Axminster UV-180DS User manual

UV-180DS 7"
Bandsaw
Code 103629
AT&M: 27/01/2017

TABLE OF CONTENTS
Warning...............................................................................................................................................................1
Prior to Operation ...............................................................................................................................................2
Before Cutting.....................................................................................................................................................2
Assembly Material Stopper.................................................................................................................................2
The Base ............................................................................................................................................................2
Coolant System ..................................................................................................................................................2
Operation of Control Box ....................................................................................................................................3
Hydraulic Feed Selector Operation ....................................................................................................................3
Spring Setting .....................................................................................................................................................3
Adjusting movable Blade Guide .........................................................................................................................3
Vise Operation ....................................................................................................................................................4
Adjusting Blade Tension .....................................................................................................................................4
Changing Blades ................................................................................................................................................4
Adjusting Blade Square to Table ........................................................................................................................5
Adjusting Blade Square to Vise ..........................................................................................................................5
Adjusting Blade Tracking....................................................................................................................................5
Adjusting Blade Guide Bearings.........................................................................................................................6
Adjusting Bow Angle...........................................................................................................................................6
Maintenance .......................................................................................................................................................7
Selecting the Blade.............................................................................................................................................7
Blade Speeds .....................................................................................................................................................7
Circuit Diagram ...................................................................................................................................................8

1
Warning
1. Read and understand the entire instruction manual before operating machine.
2. Always wear approved safety glasses/face shields while using this machine.
3. Make certain the machine is properly grounded.
4. Before operating the machine, remove tie, rings, watches, other jewelry, and roll up sleeves above the
elbows. Remove all loose clothing and confine long hair. Do not wear gloves.
5. Keep the floor around the machine clean and free of scrap material, oil and grease.
6. Keep machine guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
7. Do not overreach. Maintain a balanced stance at all times so that you do not fall or lean against blades
or other moving parts.
8. Make all machine adjustments or maintenance with the machine unplugged from the power source.
9. Use the right tool. Don’t force a tool or attachment to do a job which it was not designed for.
10. Replace warning labels if they become obscured or removed.
11. Make certain the motor switch is in the off position before connecting the machine to the power supply.
12. Give you work undivided attention. Looking around, carrying on a conversation, and “horse-play” are
careless acts that can result in serious injury.
13. Keep visitors a safe distance from the work area.
14. Use recommended accessories; improper accessories may be hazardous.
15. Make a habit of checking to see that keys and adjusting wrenches are removed before turning on the
machine.
16. Always keep hands and fingers away from the blade when the machine is running.
17. Never hold the material with the saw in the horizontal position. Always use the vise and clamp it
securely.
18. Read and understand warning posted on the machine.
19. Keep the belt guard and wheel covers in place and in working order.
20. Always provide adequate support for long and heavy material.
21. Use a sharp blade and keep machine clean for best and safest performance.
22. Failure to comply with all of these warnings may cause serious injury.
23. This machine is only used for horizontal metal cutting, not vertical woodwork cutting.

2
Prior to Operation
1. Check to see blade tooth direction matches
diagram on saw body.
2. Check to see that blade is properly seated on
wheels after proper tension has been applied.
3. Set blade guide roller bearing snug against
blade. See Adjusting Blade Guide Bearings for
more details.
4. Check for slight clearance between vertical
rollers and back of blade.
5. Position movable blade guide as close to work
as possible.
6. Select proper speed and feed rate for materials
being cut.
7. Material to be cut must be held securely in vise.
8. Do not start cut on a sharp edge. File the edge
first.
Before Cutting
1. Finish uncrating the saw. Inspect it for
shipping damage. If any damage has occurred,
contact you are distributor.
2. Unbolt the saw from the skid and place it on a
level surface.
3. Clean rust protected surfaces with kerosene,
diesel oil, or a mild solvent. Do not use
cellulose based solvents such as paint thinner
or lacquer thinner. These will damage painted
surfaces.
4. Assembly coolant collectors (R) at the left and
right side of the base.
Fig. 1
Assembly Material Stopper
1. Screw in the length bar (A, Fig. 2) into base
until position it. Slide material stop (B) onto bar
and tighten lock screw(C) at proper position.
2. Remove transportation strap and keep for later
use should the saw be moved any distance.
Fig. 2
The Base
The base is a structure supporting the saw frame,
the vise, the bar stop, the work piece supporter,
coolant pump, swing arm, and the coolant return
plates. The base house includes the cooling liquid
tank.
Fig. 3
Coolant System
Oils for Lubricating Coolant
Considering the vast range of products on the
market, the user can choose the one most suited to
their own requirements, using as reference the type
SHELL LUTEM OIL ECO. THE MINIMUM
PERCENTAGE OF OIL DILUTED IN WATER IS 10
- 20 %.
Cleaning the Tank
Use hex wrench to open the plug located on the
rear base below the pump. Allow the coolant to
drain-out.
Remove the filter net (P) by loosening the four
screws.
Remove the pump (Q) by loosening the four screws.
Use a vacuum cleaner to vacuum chips and debris
from the tank.
Replace the plug.
Thoroughly clean the pump (Q) and replace.
Fill the tank with coolant to approximately 25mm
below the filter net (P).
Clean and replace the filter net.
B
A
C
R

