Aztech WIPC408HD User manual

V V2 2. .0 0
Aztech WIPC408HD
Wireless N Pan/Tilt High Definition IP Camera

2
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
© Copyright 2013 All rights reser ed. Ver1.0
No part of this document may be reproduced, republished, or retransmitted in any form or by any
means whatsoe er, whether electronically or mechanically, including, but not limited to, by way of
photocopying, recording, information recording, or through retrie al systems without the express
written permission. We reser e the right to re ise this document at any time without the obligation
to notify any person and/or entity. All other company or product names mentioned are used for
identification purposes only and may be trademarks of their respecti e owners.
LIMITATION OF LIABILITY AND DAMAGES
THE PRODUCT AND THE SOFTWARES WITHIN ARE PROVIDED "AS IS," BASIS. THE MANUFACTURER
AND MANUFACTURER’S RESELLERS (COLLECTIVELY REFERRED TO AS “THE SELLERS”) DISCLAIM ALL
WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, OR ANY WARRANTIES ARISING FROM COURSE OF DEALING, COURSE OF PERFORMANCE,
OR USAGE OF TRADE. IN NO EVENT WILL THE SELLERS BE LIABLE FOR DAMAGES OR LOSS,
INCLUDING BUT NOT LIMITED TO DIRECT, INDIRECT, SPECIAL WILLFUL, PUNITIVE, INCIDENTAL,
EXEMPLARY, OR CONSEQUENTIAL, DAMAGES, DAMAGES FOR LOSS OF BUSINESS PROFITS, OR
DAMAGES FOR LOSS OF BUSINESS OF ANY CUSTOMER OR ANY THIRD PARTY ARISING OUT OF THE
USE OR THE INABILITY TO USE THE PRODUCT OR THE SOFTWARES, INCLUDING BUT NOT LIMITED TO
THOSE RESULTING FROM DEFECTS IN THE PRODUCT OR SOFTWARE OR DOCUMENTATION, OR LOSS
OR INACCURACY OF DATA OF ANY KIND, WHETHER BASED ON CONTRACT, TORT OR ANY OTHER
LEGAL THEORY, EVEN IF THE PARTIES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE PRODUCT OR ITS SOFTWARE IS
ASSUMED BY CUSTOMER. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF LIABLITY FOR DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO THE PARTIES.
IN NO EVENT WILL THE SELLERS’ TOTAL CUMULATIVE LIABILITY OF EACH AND EVERY KIND IN
RELATION TO THE PRODUCT OR ITS SOFTWARE EXCEED THE AMOUNT PAID BY CUSTOMER FOR THE
PRODUCT.

3
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
Index
1 INTRODUCTION...........................................................................................................................5
2 FUNCTION AND FEATURES .....................................................................................................6
3 APPEARANCE AND INTERFACE.............................................................................................7
3.1 A PPEARANCE ............................................................................................................................7
3.2 I NTERFACE OF E QUIPMENT .......................................................................................................8
4 NETWORK CONNECTION .........................................................................................................9
4.1 C ONNECTION I NSTRUCTION ......................................................................................................9
4.2 V ISIT I NSTRUCTION ................................................................................................................10
5 VISIT IP CAMERA FROM LAN ................................................................................................10
5.1 S ET IP A DDRESS .....................................................................................................................10
5.2 V ISIT IP C AMERA ...................................................................................................................12
5.2.1 Menu Column.....................................................................................................................13
5.2.2 Video Displaying Area .......................................................................................................13
5.2.3 Browse SD Card.................................................................................................................14
5.2.4 Capture ..............................................................................................................................14
5.2.5 Record................................................................................................................................14
5.2.6 Playback ............................................................................................................................14
5.2.7 The control of Pan/Tilt.......................................................................................................15
5.3 N OTICE ( FOR I NITIAL U SE ) .....................................................................................................15
6 VISIT IP CAMERA FROM WAN ...............................................................................................15
6.1 P ORT F ORWARDING .................................................................................................................15
6.2 DDNS ....................................................................................................................................16
6.2.1 Manufacturer’s Domain Name...........................................................................................17
6.2.2 Third Party Domain Name.................................................................................................17
7 OTHER SETTINGS.....................................................................................................................18
7.1 V IDEO S ETTING P AGE .............................................................................................................18
7.1.1 Video Setting......................................................................................................................18
7.1.2 Audio Setting......................................................................................................................19
7.1.3 Image Setting.....................................................................................................................19
7.2 N ETWORK S ETTING P AGE .......................................................................................................20
7.2.1 Basic Network Setting........................................................................................................20
7.2.2 WIFI Setting.......................................................................................................................20
7.2.3 Remote Access Setting........................................................................................................21
7.3 A LARM S ETTING P AGE ............................................................................................................21
7.3.1 External Alarm Input .........................................................................................................21

