AXIOMTEK SDM510L User manual

SDM510L
Intel®Smart Display Module (SDM-L)
with Intel®Core™Alder Lake H/P/U
Processor
User’s Manual
Version:1.0

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
©Copyright 2023 Axiomtek Co., Ltd.
All Rights Reserved
March 2023, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please observe the following precautions:
◼Do not remove modules or integrated circuits from their anti-static packaging until you are
ready to install them.
◼Before holding the module or any integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. Doing so will help discharge static electricity from
your body.
◼When handling modules and components, wear a wrist-grounding strap, available from
most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®, Celeron® are trademarks of Intel Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions ...........................................................................................iii
Section 1 Introduction............................................. 1
1.1 Features ...............................................................................................1
1.2 Specifications......................................................................................2
1.3 Utilities Supported ..............................................................................3
1.4 Block Diagram .....................................................................................4
Section 2 Module and Pin Assignments.................. 5
2.1 Module Dimensions and Fixing Holes...............................................5
2.2 Module Layout.....................................................................................8
2.3 Bracket and Heatsink Installation......................................................9
2.3.1 Bracket Assembly........................................................................................ 9
2.3.2 Heatsink Installation .................................................................................... 9
2.4 Jumper Settings ................................................................................11
2.4.1 Auto Power on (JP1) ..................................................................................11
2.5 Connectors ........................................................................................12
2.5.1 Ethernet Port (LAN1)................................................................................. 12
2.5.2 M.2 M Key 2242 Socket (CN1) ................................................................. 13
2.5.3 M.2 E Key 2230 Socket (CN2) .................................................................. 14
2.5.4 USB 3.2 Gen2 Stack Connectors (CN3，CN4) ........................................ 15
2.5.5 HDMI Connector (CN5,CN6,CN7) ............................................................ 16
2.5.6 Power On/Off button (SW1) ...................................................................... 16
2.5.7 SDM Edge Connector (J1) ........................................................................ 17
Section 3 Hardware Description ........................... 19
3.1 Microprocessor .................................................................................19
3.2 BIOS ...................................................................................................19
3.3 System Memory.................................................................................19
3.4 I/O Port Address Map........................................................................20
3.5 Interrupt Controller (IRQ) Map .........................................................21
3.6 Memory Map ......................................................................................26
Section 4 AMI BIOS Setup Utility.......................... 27
4.1 Starting...............................................................................................27

v
4.2 Navigation Keys ................................................................................27
4.3 Main Menu..........................................................................................29
4.4 Advanced Menu.................................................................................30
4.5 Chipset Menu.....................................................................................41
4.6 Security Menu....................................................................................42
4.7 Boot Menu..........................................................................................45
4.8 Save & Exit Menu ..............................................................................46
Appendix A Watchdog Timer................................... 49
A.1 About Watchdog Timer.....................................................................49
A.2 How to Use Watchdog Timer............................................................49

vi
This page is intentionally left blank.

SDM510L Intel®Smart Display Module (SDM-L)
Introduction 1
Section 1
Introduction
The SDM510L is a new Intel®Smart Display Module (SDM-L) supporting the Intel® Core™
Alder Lake H/P/U processor. It delivers outstanding system performance and supports a
diverse range of multiple I/Os such as one 2.5 GbE Ethernet port, three HDMI 2.0 ports and
four USB. The SDM510L measures only 100 x 175mm and delivers 8K output with streaming
content through the SDM edge connector.
The SDM510L reserves two SO-DIMM slots, two types of M.2 sockets, plus one standard
PCIex8 (through the SDM edge connector). It also features built-in I/O interfaces including
USB 3.2 Gen 2, HDMI 2.1, DisplayPort 1.4, Serial TX/RX and I2C. In addition, for maximum
integration flexibility, the SDM510L can be built-in or externally plugged into a display, which
allows this cost-effective smart display module to fit into even the sleekest all-in-one designs.
1.1 Features
⚫Intel®Core™Alder Lake H/P/U processor
⚫Two SO-DIMM memory slots supporting memory capacity up to 32GB
⚫One M.2 E Key 2230 for Wi-Fi/BT, one M.2 M Key for storage options
⚫Three HDMI ports and one 2.5 GbE LAN port
⚫Easily integrates into slim designs

