Ayrton Arcaline3 User manual

Manuel d’utilisation
KEEP THIS MANUAL FOR FUTURE NEEDS

ARCALINE 3 User Manual XM1362-V1.0-NR
1
CONTENTS
1. SAFETY INSTRUCTIONS 2
2. FEATURES 3
3. FIXTURE OVERVIEW 5
4. DIMENSIONAL DRAWINGS 6
5. INSTALLATION 7
6. DMX-512 CONTROL CONNECTION 10
7. DEVICE DMX START ADDRESS SELECTION 11
8. DISPLAY 11
10. DMX PROTOCOL 18
11. ERROR MESSAGES 23
12. CLEANING AND MAINTENANCE 24
!
!
!
!
!
!
!
!
!
!
!
!
!

ARCALINE 3 User Manual XM1362-V1.0-NR
2
1. SAFETY INSTRUCTIONS
1.1. IMPORTANT SAFETY WARNING
This device has left the factory in perfect condition. In order to maintain this condition and to
ensure safe operation, it is absolutely necessary for the user to follow the safety instructions and
warning notes written in this user manual.
In order to install, operate, and maintain the lighting fixture safely and correctly we suggest that
the installation and operation be carried out by qualified technicians and these instructions be
carefully followed.
CAUTION!
HIGH VOLTAGE. RISK OF SEVERE OR FATAL ELECTRIC SHOCK
CAUTION!
ALWAYS DISCONNECT MAINS SUPPLY BEFORE REMOVING ANY FIXTURE
COVERS
CAUTION!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE. SENSITIVE PERSONS
MAY SUFFER AN EPILEPTIC SHOCK
CAUTION!
NEVER TOUCH THE DEVICE DURING OPERATION! COVERS MAY BE HOT
Important:
Damage caused by the disregard of this user manual is not subject to warranty. The
dealer and manufacturer will not accept liability for any resulting defects or problems.
•If the device has been exposed to temperature changes due to environmental conditions,
do not power on immediately. The resulting condensation could damage the device. Leave
the device powered off until it has reached room temperature.
•This device falls under protection-class I. Therefore, it is essential that the device be
earthed.
•If either lenses or display are damaged (damage may include cracks or gashes in the
material) they must be replaced.
•Electrical connections, such as replacing the power plug, must be performed by a
qualified person.
•Make sure that the available voltage is not higher than that which is stated at the end of
this manual.
•Make sure the power cord is never crushed or damaged by sharp edges. Should the power
cord suffer If this should be the case, replacement of the cable must be done by an
authorized dealer.
•If the external flexible power cord of this device is damaged, it shall be exclusively
replaced by the manufacturer or their service agent or a similar qualified person in order
to avoid injury.



ARCALINE 3 User Manual XM1362-V1.0-NR
3
•When the device is not in use or before performing maintenance, always disconnect the
device from the mains. Only handle the power cord from the plug. Never pull the plug out
of a socket by tugging the power cord.
•When powered on for the first time, some smoke or smell may occur. This is caused by
coating on metal parts when heated and is normal. If you are concerned, please contact
your distributor.
•Do not focus the beam onto flammable surfaces. The minimum distance between the
exiting lens of the device and the illuminated surface must be greater than 0.5 meter.
Please be aware that damage caused by any modifications to the device are not subject to
warranty. Keep away from children and non-professionals.
1.2. GENERAL GUIDELINES
•This device is a lighting effect for professional use on stages, in discotheques, theatres,
etc., the device was designed for indoor or outdoor use.
•This fixture is only allowed to be operated within the maximum alternating current as
stated in the technical specifications in section 2 of this manual.
•Handle the device with care, avoid shaking or using force when installing or maintaining
the device.
•When choosing the installation location, please make sure that the device is not exposed
to extreme heat, moisture or dust.
•If you use the quick lock cam when rigging the device, make sure the quick lock fasteners
are located in the quick lock holes correctly and securely.
•Operate the device only after having familiarized yourself with its functions. Do not
permit operation by persons not qualified for operating the device. Most damages are the
result of unprofessional operation.
•Please use the original packaging if the device is to be transported.
•The applicable temperature for the device is between -10°C to 45°C. Do not use the
device outside of this temperature range.
For safety reasons, please be aware that all modifications to the device are forbidden.
If this device is operated in any way different to the ones described in this manual, the
product may suffer damage and the warranty becomes void. Furthermore, any other
operation may lead to short-circuits, burns, electric shocks etc.
2. FEATURES
POWER SUPPLY
•AC 100-240V~ 50-60Hz
•Power Consumption: 180W

