B meters IWM-MB3 User manual

Quick user guide_v1.0
IWM-MB3
Modulo MBUS a filo per contatori B METERS
Il modulo IWM-MB3 è un dispositivo che consente di trasmettere tramite protocollo MBUS
i dati di lettura rilevati dai contatori d’acqua serie GMDM-I, GMB-I, GMB-RP-I e CPR-M3-I
prodotti da B METERS.
Il dispositivo deve essere configurato tramite il software di configurazione BMBUS e un
master MBUS. Questo permette di impostare l’indirizzo primario, le diverse opzioni di
funzionamento e consente di effettuare le letture dei dispositivi.
Per il download del software, collegarsi al seguente link https://www.bmeters.com/wp-
content/uploads/2021/09/setupBMBusP-v1.1.2.137.zip. Si rimanda al manuale del software
per una descrizione dettagliata delle funzioni e delle opzioni di configurazione disponibili.
Il periodo di garanzia è posto a 24 (ventiquattro) mesi dalla data di spedizione del
materiale. Tale garanzia è limitata a vizi di progettazione, materiali e lavorazione
evidenziatisi in condizioni di normale utilizzo e manutenzione. Questa garanzia è valida
ed eseguibile nel paese in cui è stato acquistato il prodotto. Nel caso dell’Unione Europea,
la garanzia è valida per tutti i paesi della Comunità.
Per ottenere il servizio di garanzia, è richiesto di rispettare le seguenti clausole:
L’installazione del modulo IWM-MB3 è prevista esclusivamente sui contatori serie
GMDM-I, GMB-I, GMB-RP-I e CPR-M3-I.
Installare il modulo sul contatore, come mostrato in fase [1]. E’ assolutamente necessario
far combaciare gli agganci del contatore con quelli del modulo. Con una mano tenere
fermo il contatore, con l’altra mano spingere dunque delicatamente il modulo, fase [2]
e ruotarlo in senso antiorario per fissarlo al contatore, fase [3].
Collegare i cavi al bus rispettando le tipologie di connessione consentite, per ulteriori
informazioni sulle tipologie di connessione ammesse è possibile fare riferimento al
seguente link:
.
Il dispositivo presenta due conduttori di colore bianco e marrone, non vi è necessità
di rispettare polarità.
Il dispositivo deve essere configurato con apposito software BMBUS* per il suo
funzionamento. L’installatore ha il compito di verificare il corretto invio dei dati durante
l’installazione. Si consiglia di configurare il modulo tramite l’uso del software BMBUS e
di un master MBUS*. Prima di procedere con la parametrizzazione, installare il modulo
sul contatore, come mostrato in figura e collegarlo al bus. Procedere con la ricerca tramite
indirizzo secondario del modulo e con la configurazione desiderata (assegnazione del
conteggio iniziale presente nel contatore al momento dell’installazione del modulo e
assegnazione dell’indirizzo primario se richiesto).
Per una corretta installazione del modulo sul contatore, è necessario inserire la vite
di fissaggio ed applicare il sigillo adesivo nel punto indicato in figura fase [4].
Nel caso in cui il prodotto dovesse richiedere assistenza tecnica, contattare il Vs. fornitore