3
Fig. 4
Operation of Control Box
Fig. 5
1. Emergency stop switch
Press down the Emergency switch to stop all of
machine function if any unsafely situation
occurred.
2. Stop power button
O: Press to disconnect the power of motor.
3. Power on button
I: Press to connect the power of motor
4. Blade speed adjusting knob
Variable blade speed is controlled by the knob.
Turn knob clockwise to increase speed from 25
to 85mpm. Turn knob counter clockwise to
decrease blade speed.
5. Cutting mode selection Switch
There is two cutting modes and neutral position
can be selected. Select any cutting mode the
power should be cut by the neutral position.
a. manual mode
b. Hydraulic flow controlled descend mode.
Turn switch left for hydraulic controlled
descend mode and right for manual mode.
6. Coolant ON/OFF Switch
I: Turn on the coolant
O: Turn off the coolant
Hydraulic Feed Selector Operation
The hydraulic feed selector is used to control
cutting feed down rate and lock the bow in the
proper position.
To turn off the flow of hydraulic fluid, pull lever (B)
to vertical with the cylinder.
To turn the hydraulic fluid on, pull lever (B) to
parallel with the cylinder.
Open hydraulic on (B), turn knob (A, Fig. 7)
counter-clockwise to increase the feed rate ;
decrease the feed rate, turn knob (A) clockwise.
Fig. 7
Spring Setting
According to operation mode-manual or hydraulic
controlled descend mode, the spring need to be
readjusted as following instruction:
- Hydraulic control descend mode: Turn nut (A,
Fig.8) counter clockwise to the end to loose spring
tension, open hydraulic valve and adjust hydraulic
flow control knob to control saw frame down
speed.
- Manual mode: Open hydraulic valve and turn
hydraulic control knob counter clockwise to the
end to fully open the control flow, the saw frame
will down to the lowest location, turn handle nut (A,
Fig.8) clockwise to tension spring until bow can
rise up higher than vise jaw or material.
Fig. 8
Adjusting movable Blade Guide
1. Disconnect machine from the power source.
2. Loosen lock handle A and knob B (Fig.9).
Slide blade guide assemblies as close as
possible to the material for cutting stably.
3. Tighten handle A and knob B after adjusting.
P
Q
A
B
A
1
2
3
4 5 6