ARCALINE 3 User Manual XM1362-V1.0-NR
4
OPTICS
•LED: 12x10W High-Power LEDs, RGBW 4 in 1 LED make extremely even and smooth
color mixing effect
•RGBW 4 in 1 LED make extremely even and smooth color mixing effect
•Extremely long Life: 50,000H and low power consumption
COLORS
•Excellent color mixing and rainbow effect
•Color temperature linear adjust from 2700K to 8000K, preset color temperature scenes with:
2700K, 3200K, 4300K, 5600K, 6500K, 8000K options
FEATURES
•3 Control channel modes: 13 / 6 / 9 channels
•2 operations modes: DMX-512, Master / Slave modes
•Pixel Control: can make extremely chasing effect
•Strobe effect with 1-25 flashes per second and pulse effect
•General dimming and blackout for all four colors
•IP65 outdoor use
DISPLAY
•Advanced and convenient full –color LCD touch screen
•Locked automatically after standby for 15 seconds to prevent error; hold the button for 3
seconds to activate
SOFTWARE
7 pre-installed programs available upon selection
Upgrades: fast and convenient through DMX cable
Reset DMX address, remote lamp switch, reset can all be done by the controller
OTHER SPEC
Input signal isolation: guarantees stable signal transmission without interference
Advanced RDM function
WHIGHT
Net weight: 11 kg

ARCALINE 3 User Manual XM1362-V1.0-NR
5
3. FIXTURE OVERVIEW
-
1Body of the unit
2Glass
3Display
4Mode/esc- button
5Down-button
6Right-button
7Up-button
8Valve
9Hook for safty cable
10Power out
11Power in

ARCALINE 3 User Manual XM1362-V1.0-NR
6
4. DIMENSIONAL DRAWINGS

ARCALINE 3 User Manual XM1362-V1.0-NR
7
5. INSTALLATION
CAUTION!
DO NOT OPERATE THIS DEVICE WITH OPEN COVER
5.1. RIGGING THE DEVICE
CAUTION!
PLEASE CONSIDER THE GB7000.1-2015, GB7000.217-2008 AND THE OTHER
RESPECTIVE NATIONAL NORMS DURING THE INSTALLATION. THE
INSTALLATION MUST ONLY BE CARRIED OUT BY A QUALIFIED PERSON.
•The structure on which the device is rigged must be able to support 10 times the weight of
the device for 1 hour without any critical deformation occurring.
•The installation must always be secured with a secondary safety attachment, e.g. the
included appropriate safety cable.
•Never stand directly below the device when rigging, de-rigging or maintaining the device.
•All electrical connections should be approved by a qualified electrician prior to using the
product.
•When the device is permanently installed these installations have to be approved by a
qualified person once a year.
•Overhead rigging requires extensive experience, including (but not limited to) calculating
working load limits, specifying installation/ rigging materials, and periodic safety
inspection of all installation material as well as the device. If you lack these qualifications,
do not attempt the rigging of this device yourself. Improper installation/ rigging can result
in serious bodily injury.
•Before rigging make sure that the installation area can hold a minimum point load of 10
times the device’s weight.

