AXIOMTEK P6187W-V3 User manual

P6187W-V3
18.5” WXGA TFT Monitor
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make
any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
©Copyright 2021 Axiomtek Co., Ltd.
All Rights Reserved
September 2021, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the P6187W-V3 Series before making any installation.
Be sure both the system and the external devices are turned OFF. Sudden surge of
power could ruin sensitive components. Make sure the P6187W-V3 Series is properly
grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
◼Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
◼When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Section 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 Features...............................................................................................2
1.3 Specifications......................................................................................2
1.4 Dimensions and Outlines ...................................................................3
1.5 I/O Outlets............................................................................................4
1.6 Packing List.........................................................................................5
Section 2 System Setup .......................................... 7
2.1 System Configuration.........................................................................7
2.2 Panel Mounting ...................................................................................8
2.3 Wall Mounting......................................................................................8
2.4 VESA Mounting ...................................................................................8
2.5 OSD Key Configuration ......................................................................9
Press this button to turn on/off the monitor................................................9
Appendix A Supported Input Timing Modes ............. 10
Appendix B OSD Operation........................................ 12
Function Description of OSD Menu............................................................12

P6187W-V3 User’s Manual
Introduction 1
Section 1
Introduction
This chapter contains general information and detailed specifications of the P6187W-V3.
Chapter 1 includes the following sections:
⚫General Description
⚫Features
⚫Specifications
⚫Dimensions and Outlines
⚫I/O Outlets
⚫Package List
1.1 General Description
The P6187W-V3, an industrial 21.5 inches view area LCD Monitor comes with slim, light and
reliable features to replace traditional bulky CRT for Industrial application. Its unique flat
design is fit for panel mounting, VESA mounting, Wall mounting and Rack mounting. The
display interface offers DVI-D, HDMI and VGA for different input source from PC system or
multimedia system that let you upgrade the display don’t change anything from your system.
Besides, for varied HMI field, you can choose one of resistive touch or glass interface to meet
your application. In addition, this monitor has more comfort, safety, and environmental
protection for humanized & health consideration those would be the benefit that users can get.
This LCD monitor builds in color active matrix thin-film-transistor (TFT) liquid crystal display to
provide superior display performance. A maximum resolution of 1920x1080 is ideal for
displaying complex graphics and high definition images. Other outstanding designs that
enhance this LCD monitor’s performance are Plug & Play compatibility, and OSD (On Screen
Display) controls, especially OSD, it made you ease adjustment on screen image.

P6187W-V3 User’s Manual
2 Introduction
1.2 Features
⚫High contrast color 18.5”WXGA TFT LCD display support resolution up to
1366 x768
⚫Flat design with NEMA4/IP65-compliant
⚫Suits with Projected capacitive touch
⚫High Brightness and Ultra-wide viewing angle
⚫Power management system conforms to VESA DPMS standard
⚫Advanced OSD control for picture quality adjustment
⚫Supports VESA ARMs, Desktop Stand Rear, Panel, Wall mounting
1.3 Specifications
⚫18.5”WXGA(1366 x 768) LCD with LED backlight
⚫Projected capacitive touch or glass
⚫Front bezel design with NEMA4/IP65
⚫Control: OSD (On Screen Display) control pad on the side
⚫Mounting: Support Panel mount, VESA arm mount and Wall mount (optional)
⚫Net/Gross Weight
◼P6187W-V3: 7.56KG / 8.92KG
⚫Dimension (Main Body Size)
◼P6187W-V3: 460.0 mm (18.11") (W) x 285.0 mm (11.22") (H) x 56.2 mm (2.21") (D)
⚫Operation Temperature
◼0℃to 50℃
⚫Relative Humidity
◼10% to 90% @ 40℃, Non-Condensing
⚫Power input
◼DC Version: Terminal block (24Vdc)
◼Max power consumption: 20W
NOTE: 1. All specifications and images are subject to change without notice.
2. If vibration is over 1GHz, LCD will have twinkle that is a normal phenomenon.
When the vibration of system goes back 1GHz, the twinkle would disappear.

P6187W-V3 User’s Manual
Introduction 3
1.4 Dimensions and Outlines
The following diagrams show the dimensions and outlines of P6187W-V3
P6187W-V3:
(AC Version by project)

P6187W-V3 User’s Manual
4 Introduction
1.5 I/O Outlets
Please refer to the following illustration for I/O locations of the P6187W-V3.
No
Function
No
Function
1
Menu (Enter function)
4
Exit/Auto Adjust
2
SEL+
5
Power LED
3
SEL-
6
Power Switch

P6187W-V3 User’s Manual
Introduction 5
1.6 Packing List
When you receive the P6187W-V3, the bundled package should contain the following items:
⚫P6187W-V3 unit x 1
⚫VGA cable x1
⚫USB cable cable x1 (for touch version only )
⚫Panel mount kit set x 1 (optional)
⚫HDMI cable x1(optional)
⚫DP cable x1 (optional)
⚫Wall mount bracket x1 (optional)
If you cannot find the package or any items are missing, please contact Axiomtek distributors
immediately.