SDM510L Intel®Smart Display Module (SDM-L)
2Introduction
1.2 Specifications
⚫CPU
◼Intel®Core i3/i5/i7 Celeron® processor.
◼Intel®Core™i5-12600HE processor.
◼Intel®Core™i3-1215UE processor.
◼Intel®Celeron®processor 7305E.
⚫BIOS
◼American Megatrends Inc. BIOS.
◼64Mbit SPI Flash, DMI, Plug and Play.
◼PXE Ethernet Boot ROM; customized default saving features; LPC-free supported;
uses SPI type Flash memory.
⚫System Memory
◼Two SO-DIMM DDR4-3200MHz memory slots, supporting maximum capacity up to
32GB (optional).
⚫Expansion Interface
◼One M.2 E Key 2230 socket for Wi-Fi/Bluetooth option.
◼One M.2 M Key 2242 socket for storage.
⚫USB Interface
◼Three USB 3.2 Gen 2 ports and one USB 2.0 port in Type A on rear I/O.
◼One USB 3.2 Gen 2 port (through SDM edge connector).
⚫Graphics
◼Intel® Iris® XeGraphics (Core™ i7/i5), Intel® UHD Graphics (Core™ i3 and Celeron®).
◼One DP 1.4 (through SDM edge connector), with resolution up to 4096x2160.
◼One HDMI 2.1 (through SDM edge connector), with resolution up to 7680x4320.
◼Three HDMI 2.0b (4096x2160 @60p) (on rear I/O), with voice, no support hot
pluggable.
⚫Ethernet
◼One 2.5 GbE provided by Intel®I225AT support Wake-on-LAN.
⚫WatchDog Timer
◼Timeout value range is 1~255 sec/min.
⚫SDM Edge Connector
◼98-pin golden finger, supporting DP, HDMI, PCI-Express x1, USB 3.2 Gen 2, Serial
TX/RX, I2Cand SPI.
⚫Power Management
◼ACPI (Advanced Configuration and Power Interface).
⚫Form Factor
◼175mm x 60mm.

SDM510L Intel®Smart Display Module (SDM-L)
Introduction 3
1.3 Utilities Supported
⚫Chipset driver
⚫Graphics driver
⚫TXE driver
⚫Serial IO driver
⚫Ethernet utility and driver
Note
All specifications and images are subject to change without notice.

SDM510L Intel®Smart Display Module (SDM-L)
4Introduction
1.4 Block Diagram

SDM510L Intel®Smart Display Module (SDM-L)
Module and Pin Assignments 5
Section 2
Module and Pin Assignments
2.1 Module Dimensions and Fixing Holes
Top View

SDM510L Intel®Smart Display Module (SDM-L)
6Module and Pin Assignments
Bottom View

SDM510L Intel®Smart Display Module (SDM-L)
Module and Pin Assignments 7
Side View

SDM510L Intel®Smart Display Module (SDM-L)
8Module and Pin Assignments
2.2 Module Layout
Top View
Bottom View

SDM510L Intel®Smart Display Module (SDM-L)
Module and Pin Assignments 9
2.3 Bracket and Heatsink Installation
2.3.1 Bracket Assembly
SDM510L i3-1215UE and Celeron 7305E SKU bracket assembly.
2.3.2Heatsink Installation
⚫15W Heatsink Installation
Below chart is for 15W heatsink installation of SDM510L i3-1215UE and Celeron 7305E
“Barebone SKU”. The screw already fixed as circled in image “a” when you received
SDM510L module. Please remove screw as circled in image “b”, then start installation
M.2 SSD. When you finish M.2 SSD installation, please apply retention screws of
heatsink to secure as image “a”. Please noted that the screws (M3*3L) of M.2 module
are in the accessory package.
a
b

SDM510L Intel®Smart Display Module (SDM-L)
10 Module and Pin Assignments
⚫45W Heatsink Installation.
Below chart is for 45W heatsink installation of SDM510L i5-12600HE “Barebone SKU”.
The screw already fixed as circled in image “c” when you received SDM510L module.
Please remove the 4 screws and remove heatsink temporary as image “d”. Then you
can start installation of M.2 SSD/ WIFI module.
Please noted that the screws (M3*3L) of M.2 module are in the accessory package and
finish M.2 SSD and WIFI module installation. Then you can apply retention screws of
heatsink to secure it as the image “e” and stick the mylar on top of heatsink like below “f”
chart.
c
d
e
f

SDM510L Intel®Smart Display Module (SDM-L)
Module and Pin Assignments 11
2.4 Jumper Settings
A jumper is a small component consisting of a set of jumper pins with a jumper clip. Place a
jumper clip on two jumper pins to close; remove a jumper clip from two jumper pins to open.
The following illustration shows how to set up a jumper.
Properly configure jumper settings on the SDM510L to meet your application purpose. Below
you can find a summary table of jumpers and their default onboard settings.
Note
Once the default jumper setting needs to be changed, please do it under power-off
condition.
2.4.1 Auto Power on (JP1)
If JP1 is enabled for power input, the system will be automatically power on without the
need to press the soft power button. If JP1 is disabled for power input, it is necessary to
manually press the soft power button to power on the system.
Function
Setting
Enable auto power on (Default)
1-2 close
Disable auto power on
2-3 close