ARCALINE 3 User Manual XM1362-V1.0-NR
8
5.2. RIGGING USING THE OMEGA BRACKETS
In the event that the unit is to be fixed to a tubular structure, the stands supplied with the
ARCALINE 3 can be replaced with tube clamps and fixed to the unit by corresponding
screws/nuts (clamps and hardware not included).
The following illustration shows an ARCALINE 3 fitted with tube clamps :
Important:
This step is very important to ensure safe rigging of the fixture.
5.3. Orientation of the unit
The floor stands can be installed in two different ways. It is therefore possible to obtain two
types of directional settings on the unit, as shown in the following diagrams :



ARCALINE 3 User Manual XM1362-V1.0-NR
9
5.4. Installation of the diffuser filters on the ARCALINE 3
The ARCALINE 3 can be fitted with specially-designed diffuser filters, enable the angle of
the unit’s beam to be adjusted, depending on the application for which it is intended.
CAUTION!
ONLY USE ORIGINAL AYRTON FILTERS IN THE ARCALINE 3
The ARCALINE 3 has an internal filter holder to house the diffuser filters.
These specially-designed diffuser filters are manufactured by AYRTON and are available in
several versions, depending on the diffusion Angle required. They come in the form of a kit with
two 2 translucent plates, each covering half of the projector’s LED groups.
In order to install the filters, each plate must be inserted into the unit on one end, and both sides
of the projector must therefore be opened.
Details of the filters installation :
•Unscrew the three HEX screws (number 1) with the help of a 2.5 mm hex key
•Remove the removable casing (number 2)
•Unscrew the two screws (number 3) using a Philips screwdriver
•Remove the plate (number 4) covering access to the filter housing, as well as its waterproof
seal (number 5)
•Take a filter and remove the protective films stuck to each side. From then on take care to
hold the filter by the edges and avoid touching the sides
•Insert the filter fully into the housing provided for this purpose (see diagram below), making
sure the granular side of the filter faces the glass on the unit.

ARCALINE 3 User Manual XM1362-V1.0-NR
10
•Replace the plate (number 4) covering access to the filter housing and its waterproof seal
(number 5), then screw the parts in place by tightening the two Philips head screws (number
3)
•Place the removable casing (mark 2) and fix to the unit by tightening both HEX screws
(number 1) Repeat this procedure to install the second filter on the other side of the unit
6. DMX-512 CONTROL CONNECTION
Connect the provided male side of the XLR cable to the female XLR output of your controller
and the female side of the XLR cable to the male XLR input of the device. You can connect
multiple devices together in a serial fashion. The cable needed should be two core, screened cable
with XLR input and output connectors. Please refer to the diagram below.

ARCALINE 3 User Manual XM1362-V1.0-NR
11
7. DEVICE DMX START ADDRESS SELECTION
All fixtures should be given a DMX starting address when using a DMX signal, so that the
correct fixture responds to the correct control signals. This digital starting address is the channel
number from which the fixture starts to “listen” to the digital control information sent out from
the DMX controller. The allocation of this starting address is achieved by setting the correct
address number on the display located on the base of the device.
You can set the same starting address for all fixtures or a group of fixtures, or set different
addresses for each fixture individually.
If you set the same address on all devices, all the devices will start to “listen” to the same control
signal from the same channel number. In other words, changing the settings of one channel will
affect all the fixtures simultaneously.
If you set a different address, each unit will start to “listen” to the channel number you have set,
based on the quantity of control channels of the unit. That means changing the settings of one
channel will affect only the selected device.
In the case of the led fixtures, which is a 13 channel fixture, you should set the starting address of
the first unit to 1, the second unit to 14(13 + 1), the third unit to 27 (13+ 14), and so on.
8. DISPLAY
The Display offers several features: you can set the starting address, run the pre-programmed
program or reset the device.
The main menu is accessed by pressing the -button until the display starts flashing. Browse
through the menu by pressing the -button , -button . Press the -button in order
to select the desired menu. You can change the selection by pressing the -button ,
-button. Confirm every selection by pressing the -button. You can leave every mode by
pressing the -button. After accessing the edit mode, the unit will automatically exit to the
main menu after 15 seconds from the last button press. When the unit is powered on, if no data
signal is connected after 1 minute, then the display will switch off automatically.