4
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
7.3.2 Motion Detection Setting...................................................................................................22
7.3.3 Alarm Mode Setting...........................................................................................................22
7.3.4 Alarm Time Setting / Schedule...........................................................................................23
7.4 A DVANCE S ETTING .................................................................................................................24
7.4.1 User Management..............................................................................................................24
7.4.2 Auto Capture Setting..........................................................................................................25
7.4.3 E-mail Setting ....................................................................................................................26
7.4.4 FTP Setting........................................................................................................................26
7.5 S YSTEM S ETTING P AGE ...........................................................................................................27
7.5.1 Device Information Checking............................................................................................27
7.5.2 Date and Time Setting........................................................................................................28
7.5.3 Default Setting...................................................................................................................28
7.5.4 System Log Checking.........................................................................................................29
8 ADVANCED APPLICATION......................................................................................................29
8.1 A NDROID AND I P HONE M OBILE A PPLICATION S ET U P ............................................................29
8.2 M OBILE P HONE B ROWSING ....................................................................................................30
8.3 U SING O THER W EB B ROWSER TO VISIT THE DEVICE ...............................................................30
8.4 M ULTI D EVICE M ONITOR S YSTEM ..........................................................................................31
9 TECHNICAL PARAMETERS....................................................................................................32
10 SUPPLEMENTARY SECTION..............................................................................................33
10.1 P ORT F ORWARDING R EFERENCES ...........................................................................................33
10.1.1 Aztech DSL1015EW(S) ......................................................................................................34
10.1.2 Aztech DSL1016EN(S2)........................................................Error! Bookmark not defined.
10.1.3 Aztech DSL7000GRV(S) ....................................................................................................35
10.1.4 Aztech DSL7000GR(SME).................................................................................................36
10.1.5 Linksys E1500 Router........................................................................................................37
10.1.6 DLink DVG-N5402SP........................................................................................................38
10.1.7 2wire 2700 HGV-2.............................................................................................................39

5
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
1 Introduction
The IP Camera combines a high quality digital video camera with network connectivity and a
powerful web server to bring clear video to your mobile phone/desktop from anywhere on
your local network or over the Internet.
Your IP Camera package should contain the following items, If any of the listed
items are missing, please contact your reseller from where you purchased the
camera for assistance.
The Package includes:
•IP Camera
•Resource CD Utility with User Manual and MDMS Software
•5V Power Adapter
•Easy Start Guide
•LAN Cable
If you select the device with Wifi function, it has built-in Wifi module and
transmitting antenna in package.

