AZURO XP03Hs-Capillary User manual

USER MANUAL

1. Introduction
2. Specifications
3. Installation
4. Initial Startup of the unit
5. Operation
6. Maintenance
INDEX

01
ATTENTION
Thank you for using swimming pool heat pump for your pool heating, it will heat your
pool water and keep the constant temperature when ambient temperature at-5℃ to 40℃
In order to offer qualified, reliable and flexible heat pump unit to our customer, please read
this manual carefully before installing, operating and troubleshooting, then process accordingly.
This manual includes all necessary information
AZURO
● The heat pump unit must be installed by qualified technicians from after-sales
center or authorized distributor.
● Operating and maintaining according to recommended time and frequency on
the manual.
● Use only standard spare parts.
!
1.Introduction

02
2. Specifications
2.1 Swimming Pool Heat Pump Horizontal Design
Models
* Capacity at +25℃
Heat Output 5
Power Consumption
COP
* Capacity at +15℃
Heat Output 3.7
Power Consumption 0.89
COP
*Power Supply
Voltage 220-240
Rated Current 4.1
Advised Fuse 10
WATER DATA
Advised pool volume
0-15
Advised water flux 70
Water pipe in-out spec 50
*General Data
Compressor Rotary
Air flow Horizontal
*Condenser Titanium in PVC
Noise level(10m) 35
Noise level(1 m) 46
Water Pressure 12
Refrigerant 0.8
*Dimension & Weight
Net Dimension 750*325*470
Net Weight
Packing Dimension
Gross Weight
KW
KW
KW
KW
V
A
A
m³
L/min
mm
dB(A)
dB(A)
Kpa
kg
mm
kg
mm
kg
37
42
855*345*530
0.9
5.5
4.15
8.7
6.45
1.43
220-240
6.7
20
25-35
100
50
Rotary
Horizontal
36
47
15
1.1
930*360*550
50
56
1060*380*600
1.45
6
4.5
XP05Hs-EEV
12
9.0
1.95
220-240
9.3
20
35-55
140
50
Rotary
Horizontal
37
48
15
1.3
1000*360*620
65
72
1060*380*660
2.0
6
4.6
12
9.0
1.95
220-240
9.3
20
35-55
140
50
Rotary
Horizontal
37
48
15
1.3
1000*360*620
65
72
1060*380*660
2.0
6
4.6
5
3.7
0.89
220-240
4.1
10
0-15
70
50
Rotary
Horizontal
35
46
12
0.8
750*325*470
37
42
855*345*530
0.9
5.5
4.15
XP05Hs-Capillary
XP09Hs-EEV
8.7
6.45
1.43
220-240
6.7
20
25-35
100
50
Rotary
Horizontal
36
47
15
1.1
930*360*550
50
56
1060*380*600
1.45
6
4.5
XP09Hs-Capillary XP12Hs-Capillary
XP12Hs-EEV
3.5
2.56
0.61
220-240
3.2
10
0-15
70
50
Rotary
Horizontal
35
46
12
0.6
750*325*470
36
38
855*345*530
0.70
5
4
XP03Hs-Capillary

03
NOTE: The factory only provides the heat pump unit. The other items in the illustration are necessary
spare parts for the water system which are provided by users or installers.
3. Installation
3.1 Installation illustration
(1) The heat pump unit must be installed by professional technicians .otherwise unit may
be damaged or body injured, even dead
(2) The unit is designed for outdoor location with good ventilation. Recirculation of cold
discharge air back into evaporator coil will greatly reduce heating capacity and
efficiency of the unit, which will void the compressor warranty.
(3) The unit can be installed almost anywhere in the outdoors.To get a good performance,
it needs to meet the three factors :
a) Good ventilation
b) Stable and reliable power supply
c) Recycled water system
The difference from gas water heater, it should not bring environmental pollution or
have the installing problems in-windy areas.
ATTENTION:
Please follow these steps when operating the first time :
1.Open valve and charge water
2.Make sure that the pump and the water-in pipe have been filled with water
3.Close the valve and start the unit
!
3.2 Installation

