AXIOMTEK SHB101 Series User manual

SHB101 Series
Intel® Core™2 Quad/Core™2 Duo
Celeron® Processor PICMG 1.3 Full-
Size
Single Board Computer
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is
recommended by the manufacturer that you follow the manufacturer’s
instructions to only replace the same or equivalent type of battery,
and dispose of used ones.
Copyright 2010 AXIOMTEK Co., Ltd.
All Rights Reserved
January 2010, Version A2
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity.
To prevent chipsets from electrostatic discharge damage, please take
care of the following jobs with precautions:
 Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
 Before holding the board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. It
discharges static electricity from your body.
 Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Windows® is a trademark of Microsoft Corporation.
Phoenix & AWARD are trademarks of Phoenix Technology Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel® CoreTM 2 Quad/ CoreTM 2 Duo/Celeron® are trademarks of
Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered
brands of their respective owners.

iv
Table of Contents
Disclaimers ............................................................................................................... ii
ESD Precautions ..................................................................................................... iii
CHAPTER 1 INTRODUCTION......................................................................................... 1
1.1 Specifications.............................................................................................. 2
1.2 Utilities Supported....................................................................................... 3
1.3 I/O Bracket.................................................................................................. 4
CHAPTER 2 JUMPERS AND CONNECTORS ............................................................... 5
2.1 Board Dimensions....................................................................................... 5
2.2 Board Layout ............................................................................................... 6
2.3 Jumper Settings .......................................................................................... 7
2.3.1 COM2 Mode Select Jumpers for RS-232/422/485 (JP1, JP2, JP3).... 7
2.3.2 CMOS Clear Jumper (JP6) ................................................................. 8
2.3.3 ATX Auto Power On/Off (JP7) ............................................................ 8
2.4 Connectors.................................................................................................. 9
2.4.1 ATX 4 Pin 12V In Connector (CN2)................................................... 10
2.4.2 Front Panel Connector (CN3) ............................................................ 10
2.4.3 LAN1, LAN2 Link/Active LED Connectors (CN4, CN7)..................... 11
2.4.4 LAN1, LAN2 Speed LED Connectors (CN5, CN6)............................ 11
2.4.5 COM Port RS-232 Pin Assignment (COM1, COM2)......................... 12
2.4.6 COM2 RS-422/485 Pin Assignment.................................................. 12
2.4.7 CPU Fan Connector (FAN1).............................................................. 13
2.4.8 System Fan Connectors (FAN2, FAN3) ............................................ 13
2.4.9 Floppy Disk Port Connector (FDD1) .................................................. 13
2.4.10 Intel® HD Audio Digital Header (HDA1) ............................................. 14
2.4.11 PS/2 Keyboard, Mouse Connector (KB1, MS1)................................. 15
2.4.12 Ethernet RJ-45 Connectors (LAN1/LAN2) ........................................ 15
2.4.13 Parallel Port Connector (PRN1)......................................................... 16
2.4.14 SATA Connectors (SATA1~6) .......................................................... 17
2.4.15 USB Connectors (USB1/USB2) ........................................................ 17
2.4.16 USB Port Connector (USB3/USB4)................................................... 18
2.4.17 DB15 CRT Connector (VGA1) .......................................................... 18
CHAPTER 3 HARDWARE INSTALLATION ................................................................. 19
3.1 Installing the Processor............................................................................. 19
3.2 Installing the Memory ................................................................................ 24
CHAPTER 4 HARDWARE DESCRIPTION ................................................................... 25
4.1 Microprocessors........................................................................................ 25
4.2 BIOS ......................................................................................................... 25
4.3 System Memory ........................................................................................ 25
4.4 I/O Port Address Map ............................................................................... 26
4.5 Interrupt Controller (IRQ) Map .................................................................. 27
CHAPTER 5 PHOENIX-AWARD BIOS UTILITY .......................................................... 29
5.1 Entering Setup .......................................................................................... 29
5.2 Control Keys.............................................................................................. 30

