B810 digicom 8D5896 User manual

8D5896 _ 4G Lift Dialer
8D5896B _ 4G Lift Dialer Box
User’s Guide
rev. 1.0 10/2020
REMOTE ALARM SYSTEM
ITALIANOENGLISH

TM
4G Lift Dialer & 4G Lift Dialer Box Preface
I
4G Lift Dialer & 4G Lift Dialer Box Preface
INDEX
PREFACE .........................................................................................................................................................II
BACKUP BATTERY..........................................................................................................................................II
SIMPLIFIED UE DECLARATION OF CONFORMITY ...................................................................................... II
ASSISTANCE AND CONTACTS ......................................................................................................................II
SAFETY WARNINGS ...................................................................................................................................... III
1. INTRODUCTION............................................................................................................................................1.1
1.1. TECHNICAL FEATURES ......................................................................................................................1.1
1.2. SYSTEM DESCRIPTION AND PACKAGE CONTENT ......................................................................... 1.2
2. INSTALLATION .............................................................................................................................................2.1
2.1. SUGGESTIONS FOR SECURITY ........................................................................................................2.1
2.2. INSTALLATION ARCHITECTURES ...................................................................................................... 2.1
2.3. TESTS DURING THE INSTALLATION.................................................................................................. 2.6
2.4. BEFORE POWERING LIFT DIALER ON .............................................................................................. 2.7
2.5. VOICE BOX CONNECTION.................................................................................................................. 2.8
2.6. 4G LIFT DIALER PINOUT..................................................................................................................... 2.9
2.7. LIFT DIALER TOPOGRAPHY ...............................................................................................................2.9
2.8. VOICE BOX - CAR PINOUT (CODE 8D5804) .................................................................................... 2.10
2.9. VOICE BOX - CAR TOPOGRAPHY (CODE 8D5804) ........................................................................ 2.10
2.10.VOICE BOX - TOP / PIT PINOUT (CODE 8D5780)............................................................................ 2.11
2.11. VOICE BOX - TOP / PIT TOPOGRAPHY (CODE 8D5780) ................................................................ 2.11
2.12.VOICE BOX BUTTON PINOUT (CODE 8D5810) ............................................................................... 2.12
2.13.VOICE BOX BUTTON TOPOGRAPHY (CODE 8D5810) ................................................................... 2.12
2.14.LIFT DIALER: LED INDICATORS .......................................................................................................2.13
2.15.VOICE BOX: LED INDICATORS......................................................................................................... 2.13
2.16.BACKUP BATTERY.............................................................................................................................2.14
2.17.RESET BUTTON.................................................................................................................................2.14
3. CONFIGURATION ......................................................................................................................................... 3.1
3.1. CONFIGURATION VIA LOCAL PHONE................................................................................................ 3.1
3.2. CONFIGURATION VIA REMOTE PHONE............................................................................................ 3.1
3.3. CONFIGURATION VIA SMS ................................................................................................................. 3.2
3.4. CONFIGURATION TABLE..................................................................................................................... 3.2
3.5. CONFIGURATION EXAMPLES ............................................................................................................3.8
3.6. MULTI-COMMANDS VIA SINGLE SMS................................................................................................ 3.8
3.7. RECORDING THE ALARM MESSAGE (COMMAND 40#) ................................................................... 3.8
3.8. PLAYING THE ALARM MESSAGE (COMMAND 41#).......................................................................... 3.8
3.9. MANAGING THE ALARM CALL............................................................................................................3.9
3.10.RESETTING THE ALARM (COMMAND 19) ......................................................................................... 3.9
3.11. RESTORING THE FACTORY CONFIGURATION (COMMAND *99#).................................................. 3.9
3.12.RESTORING THE COMPLETE FACTORY CONFIGURATION (COMMAND *9900#)......................... 3.9
3.13.CHANGING THE LANGUAGE (COMMAND 45*XX#) ........................................................................ 3.10
3.14.ADJUSTING SPEAKER VOLUME AND MICROPHONE GAIN .......................................................... 3.10
3.15.ACTIVATION OF SPEAKERPHONE IN CAR IN INCOMING CALLS ................................................. 3.10
3.16.ACTIVATING THE INTERCOM FUNCTION (COMMAND *1)............................................................. 3.11
3.17.RELAY 1 AND 2: MANAGEMENT FOR GATE OPENING (COMMANDS 81# AND 82#) ................... 3.11
3.18.RELAY1: BELL MANAGEMENT (COMMAND 84T#) .......................................................................... 3.12
3.19.RELAYS 1: ACTIVATION MANAGED BY SENSOR CONNECTED TO THE VOICE BOX ................. 3.12
3.20.RELAY 2: GSM NETWORK ABSENT (COMMAND 861#).................................................................. 3.12
3.21.RELAY 1 AND RELAY 2: SENT ALARM AND RECEIVED ALARM (COMMAND 851#) ..................... 3.13
3.22.RELAY 2: ITALIAN LAW 13 MANAGEMENT (COMMAND 831#) ....................................................... 3.13
3.23.ALARM FILTERING............................................................................................................................. 3.13