4
CAUTION!
NEVER OPERATE SAW WITHOUT BLADE
GUARDS IN PLACE.
Fig. 9
Vise Operation
WARNING
Do not make any adjustments or load/unload
material from vise while machine is running!
Failure to comply may cause serious injury!
The vise is mounted on the machine base. Follow
the easy steps to open or close the vise.
1. Turn the handle (A) Fig.10 counter clockwise to
open the vise jaw to allow the width of vise can
load work piece.
2. Make sure the work piece is well located on the
table. Turn the handle (A) clockwise to close
the vise jaw to clamp the work piece.
Fig. 10
Adjusting Blade Tension
WARNING
Disconnect machine from the power source!
Blades are sharp! Use extra care when
removing, installing or adjusting!
Failure to comply may cause serious injury!
Blade tension is important to the proper operation of
the saw. This saw proper blade tension is in 1100
to 1500kg/cm2as measured on blade tension
gauge.
To set the blade tension without the use of a
blade tension gauge:
1. Disconnect machine power, open wheel covers
to install blade belt between wheels and insert
blade between bearings on blade guides.
2. Tension blade slightly to remove any sag in
blade between blade wheels.
3. Turn blade tension knob (A, Fig. 11) clockwise
to tighten until the red line approach to central
line (B, Fig. 11).
4. After blade has been completely installed,
close wheel covers, connect to the power
source, and run saw for one minute so blade
can seat properly.
CAUTION !
Do not over tighten blade. This may cause
blade to stretch and warp.
Fig. 11
Changing Blades
WARNING
Never operate this saw unless all blade guards
are installed and in proper working order!
Never adjust blade brush while machine is
running.
Failure to comply may cause serious injury!
CAUTION!
This machine is designed and intended for use
with blades that are 19mm width, 0.9mm
thickness and 2285mm length. Use of blades
with different specification may cause inferior
performance.
1. Disconnect machine from the power source.
2. Raise saw bow to proper position and lock in
place by turning hydraulic valve switch off.
3. Remove saw bow cover (A, Fig. 12) by
removing six screws (B).
4. Loose blade guard nuts and screws (C, Fig.
13). Remove right and left two blade guards.
5. Loosen blade tension by turning blade tension
knob (D) counter-clockwise.
A
A
B
A
B

5
6. Carefully remove old blade. Caution: blade
teeth are sharp. Handle with care.
7. Install new blade (E) by placing blade between
blade guides (F) first. Make sure blade teeth
face the same direction as indicated on the
label found on the saw bow.
8. Place blade around both wheels. Make sure
the blade back edge rests near the wheel
flange on both wheels.
9. Turn blade tension knob clockwise to tension
blade to tighten until the red line approach to
central line (B, Fig. 11). Do not over tension.
10. Put on the blade guards and tighten blade
guard nuts and screws
11. Close blade wheel cover and secure with lock
screws.
12. Connect machine to the power source.
13. Run saw and make sure blade is tracking
properly.
WARNING
It is essential the guards be installed after the new
blade has been fitted.
Failure to comply may cause serious injury!
Fig.12
Fig.13
Adjusting Blade Square to Table
1. Disconnect machine from the power source.
2. Place machinist’s square on the table next to
the blade as in Figure 14.
3. Check to see blade makes contact with the
square along the entire width of the blade.
4. If adjustment is necessary, loosen bolt (A, Fig.
14) and rotate blade guide assemblies slightly
in the same direction until blade makes contact
with the square along its entire width.
5. Tighten bolts (A, Fig. 14).
6. Connect machine to the power source.
Note: If adjustment to square blade to table is
necessary, be sure to check blade adjustments
again.
Fig. 14
Adjusting Blade Square to Vise
1. Disconnect machine from the power source.
2. Place a machinist’s square as pictured in Fig.
15 square should lie along entire length of vise
and blade without a gap.
3. If adjustment is necessary, loosen saw frame
lock bolts and swiveling saw frame to match
with vise square so that square lines up
properly. Tighten lock bolts.
4. Connect machine to the power source.
Fig. 15
Adjusting Blade Tracking
WARNING
Blade tracking adjustment requires running the saw
with the back cover open. This adjustment must be
completed by qualified persons only!
Failure to comply may cause serious injury!
Note: Before making any tracking adjustments, try
a new blade. Warped blades do not track well.
Blade tracking has been set at the factory and
should not require adjustment. If a tracking
problem occurs, adjust the machine as follows:
B
A
D
C
F
E
C
A
F