v
5.3 Getting Help .............................................................................................. 30
5.4 The Main Menu ......................................................................................... 31
5.5 Standard CMOS Setup Menu ................................................................... 32
5.6 Advanced BIOS Features ......................................................................... 35
5.7 Advanced Chipset Features...................................................................... 40
5.8 Integrated Peripherals ............................................................................... 42
5.9 Power Management Setup ........................................................................ 46
5.10 PnP/PCI Configuration Setup ................................................................... 50
5.11 PC Health Status ...................................................................................... 52
5.12 Frequency/Voltage Control........................................................................ 53
5.13 Load Fail-Safe Defaults............................................................................. 54
5.14 Load Optimized Defaults........................................................................... 55
5.15 Set Supervisor/User Password ................................................................. 56
5.16 Save & Exit Setup ..................................................................................... 57
5.17 Exit Without Saving................................................................................... 58
CHPATER 6 INSTALLATION OF DRIVERS................................................................. 60
6.1 Installing Chipset Driver ............................................................................ 60
6.2 Installing VGA Driver................................................................................. 63
6.3 Installing LAN Driver ................................................................................. 66
APPENDIX A WATCHDOG TIMER............................................................................... 70
APPENDIX B PCI IRQ ROUTING.................................................................................. 72
APPENDIX C CONFIGURING SATA FOR RAID FUNCTION ...................................... 74
APPENDIX D PICMG v1.3 INTERFACE DEFINITION.................................................. 86

vi
MEMO

SHB101 LGA775 Full-Size SBC User’s Manual
Introduction 1
CHAPTER 1
INTRODUCTION
The SHB101 PICMG 1.3 full-size Single Board Computer supports
LGA775 socket for Intel® Core™ 2 Quad / Core™ 2 Duo/Celeron®
processors with 45/65nm technology and FSB 800/1066/1333 MHz.
The board integrates Intel® Q35 and ICH9R chipset that delivers
outstanding system performance through high-bandwidth interfaces,
multiple I/O functions for interactive applications and various
embedded computing solutions. There are four 240-pin DDR2 DIMM
sockets for dual channel DDR2 667/800, maximum memory capacity
up to 8GB. The board also features dual Gigabit Ethernet, six serial
ATA ports at maximum transfer rate up to 3Gbs, and SATA RAID
0/1/5/10 by ICH9R. Ten USB 2.0 high speed compliant ports and
built-in Intel® HD Audio Digital Header (optional) can achieve the
best stability and reliability for industrial applications.

SHB101 LGA775 Full-Size SBC User’s Manual
Introduction
2
1.1 Specifications
 CPU
 Intel® Core™ 2 Quad / Core™ 2 Duo/Celeron®
processors
 System Chipset
 Intel® Q35 and ICH9R
 CPU Socket
 LGA775 Socket
 Front-Side Bus
 800/1066/1333 MHz
 BIOS
 Phoenix-Award BIOS via SPI interface with socket
 System Memory
 Four 240-pin DDR2 DIMM sockets
 Maximum up to 8GB DDR2 memory
 Support DDR2 667/800 memory
 L2 Cache: integrated in CPU
 Onboard Multi-I/O
 Parallel Port: one 26-pin 2.54 pitch box-header,
SPP/EPP/ECP supported
 Serial Port: one for RS-232 (COM1) and one port for
RS-232/422/485 (COM2)
 Floppy controller: supports two drives (1.44MB for each)
 USB Interface
 Ten USB ports compliant with USB Spec. Rev. 2.0 (Six
ports on SHB101, four ports to SHB connector-C golden
fingers)
 VGA Controller
 Chipset -- Intel® integrated Graphics Gen3.5 on Intel® Q35
supports 3D, 2D, video capabilities
 Memory Size -- Intel® DVMT 128/256MB supported;