6
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
2 Function and Features
•32-bits RISC processor and special video encoder which can be up to 3M pixels
encoding performance
•Support H.264 Main Prof[email protected] compression format, bit rate is smaller,
and the image is more clear. It is more convenient for transferring through
Internet and save more storage space.
•720P/VGA/QVGA/QQVGA resolution optional. User can change some
specification according to their demands to satisfy his own visual preference.
•Support 3 kinds of video stream, suitable for Local, Internet and Cross-platform
view.
•Built-in microphone, and also support to connect external audio capturing device
(like MIC phone or sound pick-up) to capture the audio. External speaker can play
the voice sent to the live scene, to achieve two-way intercom function. Audio
support G.711 and G.726 types.
•Built-in Pan/Tilt, horizontally 350°, vertically 100°. This equipment is smart and
beautiful, very easy to install and use in many occasions.
•Support IR and color filter change automatically, no any color difference.
•Built-in web server, support video view and parameter settings by browser; use
one port to send all the data, it facilitates network setting.
•Support 802.11b/g /n protocol, can build up wireless monitoring.
•Support mobile phone viewing.
•Support UPNP, port forwarding automatically on the router.
•Support maximum 32G SD card for video and picture storage.
•Motion detection and alarm pin can be connected to external sensors to detect
environmental situation.
•Alarming recording can be stored by email, SD card, and FTP server. External
alarm can be open when detecting unforeseen events. It also sends alarm info to
the alarm server.
•Infrared LED for night vision covers 5m area, to realize 24 hours monitoring.
•Support three level of user authority.
•Support online upgrade.
•Manufacturer attached a label at the bottom of each IP Camera, it include Device
ID, DDNS. When IP Camera is connected to the internet, this URL can be used to
visit the device.
•Manufacturer provides free software, support Multi-view, Long time recording,
video replay etc.
•Support video view by other browsers like as Firefox, Safari etc.

7
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
3 Appearance and Interface
3.1 Appearance
Figure 1
1 – Infrared Lights 6 – Wifi Indicator
2 – Lens 7 – Wireless Antenna
3 – Photovaristor 8 – Shell
4 – Internal Mic 9 – Heat Dissipation Hole
5 – Power Indicator 10 – SD Card Slot
Remarks:
•Power Indicator: it will turn RED if equipment was powered on.
•WIFI Indicator: If there is a WIFI module in the equipment, and there is data
transferring by WIFI, it will begin to blink.

8
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
3.2 Interface of Equipment
Figure 2
1）Power Input Socket: Connect DC adaptor, its output should be 5V power specification.
2）WIFI Antenna Hole: Install the WIFI antenna.
3） RESET Button: Press the RESET button and hold on more than 10 seconds, the
equipment will restart and recover to the factory default settings. The Pan/Tilt will move
around for one circle and finally focus to the center.
4）RJ45 Ethernet Socket: RJ45 Ethernet socket is 10/100M self-adjust. The equipment
can connect to all kinds of network devices, such as hub, router, switch, etc.
5）Audio Input Socket: Audio input socket is designed for connecting external microphone
or line-in audio signal. Please refer to 7.1.2 and select right settings.
6）Audio Output Socket: Audio output socket is for line-out audio player, such as
headphone, speaker, etc.
7）Alarm Output Socket: The alarm output socket is connected with a relay in the IP
camera. IP camera will control the switch to trigger the alarm bell or buzzer to alarm. The
relay is able to control the switch of a alarm whose voltage is no more than 36V, and
current is lower than 2A. Please refer to the Figure 3 for the connection of an external
alarm.
Figure 3
8）Alarming Input Pin: Please refer to the schematic Diagram of Figure 4 for how external
detector collects alarm information.
Output Pins
Alarm power
Alarm
Switch

9
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
Figure 4
The detector should be switched type (always on or always off). If the detector has detected
the smoke or people or animal to enter the area, the detector will switch on or switch off. And
it will send the external alarm signal into the IP camera.
4 Network Connection
Figure 5
IP Camera can be connected with other PC through router, switch or hub to establish a
network. Figure 5 shown connections.
4.1 Connection Instruction
Before visiting the IP Camera, you should firstly connect it to the Network, supply the power
to it, and check if the light of RJ45 Socket is normal to make sure all of the communication
links are fluency. The connection method likes as Figure 5.
1) IP Camera-1 and IP Camera-2 are connected separately to 2 different LANs.
2) And these 2 LANs are already connected to the Internet. In order to get the LANs to be
connected to the Internet, they are required to be equipped with router and to apply for
the communication link from the local Internet Service Provider (ISP) and connect to it by
ADSL or optical fiber, etc.
PIR
PIR Power
Input
pins
Switch