6
1. Move saw bow to proper height position and
lock in place by shutting off the hydraulic
cylinder valve.
2. Confirm that blade tension is set properly. To
adjust, see section titled Adjusting Blade
Tension.
3. Open back wheel cover by loosening lock
screws.
4. Run saw and observe blade. Blade should run
next to but not tightly against wheel flange.
5. If need to adjust blade track, remove the
screws of cover (A, Fig.16).
6. Loosen bolts (B) a little bit.
7. Turn setscrew (C) while observing blade
tracking on wheel. Turn setscrew (C)
clockwise to track blade closer to the wheel
flange. Turn set screw counter-clockwise to
track blade away from the wheel flange.
8. Once tracking is set, tighten bolts (B).
9. Recovery the cover (A).
Fig. 16
Adjusting Blade Guide Bearings
CAUTION !
This machine is designed and intended for use
with blades that are 19mm width, 0.9mm
thickness and 2285mm length. Use of blades
with different specification may cause inferior
performance.
1. Disconnect machine from the power source.
2. Raise arm up to proper position and lock in
place by turning off the hydraulic cylinder valve.
3. Loosen hex cap screw (A, Fig. 17) and adjust
assembly so that back roller bearing is
approximately 0.08mm-0.12mm from the back
of the blade.
4. Turn nut (B) to adjust eccentric bearing shaft to
the blade (the other side bearing shaft is fixed).
Blade should still move up and down freely
when grasped. Warning! Make sure power is
disconnected and hands are protected before
handling blade. Be sure that blade teeth do not
interfere with the roller bearings.
5. Connect machine to the power source.
Fig. 17
Adjusting Bow Angle
For miter cutting, it needs to swivel saw frame to
desired angle. The cutting angle for this machine is
0 ~ 60° on the left side, 0~45° on the right side.
There is a bar (A Fig18) for frame to stop at zero
position on right side swiveling moving, if need to
cut in the left side that have to pull out the zero
position lock bar (A) then swivel frame to set
desired angle at the left cutting. Loosen the frame
tighten lock handle (B, Fig.18) and wing nut (D, Fig.
19) at the other side before swiveling.
Swiveling saw frame and seat to desired angle
which indicated with angle scale (C). Then Tighten
handle screw and wing nut eventually.
Fig. 18
Fig.19
A
C
B
A
D
B
A
B
C

7
Maintenance
WARNING
Disconnect machine from the power source
before making any repair or adjustment!
Failure to comply may cause serious injury!
1. Keep all surfaces clean and free of rust, slag,
chips.
2. Do not use compressed air to clean band saw.
Compressed air may force chips into the guide
bearings and other critical areas of the saw.
3. Use a small paint brush or parts cleaning
brush to remove metal particles.
4. Wipe saw with a clean dry cloth and oil all
unpainted surfaces with light machine oil.
5. Keep blade guides clean and free of metal
chips.
6. Check guide bearings frequently to make sure
they are properly adjusted and turning freely.
Selecting the Blade
This machine uses 19 x 0.9 x 2285mm blade.
Refer to the section on selecting the blade.
Blade Selection Chart
1. A general- use high speed steel blade in
furnished with this metal cutting band saw.
2. Never use a blade so coarse that less than 3
teeth are engaged in the work piece at any time.
(Too few teeth will cause teeth to strip out.)
3. Never use a blade finer then required obtaining
a satisfactory surface finish or satisfactory
flatness. (Too many teeth engaged in the work
piece will prevent attainment of a satisfactory
sawing rate; frequently cause premature blade
wearing; frequently produce "dished" cuts or the
cuts are neither square nor parallel.)
4. The chart is not expected to be correct for all
cases. It is intended as a general guide to good
sawing practices. Your blade supplier or
qualified engineers should be you most reliable
source for correct information on operational
details of saw blades and their use.
Note:
a. When cutting a thin walled pipe, angle steel,
and I-beam steel use a blade with 5/8 T/in.
b. Cutting pipe with 1/2" or more wall thickness
uses a blade with 5/8T/in or 4/6T/in.
c. When cutting angle steel, H-beam, or solid bar
material, cut the thinnest cross section of the
material first. There must be at least 3 teeth
cutting the material at all times.
Blade Speeds
When user operates band saw always change
the blade speed to best suit the material being
cut.
Adjust the blade speed while the machine is
running. Controls the variable speeds between 35-
85MPM, turn the speed control knob to get desired
speed for cutting the work piece, below is blade
speed chart for cutting reference.
Blade speed selection chart
1. 35~39mpm
Tool steel,
stainless steel,
Hard cast iron,
Alloy steel, Hard
bronze
2. 40 ~ 59mpm
Mild steel, Soft
cast iron,
Medium hard
bronze, Hard
aluminum.
3. 60 ~ 85mpm
Plastics,
Soft and
medium
aluminum,
Other light
materials.