II
4G Lift Dialer & 4G Lift Dialer Box Preface
III
4G Lift Dialer & 4G Lift Dialer Box Preface
All rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or trasmitted in any form or by any means, electronic, otherwise,
without the prior written permission of Digicom S.r.l.The contents of this booklet may be modified without notice. Every possible care has been taken in testing and
putting together all the documentation contained in this booklet, however Digicom can not take any responsability brought by the use of this booklet.
PREFACE
In order to guarantee your safety and a correct functioning, be sure to follow these safety warnings. The whole set (with cables
included) must be installed in a place lacking of or distant from:
• Dust, humidity, high temperatures and direct exposure to sunlight.
• Heat irradiating objects, which may damage your device or cause any other problem.
• Objects producing a high electromagnetic field (Hi-Fi speakers, etc.).
• Corrosive liquids or chemical substances.
ENVIRONMENTAL CONDITIONS
Environment temperature: from -10 °C to +55 °C Relative humidity: from 20 to 80 % n.c.
Any sudden change in temperature and humidity must be avoided.
Use a soft dry cloth and avoid any solvents or abrasive materials.
Caution against shocks or vibrations.
BACKUP BATTERY
WARNING: this device can be equipped with a Li-ion Polymer backup battery.
This battery may get burnt, explode or cause serious burnings. DO NOT disassemble, weld, burn or throw the battery into water.
Keep out of children. Replace only with a same model battery and reserve the operation only to qualified staff. The use of a different
battery may cause fire hazard or explosions. Italian laws consider batteries as dangerous urban waste that must be disposed
according to the law provisions in force (Italian DPR 915/82 and local provisions).
The backup battery is excluded from warranty.
SIMPLIFIED UE DECLARATION OF CONFORMITY
The manufacturer, Digicom S.r.l., declares that these radio equipments 4G Lift Dialer & 4G Lift Dialer Box , are compliant with
Directive 2014/53/UE.
The complete text of UE Declaration of Conformity is available at following internet address: www.digicom.it
ASSISTANCE AND CONTACTS
If, after carefully reading the procedures described, you are unable to resolve a possible problem, please contact Digicom
assistance. E-mail: [email protected]