ARCALINE 3 User Manual XM1362-V1.0-NR
12
Default settings shaded
Address
Set Dmx
Address
A001~AXXX
DMX address setting
Users Mode
User Mode
Stand Mode
Basic Mode
Extend Mode
Pixel Mode
User Mode A
User Mode B
User Mode C
User’s mode to change
channel numbers
Edit
UserModeA
:
Max channel
Auto Prog
:
Preset User modes
A,B,C
:
Options
Status
No DMX Mode
Close/Hold/Auto
Auto run if no DMX
Service PIN
Service PIN
RDM UID
Set Type
Change To BIN
Password=XXX
Xxxxxx
LED BIN
LED BIN
Service
Password”=050”
RDM PID Code LED
BIN
LED BIN
Disp.Setting
Shutoff Time
Flip Display
Key Lock
DispFlash
02~60m 05m
ON/OFF
ON/OFF
ON/OFF
Display shutoff time
Reverse 180 degree
Key Lock
DispFlash
Flip Pixel
ON/OFF
LED reverse order
Temp. C/F
Celsius
Fahrenheit
Temperature switch
between /
Trigger
DMX Value Disp.
Set To Slave
Auto Program
Auto Prog……
Slave1,Slave2,Slave3
Master / Alone
DMX Value Disp.
Set To Slave
Auto Program
ResetDefault
ON/OFF
Restore factory set.
Info
Time Info.
Current Time
Ttl Life Hrs
Last Run Hrs
Timer PIN
Clr Last Run
XXXX(Hours)
XXXX(Hours)
XXXX(Hours)
Password=XXX
ON/OFF
Temp. Info
Head Temp.
XXX/
Software Ver
V x.x.x
Software version
Test
Test Channel
Auto Prog……
Test function
Manual Ctrl.
Auto Prog =XXX
:
Fine adjustment of the
lamp

ARCALINE 3 User Manual XM1362-V1.0-NR
13
9.1. Address
Set DMX Address
With this function, you can adjust the desired DMX-address via the Display.
1. Access the main menu.
2. Tap the <Up/Down> button until “Set DMX Address” is displayed.
3. Press ENTER, the display will show “Set DMX Address”.
4. Tap the <Up/Down> button, the display will show “A001~AXXX”
5. Press ENTER to confirm or press <MODE/ESC> to return to the main menu.
9.2. USERS MODE
9.2.1. User Mode
1Tap <MODE/ESC> button, access the main menu, Tap the <Up/Down> button until
“Users mode” is displayed. Press <ENTER>, the display will show “Users mode”.
2The display shows “User Mode” , Press <Up/Down> button, then you can choose “Edit
User Mode A”, “Edit User Mode B” and “Edit User Mode C”.
3Press <ENTER> to confirm or press <MODE/ESC> to exit
As well as Standard Mode, Basic Mode and Extended Mode, this fixture has another three
DMX modes which can be set according to user's needs. To set one of these user modes see
below:
1Tap <MODE/ESC> button, access the main menu, Tap the <Up/Down> button until
“Users mode set” is displayed. Press <ENTER>, the display will show “Users mode
set”.
2Choose “Edit User Mode A”, press “ENTER”
3Set “Max Channel=xxx” the max channel
4Set “Edit User Mode B” and “Edit User Mode C” as above
9.2.2. Edit User Mode A
With this function, you can adjust the rest user defined channel order.
1Tap <MODE/ESC> button, access the main menu, Tap the <Up/Down> button until
“Users mode” is displayed. Press <ENTER>, the display will show “Users mode”.
2The display show “Edit User Mode A” first channel, Press <Up/Down> the display will
show “Edit User Mode A”.
3Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.3. Options
9.3.1. Status
No DMX Mode
With this function, when the drive is not DMX signal, it runs automatism, close, hold and
music, the default is hold.
1. Access the main menu.
2. Press <Up/Down>, the display will show No DMX Mode.
3. Press< ENTER>, the display will show No DMX Mode.
4. The display show Hold,Press <Up/Down>, the display will show “Close”, “Auto”,
“Music”.
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