oppure il servizio di supporto After-Sales B METERS all’indirizzo ticket@bmeters.com.
Con la presente B METERS dichiara che questo IWM-MB3 è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla Direttiva 2014/30/EU.
La dichiarazione completa può essere scaricata dal sito web ufficiale www.bmeters.com.
B METERS s.r.l.
Via Friuli 3
Italia
Web: www.bmeters.com
*Le batterie non sono sostituibili. NON TENTARE SOSTITUZIONI di alcun tipo.
Eventuali tentativi comporteranno la perdita della garanzia, inoltre potrebbero
danneggiare irrimediabilmente il dispositivo.
*E’ possibile configurare il dispositivo anche utilizzando custom string, software e/o
Contattare ticket@bmeters.com per maggiori dettagli.
** Massimo 24 ore di sommersione continua ad 1 m di profondità.
Contenuto della confezione
Dati tecnici
Installazione
Messa in servizio
Assistenza sui prodotti
Info e contatti
Dichiarazione di Conformità
Descrizione prodotto
Garanzia
Precauzioni di sicurezza
Modulo IWM-MB3
Vite di fissaggio
Adesivo anti-manomissione
Guida installazione
Durante il processo di installazione, maneggiare il dispositivo con cura, non
schiacciare, non esporre a cariche elettrostatiche che potrebbero danneggiare
irrimediabilmente il dispositivo, non installare vicino a sorgenti di calore (come
radiatori, condizionatori, convettori etc.).
Il dispositivo non contiene materiale pericoloso, in conformità alla direttiva europea
è necessario smaltire il prodotto come specificato nella direttiva RAEE per i paesi
dell’Unione, o comunque sempre in ottemperanza delle leggi e norme locali. Non
bruciare, non sottoporre ad alte temperature.
Il modulo IWM-MB3 funziona in modo affidabile nelle condizioni ambientali
specificate in questo manuale. Eventuali interventi non autorizzati e/o cambiamenti
di uso e funzionamento possono provocare malfunzionamenti o il danneggiamento
del prodotto.
1. I prodotti devono essere consegnati per la riparazione a spese del Cliente.
2. La garanzia del prodotto sarà soggetta alla mostra di un documento fiscale (fattura
di vendita), che attesta la data di acquisto del prodotto.
3. La riparazione non influisce sulla data originale della scadenza della garanzia e non
comporta il rinnovo o la proroga.
4. Se al momento della riparazione il prodotto non presenta alcun difetto, verrà
addebitato il costo dell’analisi tecnica.
La garanzia è nulla se il guasto è dovuto a: impatti, cadute, abuso del prodotto,
utilizzo di batterie non originali, incidenti, alterazioni del prodotto, sostituzione/
distacco delle guarnizioni e/o manomissioni del prodotto. Allo stesso modo, non vi
è copertura anche per i danni causati durante il trasporto se le confezioni utilizzate
non sono idonee.
6. La garanzia non copre la batteria del prodotto.
7. La garanzia non copre l’incapacità di utilizzare il prodotto, altrimenti causano danni
accidentali o consequenziali o altre spese sostenute dall’acquirente.
8. La garanzia non copre eventuali danni causati da un utilizzo diverso da quello indicato
nel presente manuale.
Livello protezione: IP68**
Peso: 120g