10
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
3) PC-3 is connected to the Internet.
4.2 Visit Instruction
To visit the IP Camera, you should do some settings of IP Camera and Internet besides
getting the communication link fluency.
1) The PC and IP Camera are in the same LAN. If you want to use this PC to visit the IP
Camera, you need to make sure their IP address is at the same segment. Otherwise you
need to do the reset of the IP Camera’s IP address. For example, the IP Camera-1’s IP
address in Figure 5 is 192.168.1.139 (at the segment of 192.168.1), while the PC-1’s IP
address is 192.168.0.175 (at the segment of 192.168.0), then you will be not able to visit
the IP Camera through the PC-1. You need to change the IP Camera-1’s IP address to
192.168.0.139 firstly.
2) The PC and IP Camera are in different LANs, but they are all connected to Internet. For
the IP Camera-1 and PC-2 in Figure 5, if you want to visit IP Camera-1 by PC-2, you
should firstly do the setting as 1) to make sure that you can visit IP Camera-1 through
PC-1 and then do the setting of router-1 (do the port forwarding from the router). The
PC-2’s visit application could be sent through router-1 to IP Camera-1. Normally, PC-2
could only send the information to router-1, if you don’t do the setting of router-1, then
PC-2 could not visit IP Camera-1.
5 Visit IP Camera from LAN
5.1 Set IP Address
The IP addresses of IP Camera and PC should be at the same segment, in Figure 5, the IP
Camera-1 can’t be visited. Run the WIPC408HD Utility in the CD, click Search button, and
then select the IP Camera to reset the IP Camera’s IP address, as the Figure 6.

11
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
Figure 6
If you have the firewall software in your PC, when you run the WIPC408HD Utility,
it may pop up a window to say if you want to block this program or not, then you
should choose not to block.
IP Camera by default use dynamic IP Address and HTTP port 8081. If you don’t
have this software, you could also press down the reset button (Figure 2) to go
back the factory setting. Then you could use this defaulted IP address to visit the
IP Camera.
Setting Instruction:
•Please carefully check the “Local PC information” on the top left corner which lists
the PC configuration. If there are several network adapters in the PC, please select
the one you are using and make sure the IP address of IP Camera is as the same
segment of the PC.
•Change the content of “IP config” on the right to make sure the content is the same
as “Local PC information”.
•If you don’t want to have a fixed IP Address, you could also tick the “Set IP
automatically” to get the IP address from the router automatically (If can’t get IP from
router.
•Put the user name and password into “Authentication” (By default, the user name

12
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
is: admin, password is: admin). Click “Update”. The setting will take effect now.
Select the device in list box, click “Browse” button, it will open the Browser
automatically and pop up a window at the same time which requires to inputting the
user name and password. Then you see the home page of the IP Camera-1, just as
below Figure 7.
Figure 7
5.2 Visit IP Camera
If you are using Internet Explorer or compatible browser to visit it for the first time (use other
browsers, please refer to 8.2), you will be required to install the ActiveX before viewing the
video. As Figure 7, click “Download ActiveX (when first use)”. The dialog just as Figure 8 will
pop up accordingly. Click “Run”, then it will download and install the ActiveX automatically.
Figure 8
After the ActiveX installation, click the “Video View” as Figure 7, then you will enter the video
view home page as below Figure 9.