ARCALINE 3 User Manual XM1362-V1.0-NR
14
9.3.2. Service PIN
Service PIN——The Password for this function is “50”.
RDM UID—— With this function you can call up various submenus via RDM.
This device is RDM ready. RDM stands for "remote device management" and makes
remote control of devices connected to the DMX-bus. ANSI E1.20-2006 by ESTA
specifies the RDM standard as an extension of the DMX512 protocol.
Manual settings like adjusting the DMX starting address are no longer needed. This is
especially useful when the device is installed in a remote area.
RDM ready and conventional DMX devices can be operated in one DMX line. The RDM
protocol sends own packages in the DMX512 data feed and does not influence conventional
devices.
If DMX splitters are used and RDM control is to be used, these splitters must support RDM.
The number and type of RDM parameters depend on the RDM controller being used.
Set Type
1. Access the main menu.
2. Press <Up/Down>, the display will show Set Type.
3. Press< ENTER>, the display will show Set Type.
4. The display show “LED BIN”.
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
Change TO BIN
1. Access the main menu.
2. Press <Up/Down>, the display will show Change TO BIN.
3. Press< ENTER>, the display will show Change TO BIN.
4. The display show “LED BIN”.
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.3.3. Display Setting
Shut off time
With this function you can shut off the LCD display after 2 to 60 minutes.The default is 5
minutes.
Flip Display
With this function you can rotate the display by 180°.
1Tap <MODE/ESC> buttonaccess the main menuTap the <Up/Down> button until
“Options” is displayed. Press ENTER, the display will show “Options”. Tap the
<Up/Down> button until the display will show “Display Setting”. Press ENTER, the
display will show “Display Setting”.
2Press <Up/Down>, the display will show “Flip Display”.
3Press< ENTER>, the display will show “Flip Display”.
4The display show “OFF”, Press <Up/Down>, the display will show “ON”
5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.

ARCALINE 3 User Manual XM1362-V1.0-NR
15
Key Lock
With this function you can activate the automatic key lock function. If this function is
activated, the keys will be locked automatically after exiting the edit mode for 15 seconds.
keeping press the <MODE/ESC> key for 3seconds if you do not need this function.
1Tap <MODE/ESC> buttonaccess the main menuTap the <Up/Down> button until
“Personality” is displayed. Press < ENTER>, the display will show “Personality”. Tap
the <Up/Down> button until the display will show “Display Setting”. Press ENTER, the
display will show “Display Setting”.
2Press <Up/Down>, the display will show “Key Lock”.
3Press< ENTER>, the display will show “Key Lock”.
4The display show “OFF”, Press <Up/Down>, the display will show “ON”.
5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
Displ Flash
With this function you can the entire display to be flipped by 180˚ to allow for better view
when the fixture is hung from truss or a ceiling. This function is disabled as default.
1Tap <MODE/ESC>button access the main menu Tap the <Up/Down>button
until ”Personality” is displayed. Press ENTER, the display will show “Personality”. Tap
the <Up/Down>button until the display will show “Display Setting”. Press ENTER, the
display will show “Display Setting”.
2Press <Up/Down>, the display will show ”Display Reverse”.
3Press< ENTER>, the display will show ”Display Reverse”.
4The display show “OFF”, Press <Up/Down>, the display will show “ON”.
5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.3.4. Flip Pixel
1. Tap <MODE/ESC> buttonaccess the main menu, Tap the <Up/Down> button until
“Options” is displayed. Press ENTER, the display will show “Options”.
2. Press <Up/Down>, the display will show “Flip Pixel”.
3. Press< ENTER>, the display will show “Flip Pixel”.
4. The display show “OFF”, Press <Up/Down>, the display will show “ON”.,
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.3.5. Temp. C/F
With this function, Display the temperature for Celsius or Fahrenheit.
1Access the main menu.
2Press <Up/Down>, the display will show Temp. C/F.
3Press< ENTER>, the display will show Temp. C/F.
4The display show Fahrenheit,Press <Up/Down>, the display will show “Celsius”.
5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.3.6. Trigger
DMX Value Disp.
With this function you can display the DMX 512 value of each channel. The display
automatically shows the channel with a value changing.
1. Access the main menu.
2. Tap the <Up/Down>button until DMX Value Disp.is displayed.
3. Press ENTER, the display will show DMX Value Disp..

