protech POS-3520 User manual

USER’S
MANUAL
POS-3520
15” POS System Powered by
Intel
®
Atom
®
D525 Platform
POS
-
3520
M
6

POS-3520 POS System
With LCD / Touchscreen
COPYRIGHT NOTICE
This user’s manual is meant to assist users in installing and setting up the
system. The information contained in this document is subject to change
without any notice.
This manual is copyrighted May 2011 (Revised Edition: July 2012). You may
not reproduce or transmit in any form or by any means, electronic, or
mechanical, including photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the property
of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void your
authority to operate such equipment.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And
therefore we strongly recommend that qualified engineers can open and disassemble the
system.
The LCD and Touchscreen are easily breakable, please handle them with extra care.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual .......................................................
1-2
1-2 POS System Illustration ................................................
1-3
1-3 System Specification .....................................................
1-4
1-4 Safety Precautions .........................................................
1-6
CHAPTER 2 SYSTEM CONFIGURATION
2-1 Jumper & Connector Quick Reference Table ...............
2-2
2-2 Component Locations ...................................................
2-3
2-3 How to Set the Jumpers ................................................
2-4
2-4 COM Port & VGA Connector ……………………….. 2-6
2-5 COM Port RI and Voltage Selection ………………… 2-9
2-6 Mini-DIN and USB Connector ………………………. 2-13
2-7 LAN & USB Connector ………………………………
2-14
2-8 Cash Drawer Connector ………………………………
2-15
2-9 Cash Drawer Power Selection ………………………...
2-16
2-10 Power LED Connector ………………………………….
2-17
2-11 Smart FAN Connector ….……………………………. 2-17
2-12 Power Connector …………………………………….. 2-17
2-13 Reset Switch Connector ……………………………… 2-18
2-14 Power for Thermal Printer Connector ………………...
2-18
2-15 External Speaker Connector …………………………..
2-18
2-16 Inverter Connector …………………………………… 2-19
2-17 MSR/ Card Reader Connector ……………………….. 2-20
2-18 Printer Connector ……………………………………. 2-20
2-19 LVDS Connector …………………………………….. 2-21
2-20 SATA Connector ……………………………………...
2-23
2-21 SATA Power Connector ………………………………
2-23
2-22 Touch Panel Connector ……………………………….
2-24
2-23 Touch Panel Selection ………………………………. 2-24
2-24 Clear CMOS Data Selection ………………….……… 2-25
2-25 Compact Flash Connector …………………………….
2-26

Contents
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction …...............................................................
3-2
3-2 Intel
®
Chipset Software Installation Utility …...............
3-3
3-3 VGA Driver Utility …………………………….…….. 3-4
3-4 LAN Driver Utility …....................................................
3-5
3-5 Sound Driver Utility …..................................................
3-6
3-6 Touch Screen Driver Utility …………………………..
3-7
3-7 Wireless Driver Utility (Optional) ……………………
3-8
CHAPTER 4 AMI BIOS SETUP
4-1 Introduction …...............................................................
4-2
4-2 Entering Setup …...........................................................
4-3
4-3 Main …………………………….….............................
4-5
4-4 Advanced …………………………...............................
4-6
4-5 Boot ………………………….......................................
4-16
4-6 Security Settings ……….…….......................................
4-20
4-7 Chipset ……………………..……………………….... 4-21
4-8 Exit ………………………............................................
4-25
APPENDIX A SYSTEM ASSEMBLY
Exploded Diagram for 2 Inch Thermal Printer Remove/ Install
A-2
Exploded Diagram for 3 Inch Thermal Printer Remove/ Install A-5
Exploded Diagram for MSR & Fingerprint Module Remove/
Install …………….…………………………………………..
A-8
Exploded Diagram for Fingerprint Module …………………. A-9
Exploded Diagram for POS-3520 Hard Disk Drive Remove/
Install ………………………………………………………..
A-10
Exploded Diagram for POS-3520 LCD Panel Remove/ Install ..
A-13
Exploded Diagram for POS-3520 Mini-PCIE Installation .…. A-15
Exploded Diagram for POS-3520 Motherboard ..…………… A-16
Exploded Diagram for POS-3520 MSR Module …….……… A-18
Exploded Diagram for POS-3520 MSR & LCD Assembly … A-20
Exploded Diagram for POS-3520 Printer Assembly …………
A-21
Exploded Diagram for POS-3520 Top Cover Assembly ........ A-23
Exploded Diagram for POS-3520 VFD Module Assembly ….
A-24