SHB101 LGA775 Full-Size SBC User’s Manual
Introduction 3
preallocated memory for frame buffer option as 8MB
 Resolution -- Analog output -- the analog port utilizes an
integrated 350MHz 24-bit RAMDAC that can directly drive a
standard progressive scan analog monitor up to a resolution
of 2048x1536 pixels with 32-bit color at 75 Hz
 Analog Output Interface -- CRT from DAC output via 15-pin
D-Sub connector on the edge; CRT always ON supported
 Ethernet
 The LAN1/LAN2 is 82573L Ethernet controller support
10/100/1000 Mb/s
 Dual PCI-Express x1 LAN
 Serial ATA
 Support Serial ATA/Serial ATA II
 Six Serial ATA-II ports, 3GB/s performance and SATA RAID
0/1/5/10 by ICH9R
 Audio
 16-pin 2.54 pin-header (Intel® HD Audio Digital Header)
(optional)
 Hardware Monitoring
 Monitoring temperatures, voltages, and cooling fan status
 Watchdog Timer
 Reset Supported (1-255 level)
 Dimensions
 338mm x 126mm
NOTE All specifications and images are subject to change without
notice.
1.2 Utilities Supported
 Intel® Q35 Utility and Drivers
 VGA Drivers
 Ethernet Utility and Drivers
 RAID Utility

SHB101 LGA775 Full-Size SBC User’s Manual
Introduction
4
1.3 I/O Bracket

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors 5
CHAPTER 2
JUMPERS AND CONNECTORS
2.1 Board Dimensions

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
6
2.2 Board Layout

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors 7
2.3 Jumper Settings
Proper jumer settings configure the SHB101 to meet your application
purpose.
2.3.1 COM2 Mode Select Jumpers for RS-232/422/485
(JP1, JP2, JP3)
These jumpers select the COM2 port’s communication mode to
operate RS-232 or RS-422/485.
Description
Function
Jumper Setting
RS-232
(Default)
JP1
JP2 JP3
RS-422 JP1
JP2 JP3
COM2
RS-485 JP1
JP2 JP3

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
8
2.3.2 CMOS Clear Jumper (JP6)
You may need to use this jumper is to clear the CMOS memory if
incorrect BIOS settings.
Description
Function
Jumper Setting
Normal
(Default)
JP6
CMOS
Clear
Clear
CMOS
JP6
2.3.3 ATX Auto Power On/Off (JP7)
When Jumper JP7 is set OPEN for AC power input, the system will be
automatically power ON without pressing soft power button; when JP7
is SHORT for AC power input, it is necessary to manually press soft
power button to make the system power ON.
Note This function is similar to the feature of Power On after
Power Failed, which is controlled by hardware circuitry
instead of BIOS.
Description
Function
Jumper Setting
Disable
(Default)
JP7
ATX Auto
Power
On/Off
Enable JP7

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors 9
2.4 Connectors
Connectors connect this board with other parts of the system. Loose or
improper connection might cause problems. Make sure all connectors
are properly and firmly connected.
Here is a summary table shows you all connectors on the board.
Connector Label Connector Label
ATX 4 Pin 12V In CN2 Floppy Connector FDD1
Front Panel Connector CN3 Parallel Port PRN1
LAN2 Link / Active LED CN4 Serial ATA Connectors
SATA1~6
LAN2 Speed LED CN5 USB Connector USB1~4
LAN1 Speed LED CN6 DB15 CRT Connector VGA1
LAN1 Link / Active LED CN7 DDRII DIMM Sockets DDR1~4
Serial Port1 Connector COM1 PS/2 Mouse Connector
MS1
Serial Port2 Connector COM2 PS/2 Keyboard
Connector KB1
CPU FAN Connector FAN1 Intel HD Audio Digital
Header HDA1
System FAN Connector FAN2 LAN1 Connector LAN1
System FAN Connector FAN3 LAN2 Connector LAN2

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
10
2.4.1 ATX 4 Pin 12V In Connector (CN2)
You can connect it to the ATX12V power supply for CPU Core Voltage.
Pin
Signal
1 GND
2 GND
3 +12V
4 +12V
CN2
2.4.2 Front Panel Connector (CN3)
 Power LED
This 3-pin connector denoted as Pin 1 and Pin 5 connects the
system power LED indicator to such a switch on the case. Pin 1 is
assigned as +, and Pin 5 as -. The Power LED lights up when the
system is powered ON. Pin 3 is defined as GND.
 External Speaker and Internal Buzzer Connector
Pin 2, 4, 6 and 8 can be connected to the case-mounted speaker
unit or internal buzzer. While connecting the CPU card to an
internal buzzer, please short pins 2-4; while connecting to an
external speaker, you need to set pins 2-4 to Open and connect the
speaker cable to pin 8 (+) and pin 2 (-).
 ATX Power On/Off Button
This 2-pin connector denoted as Pin 9 and 10 connects the front
panel’s ATX power button to the CPU card, which allows users to