8
Circuit Diagram

SECTION A - PARTS LIST
Part No. Stock No. Description Size Q'ty
A1 UV180A105 Base 1
A2 Socket Head Cap Screw M10x30 4
A3 Angle Plate 2
A4 Cross Round Head Screw M5x10 2
A5 UV180A309 Swivel Plate 1
A6 Scale 1
A7 UV180A106 Vise Base 1
A8 Socket Head Cap Screw M8x65 4
A9 UV180A201 Swiveling Shaft 1
A10 UV180A314 Vise Plate 2
A11 Cross Flat Head Screw M6x16 4
A12 UV180222 Shaft 1
A13 Pin 6x20 2
A14 UV180113 Length Stop 1
A15 Wing Screw 5/16x3/4 1
A16 Nut M8 1
A17 Hex Cap Screw M8x45 1
A18 UV180A107 Dovetail Gib 1
A19 Flat Washer M8 2
A20 Socket Head Cap Screw M8x16 2
A21 Socket Head Cap Screw M8x20 2
A22 UV180A104 Vise Base 1
A23 Socket Head Cap Screw M8x20 2
A24 Flat Washer 2
A25 UV180A311 Plate 1
A26 Socket Head Cap Screw M8x12 1
A27 Flat Washer 8x23x2 1
A28 Set Screw M6x10 2
A29 UV180A103 Vise 1
A30 Set Screw M6x5 5
A31 UV180A204 Adjustment Bushing 2
A32 UV180A202 Spacer 1
A33 UV180A203 Lead Screw 1
A34 UV180211B Handle 1
A35 Handle End M6 2
A36 UV180A211 Bracket 1
A37 C-Ring S-15 2
A38 Pan Head Screw M8x30 2
A39 UV180A207 Position Rod 1
A40 UV180A401 Spring D8xd6x14L 1
A41 UV180A208 Position Rod 1
A42 UV180A209 Vise Eccentric Shaft 1
A43 UV180A210 Shaft 1
A44 Grip 5/16" 1
A45 UV180A102 Miter Plate 1
A46 UV180A403 Lock Handle M8 (TRT-80) 1
A47 Lock Washer M6 2
A48 Socket Head Cap Screw M6x25 2
A49 UV180107A Cylinder Lower Fixed Bracket 1
A50 UV180218 Shaft 1
A51 Set Screw M4x8 1
A52 Hex Cap Screw M8x20 1
A53 Hex Nut M8x12x4.5 1
A54 Wing Hex Nut M8 1
9

SECTION A - PARTS LIST
Part No. Stock No. Description Size Q'ty
A55 UV180A315 Pointer 1
A56 Cross Round Head Screw M5x10 1
A57 UV180308A Spring Lower Bracket 1
A58 UV180405A Spring 1
A59 Spring Washer M5 4
A60 Socket Head Cap Screw M5x16 4
A61 UV180308 Spring Upper Bracket 1
A62 Flat Washer 12x21x2 1
A63 Spring Washer M12 1
A64 Hex Cap Screw M12x30 1
A65 Wing Hex Nut M16 1
A66 Hex Cap Screw M16x140 1
A67 UV180A206 Main Shaft 1
A68 Bearing 30304 2
A69 UV180A205 Special Washer 1
A70 Nylon Nut M20x1.5 1
A71 Hex Nut M10 1
A72 Hex Cap Screw M8x60 1
A73 UV180104 Rear Guide Bearing Bracket 1
A74 7120209 Pin 1
A75 Flat Washer 8x18x2 1
A76 Hex Cap Screw M8x30 1
A77 Hex Nut 3/8x24 4
A78 Spring Washer 3/8 4
A79 UV180314 Rear Blade Guard 1
A80 Cross Flat Head Screw 1/4x20 2
A81 7120136 Blade Guide Block 2
A82 Flat Washer 1/4”x13x1 2
A83 Spring Washer 1/4” 2
A84 Socket Head Cap Screw 1/4”x3/4” 2
A85 7120211-1 Center Shaft 2
A86 7120421 Bearing 608 10
A87 E-Ring 3CM1-8 4
A88 7120211 Eccentric Shaft 2
A89 Set Screw M8x16 1
A90 UV180404A Blade Guide Block R 1
A91 UV180404 Blade Guide Block L 1
A92 UV180103A Guide Bearing Side Bracket 1
A93 Machine Screw M4x16 2
A94 Socket Head Cap Screw M5x25 1
A95 Socket Head Cap Screw M5x50 1
A96 UV180210 Bearing Bush 1
A97 Flat Washer 5/16x16x1 1
A98 Knob M8x16 1
A99 Flat Washer 8x18x2 1
A100 Socket Head Cap Screw M6x12 1
A101 9160417 Copper Fitting 1/4Px1/8 1
A102 Socket Head Cap Screw M8x45 1
A103 Flat Washer 8x21x2 1
A104 UV180411 Lock Handle M8 1
A105 UV180103 Front Guide Bearing Bracket 1
A106 UV180426 Front Blade Guard 1
A107 Hex Nut M5 1
10