Contents
APPENDIX B TECHNICAL SUMMARY
Block Diagram .........................................................................
B-2
Interrupt Map ............................................................................
B-3
DMA Channels Map ................................................................
B-4
I/O Map ....................................................................................
B-5
Watchdog Timer Configuration ………………………………
B-8
Flash BIOS Update ………………………………………….. B-10

Page:1-1
INTRODUCTION
This chapter gives you the information for POS-3520. It also outlines
the system specifications.
Sections included:
About This Manual
POS System Illustration
System Specifications
Safety Precautions
Experienced users can jump to chapter 2 on page 2-1
for a quick start.
CHAPTER
1

Chapter 1 Introduction
Page: 1-2 POS-3520 USER
′ S MANUAL
1-1. ABOUT THIS MANUAL
Thank you for purchasing our POS-3520 system. The POS-3520 is an updated
system designed to be comparable with the highest performance of IBM AT
personal computers. The POS-3520 provides faster processing speed, greater
expandability and can handle more tasks than before. This manual is designed
to assist you how to install and set up the whole system. It contains four
chapters and two appendixes. Users can configure the system according to their
own needs.
Chapter 1 Introduction
This chapter introduces you to the background of this manual. It also includes
illustrations and specifications for the whole system. The final section of this
chapter indicates some safety reminders on how to take care of your system.
Chapter 2 System Configuration
This chapter outlines the location of motherboard components and their
function. You will learn how to set jumper and how to configure the system to
meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the Intel
Utility, VGA Utility, LAN Utility, Sound Utility, and Touch Screen Utility.
Chapter 4 AMI BIOS Setup
This chapter indicates you how to change the BIOS configurations.
Appendix A System Assembly
This appendix gives you the exploded diagrams and part numbers of the POS-
3520.
Appendix B Technical Summary
This appendix gives you the information about the allocation maps for the
system resources, Watchdog Timer Configuration, and Flash BIOS Update.

Chapter 1 Introduction
POS-3520 USER ′ S MANUAL Page: 1-3
1-2. POS SYSTEM ILLUSTRATION
Front
V
iew
Rear View
Side View
Bottom View Quarter View

Chapter 1 Introduction
Page: 1-4 POS-3520 USER
′ S MANUAL
1-3. SYSTEM SPECIFICATIONS
MAINBOARD (PROX3520LF)


CPU Type:
Intel
®
ATOM™ Pineview D525


Chipset:
Intel
®
ICH8M


Memory:
2 x DDR3 SO-DIMM Slot, 1G DDR3 SO-DIMM default (up to 4GB)


Cache:
Depended on CPU


Real-Time Clock / Calendar:
Embedded in Intel
®
ICH8M South Bridge


BIOS:
AMI BIOS


Keyboard Connector:
PS/2 Keyboard, with mini DIN connecter on rear panel .


Mouse Connector:
PS/2 Mouse, with mini DIN connecter on rear panel .


Serial Port:
3 x DB-9 & 1 x RJ45, +5V/ 12V selectable


Universal Serial BUS Port:
5 x USB ports


LAN Function:
1 x 10/100/1000 Mbps


Audio Function:
1 x 2W Speaker

Chapter 1 Introduction
POS-3520 USER ′ S MANUAL Page: 1-5


VGA Function:
1 x DB-15 VGA interface


Dimension (W x H x D):
356 x 309 x 167 mm (14.02" x 12.17" x 6.57")


System Weight:
5.7 kg


LCD Panel:
Type
XGA
Max. Resolution
1024 x 768
Size/Type
15” / TFT
Viewing Angel (degree)
+80 ° ~-80 ° horizontal
+70 ° ~-60 ° vertical
Brightness
250 cd / m
2
Signal Interface (bit)
TTL (24-bit)


Touch Panel:
15” 5wire Analog resistive .


