Axon POS3600 Series User manual

User Manual
June 2008 Revision 1.2b
Point – of - Sale
Hardware System

Copyright 2008 June
All Rights Reserved
Manual Version 1.2b
P/N: 48201273
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose. We shall not
be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights are
reserved. No part of this document may be photocopied, reproduced or translated to
another language without the prior written consent of the manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation. Microsoft®
and Windows® are registered trademarks of Microsoft Corporation.
2

Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrial power supply, turn off the power switch
and remove the power cord plug from the wall socket. The wall socket must be easily
accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart,stand,or table.The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation;to
ensure reliable operation of the product and to protect it from overheating. These
openings must not be blocked or covered.The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.This product should
never be placed near or over a radiator or heat register,or in a built-in installation unless
proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking
label.If you are not sure of the type of power available, consult your dealer or local
power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
CE MARK
This device complies with the requirements of the EEC directive 2004/108/EC
with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage
Directive”.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
3

CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only with the
same or equivalent type recommended by the manufacturer. Discard used batteries
according to the manufacturer’s instructions.
LEGISLATION AND WEEE SYMBOL
2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dustbin symbol on the device means that it should not be disposed of with
other household wastes at the end of its working life. Instead, the device should be taken to
the waste collection centers for activation of the treatment, collection, recycling and
disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract.
This product should not be mixed with other commercial wastes for disposal.
4

Revision History
Revision
Number Description Revision Date
1.0 Initial release 2007 March
1.1 System Disassembly updated 2007 May
1.2 Cover page updated
Connector Pin Definition updated
2007 September
1.2a Cash Drawer Power Setting Correction 2007 September
1.2b
Cash Drawer Power Setting Correction
Updated specification with Second
Display options
Updated Optional Items with Second
Display options
Updated LCD ID jumper settings
2008 June
5

Table of Contents
1. Item Checklist ..................................................................................................................7
1.1. Standard Items..........................................................................................................7
1.2. Optional Items...........................................................................................................7
2. System View.....................................................................................................................8
2.1. Front View.................................................................................................................8
2.2. Side View..................................................................................................................8
2.3. Rear View.................................................................................................................9
2.4. Bottom View..............................................................................................................9
2.5. I/O View..................................................................................................................10
3. Driver Installation ..........................................................................................................11
3.1. Driver List ...............................................................................................................11
3.2. Chipset Driver Installation.......................................................................................11
3.3. USB 2.0 Driver Installation OS Requirements ........................................................13
3.4. VGA Driver Installation............................................................................................15
3.5. POSTouch Driver Installation..................................................................................16
3.6. Audio Driver Installation..........................................................................................18
3.7. 10/100Mb LAN Driver Installation...........................................................................19
4. Peripherals Installation .................................................................................................21
4.1. Magnetic Card Reader Installation..........................................................................21
4.2. Cash Drawer Installation.........................................................................................22
5. System Disassembly.....................................................................................................24
5.1. Replacing HDD.......................................................................................................24
5.2. Replacing the CF Card Holder (Optional)...............................................................25
5.3. Replacing Mainboard & I/O Board..........................................................................25
5.4. Replacing Inverter Board & Touch Screen Board ...................................................26
6. Specification ..................................................................................................................28
7. Jumper Settings.............................................................................................................30
7.1. Connectors .............................................................................................................31
7.2. Jumper Settings......................................................................................................31
7.3. Connectors Pin Definition .......................................................................................33
8. BIOS Settings.................................................................................................................38
8.1. BIOS Setup Utility...................................................................................................38
8.2. Starting the BIOS Setup..........................................................................................38
8.3. When a Problem Occurs.........................................................................................38
8.4. BIOS Main Menu ....................................................................................................38
6

1. Item Checklist
Take the system unit out of the carton. Remove the unit from the carton by holding it by the
foam inserts. The following contents should be found in the carton:
1.1. Standard Items
a. Driver CD b. System
c. Power Cable d. User Manual
1.2. Optional Items
a. CF card holder b. MSR
c. 7" wide, 8.4", 10.4", 12.1" LCD
Second Display
7

2. System View
2.1. Front View
MSR
Power LED Power Switch Button
2.2. Side View
Tilt Angle 65°~ -25°
Ventilation slots
Pole type VFD
Small Footprint
8

2.3. Rear View
Rear I/O
2.4. Bottom View
Rubber Foot
VESA
mountin
g
holes
9

2.5. I/O View
Line in Line out USB
(
4
)
2n
d
VG
A
LAN
DC Jack Cash
Drawer COM
(
4
)
Parallel
Note: The maximum current that can be drawn from each COM port is 500 mA.
10