SDM510L Intel®Smart Display Module (SDM-L)
12 Module and Pin Assignments
2.5 Connectors
Signals go to the other parts of the system through connectors. Loose or improper connection
might cause problems. Please make sure all connectors are properly and firmly connected.
Here is a table summarizing the connectors on the hardware.
Connector
Description
LAN1
2.5G Ethernet Port
CN1
M.2 M Key 2242 Socket
CN2
M.2 E Key 2230 Socket
CN3
USB 3.2 Gen2 Type A Stack Connector
CN4
USB 3.2 Gen2 with USB 2.0 Type A Stack Connector
CN5
HDMI Type A
CN6
HDMI Type A
CN7
HDMI Type A
SW1
Power Button
BAT1
Battery Header
FAN1
Fan Header
J1
SDM Edge Connector
2.5.1 Ethernet Port (LAN1)
The board has one RJ-45 Ethernet connector (LAN1). Connection can be established by
plugging one end of the Ethernet cable into this connector and the other end (phone jack)
to a 2500/1000/100/10-Base-T hub.
2.5G
1000
10/100
Pin
2500 Base-T
L1
MDI0+
L2
MDI0-
L3
MDI1+
L4
MDI1-
L5
MDI2+
L6
MDI2-
L7
MDI3+
L8
MDI3-
B
Active Link LED (Orange )
Off: No link
Blinking: Data activity detected
A
Speed LED
2.5G: Orange
1000: Green
100/10: OFF

SDM510L Intel®Smart Display Module (SDM-L)
Module and Pin Assignments 13
2.5.2 M.2 M Key 2242 Socket (CN1)
This system has one M.2 M Key socket for inserting the M.2 2242 NVMe / SATA SSD
module.
Pin
Signal
Pin
Signal
1
GND
2
+3.3V
3
GND
4
+3.3V
5
PERn9
6
NC
7
PERp9
8
NC
9
GND
10
LED1#
11
PETn9
12
+3.3V
13
PETp9
14
+3.3V
15
GND
16
+3.3V
17
PERn10
18
+3.3 V
19
PERp10
20
NC
21
GND
22
NC
23
PETn10
24
NC
25
PETp10
26
NC
27
GND
28
NC
29
PERn11
30
NC
31
PERp11
32
NC
33
GND
34
NC
35
PETn11
36
NC
37
PETp11
38
DEVSLP
39
GND
40
NC
41
SATA_RXP /PERn12
42
NC
43
SATA_RXN /PERp12
44
NC
45
GND
46
NC
47
SATA_TXN /PETn12
48
NC
49
SATA_TXP /PETp12
50
PERST#
51
GND
52
CLKREQ#
53
REFCLKN
54
PEWAKE#
55
REFCLKP
56
NC
57
GND
58
NC
59
NC
60
NC
61
NC
62
NC
63
NC
64
NC
65
NC
66
NC
67
NC
68
NC
69
PEDET
70
+3.3V
71
GND
72
+3.3V
73
GND
74
+3.3V
75
GND

SDM510L Intel®Smart Display Module (SDM-L)
14 Module and Pin Assignments
2.5.3 M.2 E Key 2230 Socket (CN2)
The module has one M.2 E Key 2230 socket on the top side supporting PCI-Express x1
and USB 2.0
Pin
Signal
Pin
Signal
1
GND
2
+3.3V
3
USB2_DP_6
4
+3.3V
5
USB2_DN_6
6
NC
7
GND
8
NC
9
NC
10
NC
11
NC
12
NC
13
GND
14
NC
15
NC
16
NC
17
NC
18
GND
19
GND
20
NC
21
NC
22
NC
23
NC
24
NC
25
NC
26
NC
27
NC
28
NC
29
NC
30
NC
31
NC
32
NC
33
GND
34
NC
35
PETn5
36
NC
37
PETp5
38
CLINK_RST
39
GND
40
CLINK_DAT
41
PERn5
42
CLINK_CLK
43
PERp5
44
NC
45
GND
46
NC
47
REFCLKN
48
NC
49
REFCLKP
50
SUSCLK
51
GND
52
PLTRST#
53
CLKREQ
54
BT_DISABLE#
55
PEWAKE#
56
WLAN_DISABL
E#
57
GND
58
NC
59
NC
60
NC
61
NC
62
NC
63
GND
64
NC
65
NC
66
NC
67
NC
68
NC
69
GND
70
NC
71
NC
72
+3.3V
73
NC
74
+3.3V
75
GND