Quick user guide_v1.0
IWM-MB3
Wired MBUS module for B METERS water meters
The IWM-MB3 module is a device that allows to transmit through the MBUS protocol
the reading data detected by the GMDM-I, GMB-I, GMB-RP-I and CPR-M3-I series
water meters produced by B METERS. The device must be configured using the BMBUS
configuration software and an MBUS master. This allows you to set the primary address,
the different operating options and allows you to read the devices. To download
the software, connect to the following link https://www.bmeters.com/wp-content/
uploads/2021/09/setupBMBusP-v1.1.2.137.zip. Please refer to the software manual for a
detailed description of the available functions and configuration options.
The warranty period is set at 24 (twenty-four) months from the date of the shipping of
the material. Warranty is against defects in materials or workmanship when the product is
properly used and maintained in normal efficiency. This Warranty is valid and enforceable
in the country where the product was purchased. In the event that the product has been
purchased in a country of the European Union, the warranty is still valid in all countries of
the Community.
To obtain warranty service, it is requested to comply with the following clauses:
The IWM-MB3 module can be installed exclusively on the GMDM-I, GMB-I, GMB-RP-I and
CPR-M3-I series meters.
Install the module on the meter, as shown on step [1]. It is absolutely necessary to match
the counter hooks with those of the module. With one hand, hold the meter, with the
other hand, gently push the module, step [2] and turn it counter-clockwise to fix it to
the counter, step [3]. Connect the cables to the bus respecting the types of connection
allowed. For further information on the types of connections allowed, please refer to
the following link:
.
The device has two conductors white and brown, there is no need to respect polarity.
The device must be configured with the appropriate BMBUS * software for its operation.
The installer has the task of verifying the correct transmission of data during the
installation. We recommend that you configure the module using the BMBUS software and
an MBUS * master. Before proceeding with the parameterization, install the module on the
meter, as shown in the figure and connect it to the bus. Proceed with the search via the
module’s secondary address and with the desired configuration (assignment of the initial
count present in the meter when installing the module, and assignment of the primary
address if required).
For a correct installation of the module on the meter, it is necessary to insert the fixing
screw and apply the adhesive seal at the point indicated in the figure step [4].
If the product needs to be sent to the technical assistance, contact your dealer or contact
the B METERS After sales service at [email protected].
B METERS
requirements and other relevant provisions of Directive 2014/30/EU.
The complete declaration can be downloaded from the official website www.bmeters.com.
*Batteries are not replaceable, DO NOT ATTEMPT TO REPLACE THEM.
Any attempt will void the warranty, moreover will irreversibly damage the device.
*The device can also be configured using custom string, software and/or third-party
** Maximum 24 hours of continuous submersion at 1 m depth.
Package Content
Technical data
Installation
Commissioning
Support on the products
Info & contacts
Declaration of Conformity
Product description
Warranty
Safety
IWM-MB3 module
Mounting screw
Anti-tampering sticker
Installation guide
During the installation process, handle the device with care, don’t crush, don’t bent,
don’t expose to electrostatic discharges which could damage permanently the
device, do not install close to heat sources (radiators, conditioners, convectors etc.).
The module doesn’t contain hazardous materials in accordance with European
specific disposal on the end of its lifetime. Recycling is mandatory or recommended
following the Directive RAEE inside European Union region, or anyway dispose
in accordance with local laws and regulations. Do not burn, or undergo to high
temperatures.
The IWM-MB3 works reliably in the environmental conditions specified in this manual.
Any unauthorized intervention and/or modification may cause malfunctions or total
damaging of the product.
1. Products must be delivered for repair at the expense of the customer.
2. The product warranty will be subject to the exhibition of a tax document (receipt,
receipt or bill of sale), which attests to the date of purchase of the product.
3. The repair will not affect the original date of expiration of the warranty and will not
involve the renewal or extension thereof.
4. If at the time of the repair, the product has not any defect, it will be charged the costs
of the technical analysis.
The warranty is void if the failure was due to: impacts, falls, misuse or abuse of the
product, use of non-original batteries, accidents, product alteration, replacement/
detachment of seals and/or product tampering. The same also does not cover
damage caused during transport if packages used are unsuitable.
6. The warranty is not covering the battery of the product.
7. The warranty does not cover the inability to use the product, other costs incidental or
consequential damages or other expenses incurred by the purchaser.
8. The warranty doesn’t cover damage to the product caused by usage in any other way
than described in this manual.
Protection level: IP68**
Weight: 120g
B METERS s.r.l.
Via Friuli 3
Italia
Web: www.bmeters.com
Table of contents
Languages:
Other B meters Control Unit manuals

B meters
B meters RFM-TX1.1 User manual

B meters
B meters IWM-LR3 Instruction manual

B meters
B meters RFM-MB1 Instruction manual

B meters
B meters MB-PULSE4 Instruction manual

B meters
B meters IWM-PL4 User manual

B meters
B meters IWM-PL4 Instruction manual

B meters
B meters IWM-TX5 User manual

B meters
B meters IWM-MB4 User manual

B meters
B meters RFM-TX2 User manual

B meters
B meters IWM-LR4 User manual