11

SECTION B - PARTS LIST
Part No. Stock No. Description Size Q'ty
B1 UV180101 Bow 1
B2 L25A5-35 Cable Tie 4
B3 Cross Round Head Screw M5x10 7
B4 Motor Relay 1
B5 Socket Head Cap Screw M5x35 4
B6 UV180401 Plastic Cover 1
B7 UV180219 Axle 1
B8 UV180408 Hydraulic Cylinder 1
B9 Hex Nut M8 1
B10 UV180A101 Upper Bracket 1
B11 Flat Washer 8x18x2 1
B12 Socket Head Cap Screw M8x20 2
B13 Spring Washer M8 2
B14 UV180309 Bracket 1
B15 Socket Head Button Screw M5x6 2
B16 UV180418 Limit Switch QKS8-9 1
B17 Spring Washer M5 4
B18 Cross Round Head Screw M5x30 2
B19 Control Box 1
B20 Emergency Stop Switch 1
B21 Stop Switch 1
B22 Start Switch 1
B23 Blade Speed Knob 1
B24 Cutting Mode Selection Switch 1
B25 Coolant ON/OFF Switch 1
B26 UV180303A See Through Plate 1
B27 Cross Round Head Screw M4x8 4
B28 UV180303 Plate 1
B29 Hex Nut M16 1
B30 Set Screw M6x8 1
B31 UV180216 Slide Bracket 4
B32 Socket Head Flat Screw M6x20 4
B33 UV180405 Tension Handle 1
B34 Lead Screw M12x120 1
B35 Flat Washer 12x28x3 1
B36 UV180307 Tap Washer 17
B37 UV180208 Bushing 1
B38 UV180409 Blade 19x0.9x2285 1
B39 Cross Round Head Screw M4x6 2
B40 UV180304 Tension Gauge 1
B41 UV180203A Adjustment Bracket 1
B42 Hex Nut M12 2
B43 Socket Head Cap Screw M8x16 2
B44 Set Screw M8x16 1
B45 UV180202A Fixed Bracket 1
B46 Spring Pin ø8x30 1
B47 UV180203 Tension Slide Bracket 1
B48 Socket Head Flat Screw M8x25 2
B49 UV180202 Shaft 1
B50 UV180506 Bearing 6204 2
B51 UV180105 Saw Wheel 1
B52 Flat Washer 8x25x3 2
B53 Spring Washer M8 2
B54 Socket Head Cap Screw M8x20 2
12

SECTION B - PARTS LIST
Part No. Stock No. Description Size Q'ty
B55 Hose 540mm 1
B56 UV180106 Rear Saw Wheel 1
B57 Hose Clamp 13mm 2
B58 9160408-1 Valve M9TM7 1
B59 Cross Round Head Screw M5x10 2
B60 9160321 Brace 1
B61 Hose 1660mm 1
B62 UV180315 Cover 1
B63 UV180509 Ball Bearing 6007 1
B64 UV180217 Bushing 1
B65 UV180506 Bearing 6204 1
B66 UV180204A Output Gear 1
B67 Key 6x6x20 1
B68 Key 6x6x4 1
B69 UV180204 Output Shaft 1
B70 UV180505 Ball Bearing 6200 3
B71 UV180510 Tape Bearing NK1212 2
B72 UV180206 Gear Shaft 1
B73 Key 5x5x8.2 1
B74 UV180206A Reducer Gear 1
B75 Key 5x5x12 1
B76 UV180205 Guide Shaft 1
B77 UV180205A Guide Gear 1
B78 Socket Head Cap Screw M6x40 2
B79 UV180102 Gear Box 1
B80 Socket Head Cap Screw M6x20 2
B81 UV180A313 Cover 1
B82 Pan Head Screw M4x8 6
B83 UV180A312 Wiring Box 1
B84 Cross Round Head Screw M5x45 2
B85 Wire Locker PG-9 3
B86 UV180207 Motor Shaft 1
B87 Spring Washer M6 4
B88 Socket Head Cap Screw M6x20 3
B89 Motor Housing 1
B90 UV180102B Motor Front Cover 1
B91 Socket Head Cap Screw M8x16 1
B92 UV180102A Motor Rear Cover 1
B93 Power Cord 1
B94 UV180306 Tube 1
B95 125-404 Trigger Handle (L) 1
B96 125-403 Trigger Handle (R) 1
B97 Pan Head Screw M4x8 4
B98 125408-1 Trigger Switch Button 1
13