P6187W-V3 User’s Manual
6 Introduction
This page is intentionally left blank.

P6187W-V3 User’s Manual
System Setup
7
Section 2
System Setup
This chapter details the system parts and components with figures. Sections include:
⚫System Configuration
⚫Panel Mounting
⚫Wall Mounting
⚫VESA Mounting
2.1 System Configuration
The figure below shows the side views of P6187W-V3 series.
1. Exit:
Jump out the selection icon / Auto adjust.
2. Menu:
Press this button to turn on/off the OSD (On Screen Display) main menu.
Press this button to activate selected items.
3. SEL-:
To scroll down the menu to decrease the value of selected item.
4. SEL+:
To scrolling up the menu to increase the value of selected item.
5. Power LED:
When the light is green, the power is on, red light when stand by.
6. Power switch:
Press this button to turn on/off the monitor.

P6187W-V3 User’s Manual
8 System Setup
2.2 Panel Mounting
The P6187W-V3 is designed for panel mount application. To mount the P6187W-V3, the
standard set of mounting kit (included in the system packaging) is needed.
▲P6187W-V3 Panel Mount kits
2.3 Wall Mounting
The P6187W-V3 provides VESA mount and wall mount. Screw four screws to fix the kit in the
back chassis.
2.4 VESA Mounting
The P6187W-V3 provides VESA mount at the back of system. Screw four screws to fix the kit

P6187W-V3 User’s Manual
System Setup
9
in the back chassis.
2.5 OSD Key Configuration
1. Menu: a. Press this button to turn on/off the OSD (On Screen Display) main menu.
b. Press this button to activate selected items.
2. SEL+: a. To scroll up the menu.
b. To increase the value of selected item.
3. SEL‐: a. To scroll down the menu.
b. To decrease the value of selected item.
4. Exit: a. Jump out the selection icon.
b. Auto adjust.
5. Power LED:
When the indicator light is green, it means there is a signal, and it lights up red
When there is no signal.
6. Monitor Power switch:
Press this button to turn on/off the monitor

P6187W-V3 User’s Manual
10 Supported Input Timing Modes
Appendix A
Supported Input Timing Modes
Supported Input Timing Modes
Pixel Format
Refresh Rate
Standard Type
NOTE
640*480
60 Hz
Industry Standard
75 Hz
VESA Standard
800*600
60 Hz
VESA Guidelines
75 Hz
VESA Standard
1024*768
60 Hz
VESA Guidelines
75 Hz
VESA Standard
1280*1024
60 Hz
VESA Standard
70 Hz
VESA Standard
75 Hz
VESA Standard
1360*768
60 Hz
VESA Standard
75 Hz
VESA Standard
1920*1080
60 Hz
CEA Standard
NOTE: Timing depends on LCD Panel’s requirement.

P6187W-V3 User’s Manual
Supported Input Timing Modes
11
This page is intentionally left blank.

P6187W-V3 User’s Manual
12 OSD Operation
Appendix B
OSD Operation
Function Description of OSD Menu
※The layout and format of OSD depends on customer’s request.
OSD MENU
Description
Picture
Press "+" to increase or "‐" to decrease
The Backlight, Brightness or Contrast.
or Sharpness.
Backlight
Adjust the Backlight of the screen.
Brightness
Adjust the brightness of the signal.
Contrast
Adjust the contrast of the screen.
Sharpness
Adjust the Sharpness of the screen.
Display
Auto Adjustment
Automatic display adjustment
H Position.
Adjust the horizontal position of Screen
V Position.
Adjust the vertical position of the
Screen
Pixel Clock
Adjust Frequency to fill the display
Phase
Adjust the phase control of the image.

P6187W-V3 User’s Manual
OSD Operation 13
Color
Gamma
Set the Gamma to 2.0, 2.2, 2.4 and off.
Color Temp
You can select the screen’s color level of
the white
color field from the default color
temperature
settings.
Also, you can fine tune the color
temperature by
USER option if necessary.
Set color to 6500k , 9300k , USER .
Advance
Aspect Ratio
Select Aspect Ratio
⚫4:3
⚫5:4
⚫16:9
⚫Full

P6187W-V3 User’s Manual
14 OSD Operation
Input
Select the Video input Source
⚫Auto Select
⚫VGA
⚫DP
⚫HDMI
Audio
Volume
Adjust the Volume.
Mute
Set the Mute on/off.

P6187W-V3 User’s Manual
OSD Operation 15
Other
Reset
Menu Time
Adjust the Menu Time.
OSD H. Position.
Adjust the horizontal position of the
OSD Menu screen’s image.
OSD V. Position.
Adjust the vertical position of the
OSD Menu screen’s image.
Language
Set the Language English/繁體中文.
Transparency
Adjust the OSD Transparency.
Rotate
Information
Show as timing and firmware version

P6187W-V3 User’s Manual
16 OSD Operation
This page is intentionally left blank.