04
(4) The unit should not be installed in a limited air ventilation area ,or placed in a bush
where it will block the air inlet，These location deny the unit of a continuous source of fresh
air .When seasons changing ,it may stick leaves on the evaporator coil ,thereby reducing
its efficiency and impact of its service life .
(5) For indoor installation, please consult more instruction from technicians.
(6) When install a bypass, it should be not exceed 30% of nominal flow rate
(7 Must make Water level higher than the circulation pump location.
(8) Below picture show the minimum required distance on each side of pool heat pump unit.
Air inlet
Air outlet
2500mm
( ) Typically, the pool heat pump unit should be installed aside the pools, less than 7.5
meters distance. If it is installed farther away, the pipeline system will cause greater
heat loss. The most of pipeline are installed under ground ,although the pipeline
system has to do thermal insulation ,but tunnels and the soil around will still occur heat
exchange ,for example,each 30 meters ( 15 meters t oand from the pump=30 meters
total),unless the ground is wet or the water table is high.A very rough estimate of heat
loss per 30 meters is 0.6KW per hour (2000BTU) for every 5℃ surrounding the pipe,
which translates to about 3% to 5% increase in run time.
(10) To get the best heat exchange of heat pump unit, it should be matched the normal rate
of water flow recommended in specification sheet.
(11) It is required to increase the discharge pipe to prevent freezing in cold season, to put
“T” fitting and ball valve to facilitate changing the water in winter or emptying the water
out of system to prevent freezing when HP stop operating at the ambient temperature
below zero ,otherwise the unit may be damaged.
9

05
Pressure-type Chlorinator or Brominator
P-trap
Filter Chlorinator
Check-valve
Water pump
Check-valve
3.3 's instruction to your system is also critical
to the heater's life.
The location of chemical
If an automatic chlorinator or brominates is used, it must be located downstream of the
heater.A trap must be installed between the chlorinator and the heater to prevent chlorine
return into the heat pump. (See below pictures)
Note: Please make sure the water pump is running in circulation with adequate rate of
water flow.
Startup Procedure after Installation is completed, and please follow these steps:
(1) Turn on your filter pump ,check water leaks and verify flow of swimming pool
(2) Turn on the electrical power supply to the unit, then press the key ON/OFF of wire
controller, it should start in several seconds.
(3) After running a few minutes make sure the air ventilation from the side (top) of the
unit is cooler ( Between 5℃ and 10℃)
(4) When turn off the filter pump , the unit should also turn off automatically , if not, then
adjust the flow switch
(5) Allow the unit and pool pump to run 24 hours per day until the water reaches the
desired temperature .When the temperature reaches the setting value ,the HP unit
will shut down ,when the pool temperature drops more than 1℃, pleaserestart (as
long as HP unit is running )
Water Flow Switch:
It is equipped with a flow switch for protecting the HP unit running with adequate water
flow rate .It will turn on when the pool pump runs and shut it off when the pump shuts off.
If the pool water level higher than 1 m above or below the heat pump's automatic
adjustment knob, your dealer may need to adjust its initial startup.
4. Initial Startup of the unit
In-line Chlorinator or Brominator
P-trap
Check-valve
Chlorinator
Filter
Water pump

Time Delay:
HP unit should be equipped with a 3-minute built-in solid-state re-start delay protection.
Time delay control is an integral part of the circuit control, it can eliminate restart cycling
and contactor chatter.
The time delay will automatically restart the HP unit approximately 3 minutes after each
control circuit interruption .Even a brief power interruption will activate the solid state 3
minute restart delay and prevent the unit from the starting until the 3 minutes countdown
is completed.
10
HEAT
LED display
Press to
adjust the water
temperature
Press to set Timer on
Press to set im off T er
Press to set the Time
Press to turn
on and turn off the nit U
Operation mode
instruction
5. Operation
5.1 The functions of LED wire controller
5.2 How to set operation parameter (LED display show real time till HP unit is
power off. )
(1) Long press " " 5 seconds to enter operating parameter setting interface.
(2) Under parameter setting, Press and hold for 5 seconds to enter operating
parameter setting interface
(3) Under parameter setting, Press " "again to start setting parameters from 0 to A#,
(see operation parameter table).
(4) Leave it 8 seconds, LED will display water in temperature (under running) or time (until
stops).
(5) Under current mode, press or to modify the water setting temperature whenever it
is ON/OFF status.
06

07
10 10
MODE
HEAT
HEAT
10
10
MODE
HEAT
10
MODE
HEAT
10
MODE
HEAT
10
MODE
HEAT
Parameter 3
Terms of Entry defrosting
function (-30 to 0 ,
default setting -7℃)
℃ ℃
Parameter 2
Total working time of
compressor after frosting
(30-90MIN ,default
setting : 40MIN)
Parameter 0
To set the entering water
temp. under cooling mode
(8-35℃,default setting:
28℃)
Parameter 1
To set the entering water
temp. under heating mode
(15-35℃, default
setting:28℃)
Parameter 4
Terms of Exit defrosting
function (2 to 30 ,
default setting 13℃)
℃
Parameter 5
Time of Exit defrosting (1 to
12MIN, default setting 8MIN)

