B-Tech BT8500 Instruction Manual

UNIVERSAL INTERFACE KIT
FOR MOUNTING LARGE FLAT PANEL DISPLAYS
ASSEMBLY AND INSTALLATION
BT8500
BT8500
IMPORTANT :
DUE TO THE HEAVY WEIGHT OF PLASMA SCREENS, B-TECH RECOMMENDS THAT A PROFESSIONAL INSTALLER IS USED WHEN MOUNTING THIS BRACKET AND PLASMA.
B-TECH INTERNATIONAL LTD., ITS DISTRIBUTORS AND DEALERS ARE NOT RESPONSIBLE FOR DAMAGE OR INJURY CAUSED BY IMPROPER INSTALLATION.
This pack contains 1 Universal Interface KIt designed for use with any of the following brackets:
BT8000, BT8001, BT8002, BT8003, BT8004, BT8016, BT8017
Please keep these instructions for future reference.
PARTS LIST
1/4" Washers x 4M5 x 12mm Screws x 4
Interface Plate x 1
Adaptor Plates
x 2
B-Tech International Limited, Croydon, CR0 9UG, UK
www.b-tech-int.com
copyright 2004
Plasma Fixing Kit
SPACER Ø12 x 5.5 x L:12
SPACER Ø14 x 6.5 x L:9.5
SPACER Ø13 x 8.5 x L:13
SPACER Ø20 x 13.5 x L:13
M8 x 15mm Screw
M8 x 25 mm Screw
M8 x 40mm Screw
M6 x 12mm Screw
M5 x 12mm Screw
M5 x 20mm Screw
M5 x 30mm Screw
M4 x 10mm Screw
WASHER Ø5/16 x Ø20 x T:2
WASHER Ø1/4 x Ø16 x T:1.6
WASHER Ø5 x Ø12 x T:1.0
6
4
4
4
6
4
4
6
8
6
4
8
8
8
8
DESCRIPTION QTY
M8 x 50mm Screw 4

3
Place the Interface Plate on back so that the Adaptor Plates are over the holes on the back of the plasma, making sure that the directional
arrow is facing up (same as the plasma screen). Spacers must always be used where the mounting holes are recessed. On some plasma
casings, there are various high and low points. Using the spacers provided, ensure that the Interface Plate should not press against the
casing.
From the comprehensive fixing kit supplied, choose the applicable
bolts according to the mounting holes on the casing (eg M4, M5 or
M6).
Spacers must always be used where the mounting holes are
recessed. On some plasma casings, there are various high and low
points. Using the spacers provided, ensure that the Interface Plate
does not press against the casing.
IMPORTANT : Always tighten the bolts by hand first to ensure that
they are the correct thread size. Using incorrect screws can cause
permanent damage to the plasma screen.
4
5
Once the Adaptor Plates are secured to the plasma casing, the adaptor
plates can then be bolted to the interface plate.
Once the bracket is secure, it is now safe to mount on the wall with the
wall bracket (BT8000, BT8001, BT8002 or BT8003), on the trolley
(BT8004) or on one of the ceiling adaptors (BT8016 or BT8017).
Simply slide the plasma screen onto the bracket so it hooks onto the
slots provided.
Use the 2 Security Screws provided with the Security Key to lock the
plasma to the wall
Alignment of Interface Kit
Mounting Interface Kit to Plasma
Complete the Mounting
ASSEMBLY AND INSTALLATION
12
Slide the Adaptor Plates onto the Interface Plate as above (this part may
come pre-assembled). The Adaptor Plates may be fitted either way
round.
Do not insert bolts and tighten until Step 5.
Place the Plasma Screen down on the floor, table or other suitable
surface (take care not to damage the screen).
Note where the mounting holes are located on the back of the
casing. On most plasma's, there are two sets of vertical parallel
holes.
Assemble the Interface Kit
Locate Mounting Holes