14

SECTION C - PARTS LIST
Part No. Stock No. Description Size Q'ty
C01 UV180A302 Right Stand 1
C02 Hex Cap Screw M8x16 2
C03 Flat Washer M8 2
C04 UV180A304 Rear Stand 1
C05 UV180A305 Front Stand 1
C06 Hex Cap Screw M8x16 8
C07 331D4-37 Level Pad 1/2" 2
C08 Hex Nut 1/2" 2
C09 UV180A303 Left Stand 1
C10 Flat Washer M8 8
C11 Hex Nut M8 8
C12 UV180A301 Water Tray 1
C13 Flat Washer M8 2
C14 Hex Cap Screw M8x16 2
C15 Pump 1
C16 UV180A213 Position Rod 1
C17 UV180A308 Screen 1
C18 Big Round Head Screw M6x25 2
C19 UV180A306 Chip Tray 1
C20 UV180A307 Chip Tray 1
C21 Socket Head Cap Screw M5x12 3
C22 Cross Round Head Screw M4x6 2
C23 Drain Plug 3/8"PT 1
15

16

Axminster Tools & Machinery Ltd
Weycroft Avenue, Axminster, Devon EX13 5PH
axminster.co.uk
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling.Help to
protect the environment, take the packaging to the local recycling centre and place into the appropriate
recycling bin.
Do not dispose of electric tools together with household waste material. In observance of European
Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance
with national law, electric tools that have reached the end of their life must be collected separately and
returned to an environmentally compatible recycling facility.
Only for EU countries
Free Three Year Guarantee on Axminster Hobby,Trade and Industrial Series woodworking and
engineering machines, Axminster Air compressors and Air Tools,and bench top grinders - no
registration necessary just proof of purchase.
We will repair or replace at our discretion and will collect only from a UK mainland address,
irrespective of the original delivery address.
The Guarantee assumes that you have bought the correct machine for the required operation, in
accordance with our guidelines; have operated and maintained it in accordance with the instruction
manual; and that all cutting machines will be used with a blade which is sharp and serviceable at all
times. It does not cover consumable items purchased with the original product, including original
blades or abrasives.
The Axminster guarantee is available on
Hobby,Trade, Industrial, Engineer, Air Tools & CNC Technology Series machines
It’s probably the most comprehensive FREE guarantee ever- buy with confidence from Axminster!
So sure are we of the quality, we cover all parts and labour free of charge for three years!
• Look for the icon and put your trust in Axminster
• No registration necessary - just keep your proof of purchase
• Optional Service Plan for Industrial Series machinery
AXMINSTER
SERIES
Hobby
Great value & easy-to-use,
perfect for use at home
Quality, precision machines
for the workshop or education
Precision CNC machines for
industry and education
Solid, reliable machines
designed for daily use
Small machines for the home
engineer
Top performers with class leading features and
build quality for use in busy workshops
Tools for home or workshop
use; durable and great value
Normal wear and tear; misuse,abuse and neglect are excluded and the machine should not have been
modified in any way. Please do not attempt to service the product without first contacting us; we are
happy to guide you but failure to do so may invalidate the guarantee.
The Guarantee is transferable from owner to owner in the first three years but you must have original
proof of purchase.Should we need to replace a machine in the first three years the guarantee will still
continue to be effective from the original purchase date.
Full Terms and Conditions can be found at axminster.co.uk/terms
This guarantee does not affect your statutory rights.
For more information visit axminster.co.uk/3years