Printer:
2” or 3” easy loading thermal printer with Auto cutter
(* Diameter of paper roll can not exceed 8 cm.)


I-Button (Optional):
Read only, output through PS/2 KB interface


MSR (Optional):
JIS-I or II, ISO Tracker 1+2+3 (PS/2 KB Interface)


Wireless LAN (Optional):
Mini PCIe Wireless LAN Module (802.11b/g/n, 1T1R)


Fingerprint (Optional):
Embedded Fingerprint module (USB interface)

Chapter 1 Introduction
Page: 1-6 POS-3520 USER
′ S MANUAL
1-4. SAFETY PRECAUTIONS
The following messages are safety reminders on how to protect your systems
from damages, and extending the life cycle of the system.
1. Check the Line Voltage
a. The operating voltage for the power supply should be within the range of
100V to 240V AC; otherwise the system may be damaged.
2. Environmental Conditions
a. Place your POS-3520 on a sturdy, level surface. Be sure to allow enough
space around the system to have easy access needs.
b. Avoid installing your POS-3520 system in extremely hot or cold places.
c. Avoid exposure to sunlight for a long period of time (for example, in a
closed car in summer time. Also avoid the system from any heating
device.). Or do not use the POS-3520 when it has been left outdoors in a
cold winter day.
d. Bear in mind that the operating ambient temperature is between 0°C and
35°C (32°F and 95°F).
e. Avoid moving the system rapidly from a hot place to a cold place, and
vice versa, because condensation may occur inside the system.
f. Place your POS-3520 against strong vibrations, which may cause hard
disk failure.
g. Do not place the system too close to any radio-active device. Radio-
active device may cause signal interference.
h. Always shutdown the operation system before turning off the power.
3. Handling
a. Avoid placing heavy objects on the top of the system.
b. Do not turn the system upside down. This may cause the hard drive to
malfunction.
c. Do not allow any objects to fall into this product.
d. If water or other liquid spills into the product, unplug the power cord
immediately.

Chapter 1 Introduction
POS-3520 USER ′ S MANUAL Page: 1-7
4. Good Care
a. When the outside case gets stained, remove the stains using neutral
washing agent with a dry cloth.
b. Never use strong agents such as benzene and thinner to clean the surface
of the case.
c. If heavy stains are present, moisten a cloth with diluted neutral washing
agent or alcohol and then wipe thoroughly with a dry cloth.
d. If dust is accumulated on the case surface, remove it by using a special
vacuum cleaner for computers.

Page 2-1
SYSTEM
CONFIGURATION
Helpful information that describes the jumper and connector
settings, and component locations.
Sections included:
Jumper & Connector Quick Reference Table
Component Locations
Configuration and Jumper settings
Connector Pin Assignments
CHAPTER
2

Chapter 2 System Configuration
Page: 2-2 POS-3520 USER
’ S MANUAL
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
Connector & Jumper Name Page
COM Port & VGA Connector COM1, COM3, COM4, COM2-1,
JVGACOM2
2-6
COM Port RI and Voltage Selection JP_COM1, JP_COM2, JP_COM3,
JP_COM4
2-9
MINI-DIN and USB Connector JPS2USB1, USB5, USB6 2-13
LAN & USB Connector JRJ45USB1 2-14
Cash Drawer Connector DRW1, DRW2 2-15
Cash Drawer Power Selection JP14, JP17 2-16
Power LED Connector LED-1 2-17
Smart Fan Connector FAN2 2-17
Power Connector FAN1 2-17
Reset Switch Connector JRST1 2-18
Power for Thermal printer Connector PRT_PWR1 2-18
External Speaker Connector SPK1 2-18
Inverter Connector INV1, INV2 2-19
MSR/ Card Reader Connector PS2 2-20
Printer Connector LPT1 2-20
LVDS Connector LVDS1, LVDS2 2-21
SATA Connector SATA1 2-23
SATA Power Connector JPWR_4P1 2-23
Touch Panel Connector TOUCH1 2-24
Touch Panel Selection JP16 2-24
Clear CMOS Data Selection JP1 2-25
Compact Flash Connector CF1 2-26

