Azonprinter PRONTO PLUS User manual

Installation and Operation Manual
S/N: Rev.: 1.0

Dear Customer,
Congratulations on deciding to choose anAzonprinter adhesive shaker unit for your DTF
printing activities. You made an excellent choice.
When you need service or technical help, please let us know your purchase invoice
number. This will make it easier to provide you with correct service.
Azonprinter Technical Team
Service Center Link: https://www.azonprinter.com/ticketing-orders/
email: [e-mail]

Rev. 1.0
General
1
1. General
Carefully read the instructions in this manual as they contain important information re-
garding proper, efficient and safe installation, use and maintenance of the unit.
The installation of this unit must be carried out in accordance with the manufacturer’s
instructions.
Switch off the unit in case of failure or malfunction and contact your distributor for
service information.
1.1 Symbols that may be used in this manual
This symbol informs about a situation where a safety risk might be at hand. Given instruc-
tions are mandatory in order to prevent injury.
This symbol informs about the right way to perform in order to prevent bad results, appli-
ance damages or hazardous situations.
This symbol informs about recommendations and hints that help to get the best perform-
ance out of the appliance.

Rev. 1.0
Safety
2
2. Safety
2.1 Safe use of the appliance
For your safety. Do not store or use gasoline or other flammable vapors or liquids in the
vicinity of this or any other appliance.
2.2 Other prohibitions (dangerous procedures)
Using any parts other than genuine Azon approved manufactured parts can void
the warranty.
Improper installation, adjustment, alteration, service or maintenance can cause property
damage or major injury. Read the installation and operating instructions thoroughly be-
fore installing or servicing this equipment.

Rev. 1.0
Functional description
3
3. Functional description
3.1 General
Protno + shakers are:
• Electrically heated
• Heated by infrared tubes
•Have both auto/manual interface
•Mesh belt driven
• Electronically controlled
•Automatically sensor controlled

Rev. 1.0
4
3.2.1 Component Locations
1. Powder box Power Switch
2. Multifunction relay array
3. PLC touch screen
4. Powder recycle drawer
5. Primary Power On Switch
1. Powder box

Rev. 1.0
5
1. Powder blocking strip
(under front top cover)
1. Vented oven lid
2. Vacuum cooling cylinder
3. Cooling fans
4. Motorized take-up reel

Rev. 1.0
6
There are two vacuum cylinders (front and back) to
ensure aligned media feed through the system.
2 zone filtration device includes both charcoal and HEPA filtration.

Rev. 1.0
7
Conveyor belt
Recycled powder drawer

Rev. 1.0
Operations instructions
8
4. Operations instructions
4.1 Before using the unit
Before you begin to use your new shaker oven you must
understand the differences between an automatic shaker and a dialed manual
one. You will produce better re-sults if you understand the technology and
follow the “rules”.
4. 2 The Azon Pronto Plus operates in both automatic and manual modes as selected by the user on
the PLC touch screen.
(1) & (2) The automatic/manual modes control the complete operation of the Azon Pronto Plus
Shaker.
(2)The manual mode allows the user manually control the switches of each device function of the
unit
(3) Heating temperature control (actual)
(4) Preheating temperature controls the front heating plate (actual)
(5) Print linkage engages the front sensor, front vacuum cylinder and shaking device in automatic
mode
(6) Smoke remove switch engages the internal filtration system
(7) Dusting off switch controls the opening and closing of the powder spreader
(8) Shaking off switch controls the on and off functions of the powder shake element
(9) Mesh belt off switch controls the heating of the conveyor belt
(10) Roll on switch controls the functions of the take up reel