II
4G Lift Dialer & 4G Lift Dialer Box Preface
III
4G Lift Dialer & 4G Lift Dialer Box Preface
SAFETY WARNINGS
Read these instructions and norms carefully before powering the device. Violation of such norms may be illegal and cause hazard
situations.
For any of the described situations please refer to the specific instructions and norms.
The device is a low power radio transmitter and receiver. When it is ON, it sends and receives radio frequency (RF) signals.
The device produces magnetic fields. Do not place it next to magnetic supports such as floppy disks, tapes, etc.
Operating your device close to other electrical and electronic equipment - such as a television, phone, radio or a personal
computer - may cause interferences.
INTERFERENCES
The device, like all other wireless devices, is subject to interferences that may reduce its performances.
ROAD SAFETY
Do not use your device while driving. In case of use on cars, you must check that the electronic equipment is shielded against RF
signals. Do not place the device in the air bag deployment area.
AIRCRAFT SAFETY
Switch off your device when on board aircrafts by disconnecting the power supply and deactivating the internal backup battery.
Using GSM devices on aircrafts is illegal.
HOSPITAL SAFETY
Do not use the device near health equipment, especially pacemakers and hearing aids, in order to avoid potential interferences.
Take care when utilizing the device inside hospitals and medical centres, which make use of equipment that could be sensitive to
external RF signals. Switch it off when use is expressly forbidden.
EXPLOSIVE MATERIALS
Do not use the device in refuelling points, near fuel or chemicals. Do not use the device where blasting is in progress. Observe
restrictions and follow any specific regulation or instruction.
INSTRUCTIONS FOR USE
Do not use this device in direct contact with the human body and keep a minimum distance of 20 cm from it and from the antenna.
Use approved accessories only. Consult the user's manual of eventual other equipment connected to this device. Do not connect
incompatible products.
INFORMATION TO USERS
according to Art. 26 "Information to Users" - Legislative Decree 14 March 2014, n. 49 "Actuation of the Directive 2012/19/UE on the
waste of electrical and electronic devices (RAEE)."
The symbol of a crossed waste container marked on the apparatus or on its package indicates that at the end of its useful life
the product must be collected separately from other waste materials.
The user must therefore take the apparatus which has reached the end of its useful life to appropriate separate collection
centres for electronic and electro-technical waste materials, or deliver it back to the reseller when purchasing a new apparatus
of an equivalent type for a domestic unit, giving one piece in for one piece out, according to Art. 11, paragraph 3 of the above
mentioned Legislative Decree.
Furthermore, as per Art.11, paragraph 3 of the above mentioned Legislative Decree it is possible, in the sale point, the free insertion of
recyclable materials into appropriate receptacle, without any purchasing obligation for the very small size RAEE, coming from domestic units.
Suitable separate waste collection for then sending the cast-off apparatus for recycling, treatment and environmentally friendly disposal,
contributes towards preventing any possible negative effects on the environment and on health and encourages recycling of the materials
the apparatus is made up of.
Unauthorised disposal of the product by the user will lead to payment of the administrative sanctions in force in the country where it is put
on the market.

TM
4G Lift Dialer & 4G Lift Dialer Box Introduction
1.1
4G Lift Dialer & 4G Lift Dialer Box Introduction
1. INTRODUCTION
Thanks for purchasing a Digicom product!
4G Lift Dialer and Voice Box constitute a bidirectional Emergency phone for lifts system, compliant to EN 81-28, EN 81-20,
EN 81-70 regulations.
The Emergency phone allows the users blocked in a lift cabin to send an alarm via GSM to
a Service Center or to the authorized Technical people.
In the lift cabin the emergency call is activated by pressing the alarm button connected to
the VoiceBox terminal board.
The people in the lift cabin will be reassured with a comfort message and a yellow bright
light will turn on to indicate that the alarm has been sent. At the same time the Emergency
phone calls the Service Center or the technical people (these numbers must be set by the
lift manager installer).
When the Emergency phone establishes the voice
communication with the Service Center, the people in
the cabin will see that a green light turns on indicating
that the alarm has been received and they will be
able to have a speakerphone conversation with the
technical people in order to receive assistance.
1.1. TECHNICAL FEATURES
• Module 4G/LTE-FDD
- 4G/LTE bands 3/7/20 (1800/2600/800 MHz)
- DCS band 3 (1800 MHz)
- E-GSM band 8 (900 MHz)
• Power
- 4G/LTE Power Class 3 (23 dBm)
- GSM/GPRS (GSMK) Power Class 4 (33 dBm) for band E-GSM
Power Class 1 (30 dBm) for band DCS
- EDGE (8-PSK) Power Class E2 (27 dBm) for band E-GSM
Power Class E2 (26 dBm) for band DCS
• Bluetooth Low Energy (BLE) radio module
- Working frequencies: from 2.402 to 2.480 GHz
- Maximum transmission power: +4 dBm
• Voice Interface: FXS on Screw Terminal Board
• Voice Call
• Data Call
• RS232 Serial Interface On RJ45 Female Connector For DATA connections
• GPRS class 10
• GSM Speed Up to9600 bps
• Built-in TCP/IP Stack
• Led for Indication of device status
• Kit for DIN Mounting (for code 8D5896 only)
• Metal Case for wall mounting (for code 8D5896B only)
• SMA connector for antenna
• USB port for Firmware Upgrade
• Reset Button (Restart – Alarm End)
• 2 Relays (max 60 Vcc/Vac – 2A)
• Power: 12-24Vcc – 1A min
• Rechargeable backup Battery (for code 8D5896B only)
• CE Marks and rohs compliants
• EN 81-28 , EN 81-20 , EN 81-70