08
HEAT
10
HEAT
10
Parameter 9
Cooling target for superheat
,default setting -2℃(-15℃-15℃ )
Parameter A
Manual adjustment steps of
electronic expansion valve
(18-94 ).defaulting setting :
70(*5)
10
HEAT
10
HEAT
Parameter 6
Mode : 0 Cool 1 Heat and Cool
2 Heat and cool + auxiliary elec.
Heating 3 Heat
default setting : 3 Heat
Note: Parameter 7 is only applied
for HP units with Electronic
expansion valve .
10
HEAT
Parameter 7
Mode selection of Electronic
expansion valve ( 0 to 1),
default setting 1 (auto)
Parameter 8
Heating target for superheat
(-15 -15 ) default setting :3℃℃ ℃
10
HEAT
10
HEAT
Parameter n
Refrigerant compressor
output protection
(range:85 to 110 ,
default :100 )
℃ ℃
℃
Parameter O
Low ambient temperature
protection
(range:-10 -10
default 7 )
℃ ℃,
: ℃

09
(1) Long press“ ”5 seconds to enter operating parameter setting interface.
(2) .You can
check water -in/water-out /Condenser/ambient temperature.
(3) Mode can be changed while running.
(4) When the unit is switched off, current time is displayed.
Time setting:
Press to set the time, and press or to adjust the time
After pressed the again to store the new data.
When setting the time, and can not work.
TIMER ON SETTING
Press to set the time for HP start to run ,and press or to adjust starting time.then,
to press again to store the new data.
When lights, Press to cancel the timer setting.
TIME OFF SETTING
Press to set the time for HP stop running, press or to adjust the time of stop
running. then, press againto store the new data.
When lights, press to cancel the timer setting.
Press and hold for 5 seconds to enter operating parameter setting interface
10
1
1
0
0
ATTENTION:
HP running parameters must be checked after installation and before first used.
When HP is running, LED displays water inlet temperature
When HP is stopping, LED wire controller displays the actual time.
When HP running, the running mode ( cooling or heating) and water temp could be changed.
Other parameters only changeable when HP stopping.
!
5.4 RUNNING DATA SETTING

10
Remarks :
(1) When HP stop running in 30 seconds ,water pump will shut off automatically .
(2) LED wire controller can operate the water pump after connected additional cable to the
pump device in the position of “PUMP” terminal accurately .
(3) It is necessary to put an extra 3-phase transfer device for 3 phase water pump
Parameter Meaning Range Default Remarks
0To set the entering water temp. under cooling mode 8-35℃28℃Adjustable
1To set the entering water temp. under heating mode 15-35℃28℃Adjustable
Entry into defrosting time period
230-90MIN 40MIN
3
4
5
6
7
8
9
A
b
C
d
E
F
G
H
Terms of Entry defrosting function -30 to 0℃ ℃ -7℃
Terms of Exit defrosting function 2 to 30℃20℃
Time of Exit defrosting 1 to 12MIN 8MIN
Mode : 0 Cool 1 Heat and Cool 2 Heat and cool
+ auxiliary elec. heating 3 Heat 0-3 3 ( Heat)
Mode selection of Electronic expansion valve 0-1 1 (auto)
Superheat for heating target -15℃-15℃3℃
Superheat for cooling target -15℃-15℃10℃
Manual adjustment steps of electronic expansion valve 18-94 70
Inlet water temperature -9-99℃Exact testing by value
-9-130℃
Condenser temperature under heating mode
Gas return temperature
Ambient temperature
Condenser temperature under modeCooling
Actual steps of electronic expansion valve N*5
-9-99℃
-9-99℃
-9-99℃
–
Exact testing by value
Exact testing by value
Exact testing by value
Exact testing by value
Exact testing by value
–
n85℃-110℃100℃
o-10℃-10℃7℃
Low ambient temperature protection
Refrigerant compressor output temperature protection
Refrigerant compressor output temperature

11
(1) You should check the water supply system regularly to avoid the air entering the system and
occurrence of low water flow, because it would reduce the performance and reliability of HP unit.
(2) Clean your pools and filtration system regularly to avoid the damage of the unit as a result
of the dirty of clogged filter.
(3) , ,
(4)
(5) Check power cable connection ,if heat pump start to operate abnormally ,you should turn it
off and contact with qualified technicians.
(6) You should discharge the water from water pump and other water system, prevent from
the freezing damage in inter seasons.
(7) You should discharge the water from bottom of water pump if HP unit will stop running for a
long time. In another way, you should check the units thoroughly and fill the system with water
fully before the unit start to run again.
Keep the HP unit dry clean well-ventilated and always clean side of the heat exchanger
which can maintain a good heat exchange and energy saving.
Only a qualified service technician is allowed to operate pressure of the refrigeration
system.
s
to
w
6. Maintenance