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors 11
control ATX power supply to be power on/off.
 System Reset Switch
Pin 11 and 12 can be connected to the case-mounted reset switch
that reboots your computer instead of turning OFF the power switch.
It is a better way to reboot your system for a longer life of the
system’s power supply.
 HDD Activity LED
This connection is linked to hard drive activity LED on the control
panel. LED flashes when HDD is being accessed. Pin 13 and 14
connect the hard disk drive to the front panel HDD LED, Pin 13
assigned as -, and Pin 14 as +.
2.4.3 LAN1, LAN2 Link/Active LED Connectors (CN4,
CN7)
Pin Signal
1 LED (+)
2 LED (-)
CN4, CN7
2.4.4 LAN1, LAN2 Speed LED Connectors (CN5, CN6)
Pin Signal
1 100, Low Active
2 + 3.3V
3 1000, Low Active
CN5, CN6

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
12
2.4.5 COM Port RS-232 Pin Assignment (COM1, COM2)
The serial interface for the board consists of COM1 port (COM1)
support for RS-232, and COM2 (COM2) for RS-232/RS422/RS485.
Pin
Signal Pin
Signal
1
Data Carrier Detect
(DCD) 2
Data Set Ready (DSR)
3
Receive Data (RXD)
4
Request to Send (RTS)
5
Transmit Data (TXD)
6
Clear to Send (CTS)
7
Data Terminal Ready
(DTR) 8
Ring Indicator (RI)
9
Ground (GND) 10
Ground (GND)
COM1, COM2
2
4
6
1
3
5
78
910
2.4.6 COM2 RS-422/485 Pin Assignment
COM2 Serial Port 10-pin (Box-header) Connector Pin Assignment list
Signal Name
Pin # RS-422 RS-485
1 TX- DATA-
2 No connector No connector
3 TX+ DATA+
4 No connector No connector
5 RX+ No connector
6 No connector No connector
7 RX- No connector
8 No connector No connector
9 GND GND
10 GND GND

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors 13
2.4.7 CPU Fan Connector (FAN1)
A CPU fan is always needed for cooling CPU heat. The CPU fan
connector FAN1 provides power to the CPU fan.
Pin
Signal
1
Ground
2
+12V
3
Rotation Detection
4
Speed Control
FAN1
2.4.8 System Fan Connectors (FAN2, FAN3)
You can connect the system cooling fan cable to FAN2/FAN3 for
system cooling fan power.
Pin Signal
1 GND
2 +12V
3 Rotation Detection
FAN2, FAN3
2.4.9 Floppy Disk Port Connector (FDD1)
The board provides a 34-pin header type connector, FDD1, supporting
up to two floppy drives. The floppy drives may be any one of the
following types: 5.25" 360KB/1.2MB and 3.5" 720KB/1.44MB/2.88MB.
Pin
Signal Pin
Signal Pin
Signal
1
GND 2
Drive Density Select 3
GND
4
No connector 5
GND 6
No connector
7
GND 8
Index# 9
GND
10
Motor enable A# 11
GND 12
No connector
13
GND 14
Drive select A# 15
GND
16
No connector 17
GND 18
Direction#
19
GND 20
STEP# 21
GND
22
Write data# 23
GND 24
Write gate#
25
GND 26
Track 0 # 27
GND

SHB101 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
14
Pin
Signal Pin
Signal Pin
Signal
28
Write protect# 29
No connector 30
Read data#
31
GND 32
Head selection# 33
No connector
34
Disk change#
FDD1
2.4.10 Intel® HD Audio Digital Header (HDA1)
Pin
Signal Pin
Signal
1
BCLK 2
GND
3
RST# 4
VCC3
5
SYNC 6
GND
7
SDOUT 8
VCC3
9
SDI0 10
+12V
11
No connector
13
No connector 14
3VDUAL
15
No connector 16
GND
HDA1