blank.

P6125 User’s Manual
Supported Input Timing Modes 15
Appendix A
Supported Input Timing Modes
SPEC
MODE
Pixel
Freq.
Horizontal Timing
Vertical Timing
Sync
Polar
Freq.
Total
Active
Sync
Polar
Freq.
Tota
l
Active
MHZ
KHz
Pixel
Pixel
Hz
Line
Line
640×480
@60Hz
25.175
VESA
N
31.469
800
640
N
59.940
525
480
640×480
@60Hz
25.175
VESA
N
31.469
800
640
N
59.940
525
480
800×600
@60Hz 0
40.000
VESA
P
37.879
1056
800
P
60.317
628
600
SPEC
MODE
Pixel
Freq.
Horizontal Timing
Vertical Timing
Sync
Polar
Freq.
Total
Active
Sync
Polar
Freq.
Total
Active
MHZ
KHz
Pixel
Pixel
Hz
Line
Line
1024×768
@60Hz
65.000
VESA
N
48.363
1344
1024
N
60.005
806
768
NOTE: Timing depends on LCD panel requirements.

P6125 User’s Manual
16 Supported Input Timing Modes
This page is intentionally left blank.