ARCALINE 3 User Manual XM1362-V1.0-NR
16
4. Tap the <Up/Down>buttonchoose each channel.
5. Press ENTER to confirm or press <MODE/ESC> to return to the main menu.
Set To Slave
With this function, you can define the device as slave.
1. Access the main menu.
2. Tap the <Up/Down>button until Set To Slaveis displayed.
3. Press ENTER, the display will show Set To Slave.
4. Tap the <Up/Down>buttonthe display will show “Slave1”, ”Slave2”, ”Slave3”.
5. Press ENTER to confirm or press <MODE/ESC> to return to the main menu.
Auto Program
With this function, you can run the internal program. You can select the desired program
under “Select program”. You can set the number of steps under “Edit program”. You
can edit the individual scenes under “Edit scenes”. With this function, you can run the
individual scenes either automatically, i.e. with the adjusted Step-Time.
1. Access the main menu.
2. Tap the <Up/Down>button until Auto Programis displayed.
3. Press ENTER, the display will show Auto Program.
4. Tap the <Up/Down>buttonthe display will show “Master1”, ” Alone”.
5. Press ENTER to confirm or press <MODE/ESC> to return to the main menu.
9.3.7. ResetDefault
With this function, you can select restore factory set for ON or OFF, the default is OFF.
1Access the main menu.
2Press <Up/Down>, the display will show ResetDefault.
3Press< ENTER>, the display will show ResetDefault.
4The display show OFF,Press <Up/Down>, the display will show “ON”.
5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.4. Info
9.4.1. Time info.
Current Time
With this function, you can display the temporary running time of the device from the last
power on. The display shows “XXXX”, “XXXX” stands for the number of hours. The
counter is resetted after turning the device off.
1. Access the main menu.
2. the display will show Time Information.
3. Press <Up/Down>, the display will show Current Time.
4. Press< ENTER>, the display will show Current Time.
5. The display will show XXXX(Hours) 
6. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
Ttl Life Hrs
With this function, you can display the running time of the device. The display shows
“XXXX”, “XXXX” stands for the number of hours.
1. Access the main menu.
2. Press <Up/Down>, the display will show Ttl Life Hrs.
3. Press< ENTER>, the display will show Ttl Life Hrs.

ARCALINE 3 User Manual XM1362-V1.0-NR
17
4. The display will show XXXX(Hours) 
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
Last Run Hrs
With this function, you can display last the running time of the lamp. The display shows
“XXXX”, “XXXX” stands for the number of hours
1. Access the main menu.
2. Press <Up/Down>, the display will show Last Run Hrs.
3. Press< ENTER>, the display will show Last Run Hrs.
4. The display will show XXXX(Hours) 
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
Timer PIN
With this function, you can display the timer password.
1. Access the main menu.
2. Press <Up/Down>, the display will show Timer PIN.
3. Press< ENTER>, the display will show Timer PIN. The time password is 038.
4. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
Clr Last Run
With this function, you can clear last run time of the fixture. The display shows “ON” or
“OFF”, Press “Enter” to confirm.
1. Access the main menu.
2. Press <Up/Down>, the display will show Clr Last Run.
3. At Timer PINmenu input right password, Press< ENTER>, the display will show
Clr Last Run.
4. The display show OFF,Press <Up/Down>, the display will show ON.
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.4.2. Temp. Info
Head Temp.
With this function you can display the temperature on the display board of the base (near
CMY-filter) in Celsius.
1. Access the main menu.
2. Press <Up/Down>, the display will show Head Temp..
3. Press< ENTER>, the display will show Head Temp..
4. The display show “XXX C/ F”.
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.4.3. Software ver
With this function, you can display the software version of the device.
1. Access the main menu.
2. Press <Up/Down>, the display will show Software ver.
3. Press< ENTER>, the display will show Software ver.
4. The display show “Ver x.x”.
5. Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5. Test