3. Driver Installation
3.1. Driver List Folder/File File Description
<CD>:\POS360_B78.htm B78 Driver List
<CD>:\COMMON\INTEL\Chipset Chipset Driver
<CD>:\COMMON\INTEL\USB 20 USB 2.0 Driver
<CD>:\COMMON\INTEL\VGA\i85x VGA Driver
<CD>:\COMMON\POS_Touch POSTouch Driver
<CD>:\COMMON\Ac97_codec\Realtek\ALC202A Audio Driver
<CD>:\COMMON\Lan_driver\R8139_810x 10/100Mb LAN Driver
-The following procedures are for Windows 2000/XP, other platforms are similar.
3.2. Chipset Driver Installation
a. Double click “infinst_enu_6.0.1.1002”
on the My computer window. b. Click the “Next” button on the Welcome window.
c. Click the “Yes” button on the License
Agreement window. d. Click the ”Next” button on the Readme Information window.
11

e. Click the “Finish” button and restart your
system.
12

3.3. USB 2.0 Driver Installation
OS Requirements
OS USB 2.0 requirements
Windows
XP USB 2.0 drivers are provided in Service Pack 1 (SP1) for Windows XP, which is available through Windows Update.
Windows
2000 USB 2.0 drivers are available through Windows Update or Service Pack 4.
Windows
98SE/Me USB 2.0 drivers are available on the Intel developer site.
Windows
98 (Retail)
Developers and OEMs should contact Orange Ware. For end-users,
if your device does not ship with Windows 98 drivers, contact your
device or system manufacturer. If USB 2.0 drivers are not available,
your device will operate at USB 1.1 speeds
Linux USB 2.0 support is available in kernel 2.4.19 or later development
kernels, or in the 2.4.19 or later production kernel. More information.
a. Right click My Computer on the desktop
and select “Properties” b. Select “Hardware”Æ”Device Manager” on System Properties.
c. Select ”Other Devices” Æ“Universal Serial Bus (USB) Controller” Æ”Properties” in
Device Manager.
13

d. Select “Device”Æ“Update Driver…”. e. Click the ”Next” button on the Welcome
window.
f. Select “Search for a suitable…”and click
the “Next” button on the Install Hardware
Device Drivers window.
g. Select “Specify a location” and click the
“Next” button on the Locate Driver Files
window.
h. Press “Browse” to select the driver and
then click the “OK” button to go to the next
page.
i. Click the “Next” button on the Driver
Files Search Results window.
14

j. Click the “Finish” button to complete this
process. k. Finished.
3.4. VGA Driver Installation
a. Click the “Win2K_XP” on the My
Computer window. b. Click the “v14.19.50” on the My Computer window.
c. Select “win2K_xp141950” on the
v14.19.50 window. d. Click the “Next” button on the Intel(R) Chipset Graphics Driver Software-
InstallShield(R) Wizard window.
15

e. Click the “Next” button on the Intel(R)
Graphics Media Accelerator Driver
window.
f. Click the “Yes” button on the Intel(R)
Graphics Media Accelerator Driver
window.
g. Select “Yes, I want to restart my
computer now” and click the “Finish”
button on the Intel(R) Graphics Media
Accelerator Driver window.
3.5. POSTouch Driver Installation
a. Double click the ”Setup” on the “My
Computer” window. b. Click the “Next“ button on the “Welcome window”.
16

c. Click the ”next” button on the “Wellcome”
window. d. Select “Install the software automatically” and click the ”Next” button on the
“URTC1000” window
e. Click the “Next” button on the “License
Agreement” window. f. Click the “Next” button on the “Install Folder” window.
g. Click the “Next “ button on the “Shortcut
Folder” window. h. Select the “USB” and click the ”Next” button on the “Options” window.
17

i. Click the :Next” button on the “Ready to
Install” window j. Click the “Continue Anyway” button on the URTC-1000 window
k. Click the “Finish” button on the
“Installation Successful” window . l. Click the “OK” button to reboot your computer
3.6. Audio Driver Installation
a. Click “A3.71” on the My Computer window. b. Double click “wdm_a371” on the My
Computer window.
18

c. Click “Next” button on the Realtek AC’97
Audio Setup window. d. Click “Yes” button on the Digital Signature Not Found window.
e. Click “Finish” button on the RealtekAC’97
Audio Setup window.
3.7. 10/100Mb LAN Driver Installation
a. Double click ”Setup” on the My
Computer window. b. Click the “Finish” button on the Maintenance Complete window.
19

c. Click the ”OK” button and restart your
system.
20