13
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
Figure 9
5.2.1 Menu Column
There are 2 kinds of menu, one is Main Menu, the other is Sub Menu. The Main Menu lies at
the top of the interface, including View, Media, Network, Alarm, Advanced and System;
SubMenu lies on the right of the interface, and different Main Menus are in line with different
Submenus.
5.2.2 Video Displaying Area
The video displaying area corresponds to the resolution, the higher the resolution is, the
larger the displaying area will be. If motion detection was set, when it has detected any
movements of the certain area, it will show a pane to call user’s attention.
Figure 10 is status column at the bottom of video displaying area.
Figure 10
1）Displaying connection status .
2）If user has clicked the “Record” button in the Figure 9, here will show “Rec”, means the
video is being recorded. If click the “Record” button again, it will stop recording.
3）Zoom Out Button
4）Zoom In Button
5） File Saving Path Setting: User can click it to browse a file saving path to save the
recorded video and snapshots.
6）
Talk-back Button: Click it, and the stereo equipment which was connected to the IP

14
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
Camera will play the achieved audio. Click it again, the speaker will stop playing.
7） Audio Play Button: Click it to play the audio getting from IP Camera, click it again, it will
disable this function.
5.2.3 Browse SD Card
When SD Card inserted, click the submenu, the pop-up page will display the content in SD
Card like the Figure 11.
Figure 11
In above figure, text in [ ] is catalog info, click sub catalog to browse the recorded images and
videos. The images will be displayed when you click them and the videos will be downloaded
and played by the video player in user ’ s computer automatically when click the video.
Note:
•Insert SD Card first before turning ON the IP Camera.
•Proper SD Card Placement – metal contacts facing on top.
5.2.4 Capture
Click the “Capture” button, which could take photos for the current video and store the image
at the present path.
5.2.5 Record
Click “Record” button, which could record the video with audio and store it at the present path.
When recording, there will be an indicated symbol in the status of video display area to show
you it is recording. Click the “Record” button again, and then the record stops.
5.2.6 Playback
Click “Playback” button, it will pop up a player which could play the video stored on your PC
disk.

15
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
Figure 12
, these buttons are for play, stop, the previous recorder, the next
recorder, open the recorder file. Please click the button of “open the recorder file” first,
and select the file you want to play, you can playback the recorder.
5.2.7 The control of Pan/Tilt
At the control area of Pan/Tilt, the user could control the cruise of the Pan/Tilt by the
arrowhead direction (Up/Down/Left/Right/Centre/Stop/Left-right cruise/Up-down cruise).
When your mouse stops on these control buttons, it will guide you what this button mean.
When the IP Camera turns to some position, you can click the “Set” Button, when you
continue to control the Pan/tilt to turn to other position, you could click the “Call” button, the
Pan/Tilt will go back the pre-position.
5.3 Notice (for Initial Use)
Please change the following settings during initial use:
1) Please refer to the content of part 7.4.1 to change the initial passwords of admin, user,
and guest. Their initial passwords are respectively “admin”, “user”, “guest”.
2) Refer to the content of part 7.5.2 to set the System Time.
6 Visit IP Camera from WAN
6.1 Port Forwarding
Follow the “Visit IP Camera from LAN” steps; make sure PC-1 can visit IP Camera-1. In
Figure 5, before the computers in WAN (PC-2, PC-3) can visit the IP Camera-1, must put the
IP Camera -1 into WAN. You can set Port Forwarding on Router-1 to put IP Camera-1 into
WAN.

16
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
Open the Router Setting interface on PC-1. The interfaces for different routers are different,
and the Port Forwarding settings are different, please refer to the Router’s Manual on how to
set. For most routers, “Port Forwarding” option can be found in the Setting / Firewall Interface.
Fill in the IP address and Port of IP Camera-1 into the corresponding blank. Figure 13 is an
example.
Figure 13
Select “status” option and remember the WAN IP address, enter the IP address in browser of
PC-1, if IP Camra-1 can be visited via PC-1, the port forwarding is successful. And PC-2 and
PC-3 can also visit the IP Camera-1.
For further reference, please go to Section 10 of the User Manual to check examples
for Port Forwarding Configuration (Page 33).
WAN IP address is allocated by ISP, please make sure that it is an available WAN
IP address. As WAN IP address is lack, many WAN IP address are available in
limited area. If PC-2 and PC-3 are not in this area, the IP Camera-1 won’t be
visited by them.
If User wants to put several IP Cameras into WAN, every device should set the
Port Forwarding. In order to distinguish these devices, every device should set a
different port. If the port of the device is not 8081, should add the port to IP address
with colon to visit the IP Camera. Example: http://202.96.82.177:81.
6.2 DDNS
In Figure 5, Router-1 get WAN IP address via ADSL, these WAN IP address is always
changing, so, the IP address can’t be confirmed when visit the device in WAN. We need the
dynamic domain name server (DDNS). IP Camera-1 send IP configuration to DDNS every
few times, DDNS can recognize the WAN IP address of the router-1 which connected with IP