ARCALINE 3 User Manual XM1362-V1.0-NR
18
9.5.1. Test Channel
With this function you can test each channel on its (correct) function.
1Access the main menu.
2Press <Up/Down>, the display will show Test Channel.
3Press< ENTER>, the display will show Test Channel.
4The display show Pan Movingfrist channel, Press <Up/Down>, can choose other
channel.
5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
9.5.2. Manual Ctrl.
With this function, you can adjust the lamp more easily. All effects will be canceled, the shutter
opens and the dimmer intensity will be set to 100 %. With the individual functions, you can
focus the light on a flat surface (wall) and erform the fine lamp adjustment.
1Access the main menu.
2Press <Up/Down>, the display will show Manual Ctrl..
3Press< ENTER>, the display will show Manual Ctrl..
4The display show PAN=XXX.
5Press <ENTER> to confirm or press <MODE/ESC> to return to the main menu.
10. DMX PROTOCOL
DMX channel´s functions and their values (57DMX channels):
Mode/Channel
Value
Function
St
B
a
E
x
Pi


1
1



Red LED -all arrays :
0-255
Red ( 0-Black , 255-100% Red )
2
2



Green LED-all arrays :
0-255
Green ( 0-Black , 255-100% Green )
3
3



Blue LED -all arrays :
0-255
Blue ( 0-Black , 255-100% Blue )
4
4



White LED -all arrays :
0-255
White ( 0-Black , 255-100% White )


10
1

Red LED -array 1 :


0-255
Red ( 0-Black , 255-100% Red )


11
2

Green LED-array 1 :


0-255
Green ( 0-Black , 255-100% Green )


12
3

Blue LED -array 1 :


0-255
Blue ( 0-Black , 255-100% Blue )


13
4

White LED -array 1 :


0-255
White ( 0-Black , 255-100% White )

ARCALINE 3 User Manual XM1362-V1.0-NR
19


14
5

Red LED -array 2 :


0-255
Red ( 0-Black , 255-100% Red )


15
6

Green LED-array 2 :


0-255
Green ( 0-Black , 255-100% Green )


16
7

Blue LED -array 2 :


0-255
Blue ( 0-Black , 255-100% Blue )


17
8

White LED -array 2 :


0-255
White ( 0-Black , 255-100% White )




……


54
4
5

Red LED -array 12 :
0-255
Red ( 0-Black , 255-100% Red )


55
4
6

Green LED-array 12 :
0-255
Green ( 0-Black , 255-100% Green )


56
4
7

Blue LED -array 12 :
0-255
Blue ( 0-Black , 255-100% Blue )


57
4
8

White LED -array 12 :
0-255
White ( 0-Black , 255-100% White )
5
5
1


Shutter, strobe:
0-31
Led trun off
32-63
Led turn on
64-95
Strobe effect slow to fast
96-127
Led turn on
128-159
Pulse-effect in sequences
160-191
Led turn on
192-223
Random strobe effect slow to fast
224-255
Led turn on
6
6
2


Dimmer intensity:
0-255
Intensity 0 to 100%
7

3


Color Macro:
0-7
No function
8-39
from RED to YELLOW
40-71
from YELLOW to GREEN
72-103
from GREEN to CYAN
104-135
from CYAN to BLUE
136-167
from BLUE to MAGENTA
168-199
from MAGENTA to RED
200-231
from RED to WHITE