Chapter 2 System Configuration
POS-3520 USER ’ S MANUAL Page: 2-3
2-2. COMPONENT LOCATIONS
2
41
3
1
23
4
5
61
2
5
6
1
2
2
16
5
5
6
1
2
5
6
1
2
1
4
9
13
14
12
85
21 24
20
16
1
2
5
6
1
69
5
1
2
5
6
COM3
9 1
10 212
3
4
PWR_IN1
1
3
1
3
1
2
1
2
21
78
2
1
7
8
1
11
1
1
1
4
1
2
3
4
1
7
1
4
1
415
9 1
10 2
203
73
2
72 71
74
1
204
203
73
2
72 71
74
1
204
1
19
20
2
1
29
30 2
17
1
4
1
2
3
15
1 6
5
1
106
1
2
14
2
1 9
10
1
14
13
26
1
3
POS-3520 Connector, Jumper and Component locations

Chapter 2 System Configuration
Page: 2-4 POS-3520 USER
’ S MANUAL
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting the jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by using
a small plastic "cap", Also known as the jumper cap (with a metal contact
inside), you are able to connect the pins. So you can set-up your hardware
configuration by "opening"or "closing"pins.
The jumper can be combined into sets that called jumper blocks. When the
jumpers are all in the block, you have to put them together to set up the
hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins for example, labelled PIN1, PIN2, and PIN3. You
can connect PIN1 & PIN2 to create one setting and shorting. You can either
connect PIN2 & PIN3 to create another setting. The same jumper diagrams
are applied all through this manual. The figure below shows what the manual
diagrams look and what they represent.

Chapter 2 System Configuration
POS-3520 USER ’ S MANUAL Page: 2-5
JUMPER DIAGRAMS
JUMPER SETTINGS

Chapter 2 System Configuration
Page: 2-6 POS-3520 USER
’ S MANUAL
2-4. COM PORT & VGA CONNECTOR
There are four COM ports enhanced in this board namely: COM1,
COM2, COM3 and COM4.
Caution: When using a 72W power adaptor, do not set the voltage at
“12V” for three COM ports or above; otherwise, the system
may shut down due to power deficiency.
COM1: COM1 Connector
The COM1 Connector assignments are as follows:
PIN ASSIGNMENT
1 DCD2
2 RXD2
3 TXD2
4 DTR2
5 GND
6 DSR2
7 RTS2
8 CTS2
9 RI / +5V / +12V selectable
COM3: COM3 Connector
The pin assignments are as follows:
PIN ASSIGNMENT
1 DCD3
2 RXD3
3 TXD3
4 DTR3
5 GND
6 DSR3
7 RTS3
8 CTS3
9 RI / +5V / +12V selectable
10 NC
COM3
COM1

Chapter 2 System Configuration
POS-3520 USER ’ S MANUAL Page: 2-7
COM4: COM4 Connector
The pin assignments are as follows:
PIN ASSIGNMENT
1 DCD4
2 RXD4
3 TXD4
4 DTR4
5 GND
6 DSR4
7 RTS4
8 CTS4
9 RI / +5V / +12V selectable
10 NC
COM2-1: COM2 External Connector
The pin assignments are as follows:
PIN ASSIGNMENT
1 DCD1
2 RXD1
3 TXD1
4 DTR1
5 GND
6 DSR1
7 RTS1
8 CTS1
9 RI / +5V / +12V selectable
10 NC
COM4
6
10
1
5
COM2_1
5
1
10
6