Axor Citterio Select 230 2jet sBox 39862007 User manual

INSTALLATION
ZH ⁄ 用户手册 ⁄ 组装说明 02
EN ⁄ Instructions for use ⁄ assembly instructions 03
Lesezeichen
中文 02
English 03
AXOR Citterio Select 230 2jet sBox
39862007

02
安装 (参见第页 04)
ZH
安全技巧
装配时为避免挤压和切割受伤，必须戴上手套。
冷热水管间过大的压力差必须予以平衡。
安装提示
⁄ 安装前必须检查产品是否受到运输损害。 安装后
将不认可运输损害或表面损伤。
⁄ 管道和阀门必须根据通用标准进行安装、冲洗和
检查。
⁄ 请遵守当地国家现行的安装规定。
⁄ 首次调试时和维护作业之后，管接头中的空气可
能产生噪音。大约使用管接头 15 次后噪音消失。
技术参数
工作压强： 最大 1 MPa
推荐工作压强： 0,1 - 0,5 MPa
测试压强： 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
热水温度： 最大 60°C
热力消毒: 70°C ⁄ 4 分钟
该产品专为饮用水设计！
符号说明
请勿使用含有乙酸的硅胶！
调节 (参见第页 11 )
热水温度调节。如果使用即热式喷头，则不
建议安装热水阀门。
保养 (参见第页 15)
单向阀必须在符合国家或当地的法律的情况
下按照EN 806-5定期检查 (至少一年一次) 。
大小 (参见第页 17)
流量示意图 (参见第页 17 )
备用零件 (参见第页 18 )
选装附件 (不在供货范围内)
加长件 #43333000 (参见第页 14)
清洗 (参见第页 12 )
操作 (参见第页 16)
⁄ 汉斯格雅建议，清晨或在水流长时间停滞
后，前半升水不作饮用水使用。
⁄ 通过手柄打开阀门时出水口可能流出少量
水。
⁄ 抬起把手打开龙头，并调节需要的水温。
通过位于正面出水口的调节钮可以暂时停
止水流。长时间不使用时，例如夜晚或房
屋空置，则必须将把手完全关闭。
问题 原因 补救
⁄龙头不灵活 ⁄ 阀芯损坏，结垢 ⁄ 更换阀芯
⁄龙头滴水 ⁄ 阀芯损坏 ⁄ 更换阀芯
⁄水从螺纹底座中流出 ⁄ 连接软管没有完全旋入基体 ⁄ 用手拧紧连接软管
⁄ 连接软管的O形环损坏 ⁄ 更换O形环
⁄热水温度过低 ⁄ 温度限制器设置错误 ⁄ 设置温度限制器
⁄更换龙头后，在打开可调龙头时流
量减少 ⁄ 安装了错误的可调龙头 ⁄ 更换可调龙头 (#98463000)
⁄调节按钮不好用 ⁄ 调节按钮脏污 ⁄ 清洁调节按钮，给 O 形环 14x1,5
上油 (参见第页 18 )

03
ASSEMBLY (see page 04 )
EN
SAFETY NOTES
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The hot and cold supplies must be of equal pressures.
INSTALLATION INSTRUCTIONS
⁄ Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
⁄ The pipes and the fixture must be installed, flushed and
tested as per the applicable standards.
⁄ The plumbing codes applicable in the respective
countries must be observed.
⁄ During initial start-up and after servicing, air in the
fittings can cause noise. After switching the jet on and
off about 15 times, the noise will stop.
TECHNICAL DATA
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Thermal disinfection: 70°C ⁄ 4 min
The product is exclusively designed for drinking water!
SYMBOL DESCRIPTION
Do not use silicone containing acetic acid!
ADJUSTMENT (see page 11 )
To adjust the hot water limiter. Using a hot water
limiter in combination with a continuous flow
water heater is not recommended.
MAINTENANCE (see page 15 )
The check valves must be checked regularly
according to EN 806-5 in accordance with
national or regional regulations (at least once a
year).
DIMENSIONS (see page 17)
FLOW DIAGRAM (see page 17)
SPARE PARTS (see page 18 )
SPECIAL ACCESSORIES
(order as an extra)
extension #43333000 (see page 14 )
CLEANING (see page 12 )
OPERATION (see page 16 )
⁄ Hansgrohe recommends not to use as drinking
water the first half liter of water drawn in the
morning or after a prolonged period of
non-use.
⁄ Minor leaking may occur briefly at the spout
when opening the fitting via the lever.
⁄ Use the lever to open the tap and set the
desired temperature. The water flow can be
paused by pressing the Select button on the
face side of the spout. When the tap is not
used for a longer period of time, f.e. when
retiring at night or leaving the house, it must be
closed completely by means of the lever.
FAULT CAUSE REMEDY
⁄ Mixer stiff ⁄ Cartridge defective, calcified ⁄ Exchange cartridge
⁄ Mixer dripping ⁄ Cartridge defective ⁄ Exchange cartridge
⁄ Water escaping at the threaded base ⁄ connection hoses not completely
screwed into basic body
⁄ Tighten connection hoses by hand
⁄ O-ring at the connection hose defec-
tive.
⁄ Exchange O-ring
⁄ Hot water temperature too low ⁄ Hot water limiter incorrectly set ⁄ Set hot water limiter
⁄ Low flow with Select valve after valve
replacement
⁄ Improper Select valve installed ⁄ Replace Select valve (#98463000)
⁄ Select button stiff ⁄ Select button soiled ⁄ Clean Select button and grease
14x1,5 O-ring (see page 18 )

04
SW 24 mm
(4 Nm)
1.
2.
SW 10 mm
SW 19 mm
(4 Nm)
3.
max. 35 mm
1a 2
3
(3 Nm)
max. 60 mm
1b
150°
110°
5a
5b
4
Montage

05
150°
45°
105°
75° 75°
45°
105°
24 x 15°
5a
Montage

06
24 x 15°
5b
110°
25° 85°
55° 55°
25°
85°
110°
Montage

07
6
SW 17 mm
(8 Nm)
SW 22 mm
1.
2.
9
SW 17 mm
7
8
SW 22 mm
SW 22 mm
SW 19 mm
(4 Nm)
96507000
(450 mm)
1.
10 11
Armaturenfett
Grease
䀵滑油
Montage

08
1.
2.
3.
12
15
17
1.
2.
13
14
16
Montage

09
max. ± 20°
19a
19b
18
max. 30 mm
max. 30 mm
max. 30 mm
Montage

10
max. ± 20°
19c
F12
43333000
19d
max. ± 20°
> 2 min
21
1.
2.
22
1.
2.
20
Montage