17
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
Camera-1. The WAN IP address can be searched on DDNS by domain name. Herein,
domain name substitute the dynamic IP address. If the device can’t be visited by IP address,
this domain name is also unavailable.
6.2.1 Manufacturer’s Domain Name
Device manufacturer has established a DDNS, and allotted a dynamic domain name to every
device, the domain name has been integrated into devices during production. For example,
enter domain name of Figure 14, the browser will connect the device and display the IP
address.
Figure 14
The domain name is realized by forward manner, the domain name will change
into the IP address and port number of the device when visited by domain name.
If the device can be visited by IP address but can’t be visited by manufacturer’s
domain name, please check the DNS info is available or not and make sure the
DNS setting is the same with the DNS setting of PC in LAN.
6.2.2 Third Party Domain Name
User can also use third party DDNS, such as www.3322.org. User should apply a free
domain name from this website and fill the info into the below blanks (Figure 15) and save the
settings. Then the domain name can be used.
Figure 15
The third party domain name is realized by analysis manner, the domain name will
be displayed in the browser all the time when visit camera. If the port is not 80, the
port number should be added to the domain name with colon. Example:
http://ipcam.3322.org:81

18
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
7 Other Settings
7.1 Video Setting Page
7.1.1 Video Setting
Figure 16
Resolution
Use 1280 X 720 Resolution, Bit Rate is 2048 kbps and Frame Rate is up to 30 fps. The higher
the resolutior or quality of the picture, then the bit rate will also be higher and will take more
bandwidth.
User can specify streaming, normally, high bit rate, higher image quality. But the frame rate
need to set according to the bandwidth, when the bandwidth is narrow, if set to high frame
rate, the result will be worse.
User can set Maximum frame rate, when the bandwidth is limited, it is suggested to set to
lower frame rate. Normally, above 15fps the stream is smoothly.
Overlay Options
Through this setting, user can add the Time and Camera Name to the image.

19
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
7.1.2 Audio Setting
Figure 17
Audio Options
User can define value for input and output volume.(100 being the highest value).
First Stream
Audio capture function can be open or close and audio type can be G.711 or G.726. G.711 bit
rate is higher, but more clearly, G.726 compression rate is also high.
7.1.3 Image Setting
Figure 18
1) Color Adjustment: Drag the glide bar showed as above Figure 18, user can adjust the
brightness, saturation and contrast.
2) Image Display Adjustment: There are two options: “Flip” and “Mirror”, Select it for the
image display.
3) IR LED Control and Night vision mode: If you choose “auto/on” mode, IR lights will
be lighted on and shut off by the photo resistance. If you choose “off” mode then IR lights

20
AZTECH
WIPC408HD
IP
CAMERA USER MANUAL v2.0
will be disabld.
7.2 Network Setting Page
7.2.1 Basic Network Setting
Figure 19
1）LAN Setting: The default setting of this equipment is showed as above Figure 19, user
can change it according to your network environment.
2）HTTP Port: The IP address Identifies one IP camera in the network, you can run several
programs on this equipment, and every program will transfer the data through some port,
in fact data is transferred from one port to another. The port setting of this page is asking
the user to choose which port to transfer the data going to the web server.
7.2.2 WIFI Setting