1.2
4G Lift Dialer & 4G Lift Dialer Box Introduction
1.3
4G Lift Dialer & 4G Lift Dialer Box Introduction
1.2. SYSTEM DESCRIPTION AND PACKAGE CONTENT
Digicom Emergency phone for lift system is composed by two main elements:
4G Lift Dialer Remote alarm dialer with native integrated 4G/LTE module.
Voice Box Speakerphone unit with integrated microphone and speaker.
Voice Box speakerphone unit is connected to 4G Lift Dialer Emergency phone with 2 wires only.
For a good audio quality we suggest the use of a twisted pair for the connection.
Otherwise it is possible:
- to use two unused wires already present in the cabin cable;
- to use the two wires already present that are used for the bell, after having modified the system as described in paragraph
RELAYS1: BELL MANAGEMENT.
In these cases the audio quality could not be so good.
4G Lift Dialer remote alarm dialer is available in the following versions:
Emergency phone on DIN guide support (code 8D5896)
Suggested for installations inside the frame controller.
It is supplied with:
• 4G/LTE antenna with magnetic base and 3 meters cable.
Accessories that can be purchased separately:
• external power supply 230Vac / 12Vdc – 1000mA (code 8D6065);
• rechargeable battery Li-Pol 3,7Vdc – 4000mAh (code 724000163401).
Emergency phone integrated in metal box (code 8D5896B)
Suggested for installations in the machine room.
It is supplied with:
• 4G/LTE antenna with magnetic base and 3 meters cable;
• external power supply 230Vac / 12Vdc – 1000mA;
• rechargeable internal battery Li-Pol 3,7Vdc – 4000 mAh;
• screws for wall mounting.

1.2
4G Lift Dialer & 4G Lift Dialer Box Introduction
1.3
4G Lift Dialer & 4G Lift Dialer Box Introduction
Voice Box speakerphone unit, only 19mm thick and powered directly by 4G Lift Dialer Emergency phone, is available in the
following versions:
Voice Box Car (cod. 8D5804)
For the installation in car behind the car operating panel.
Equipped with:
• integrated microphone and speaker;
• integrated light signals;
• pin on terminal board to connect the N.O. or N.C. buttons accessible in the cabin;
• pin on terminal board to connect the N.O. or N.C. buttons accessible by technical people on the
Top of the cabin and in Pit;
• pin on terminal board to connect the external light signals of alarm sent and alarm received.
Voice Box Top/Pit (code 8D5780 & 8D5780PW)
For the installation on the Top of the cabin and in Pit with microphone and speaker.
Equipped with:
• integrated microphone and speaker;
• integrated alarm button;
• reset alarm button;
• integrated light signals.
Voice Box Button (code 8D5810)
For the installation on the Top of the cabin and in Pit without microphone and speaker.
Equipped with:
• alarm button only.
This model must be connected to VoiceBox Car and it won't be connected to 4G Lift Dialer Emergency
phone.

TM
4G Lift Dialer & 4G Lift Dialer Box Installation
2.1
4G Lift Dialer & 4G Lift Dialer Box Installation
2. INSTALLATION
Here below the procedure for the installation and configuration of 4G Lift Dialer and Voice Box together.
This user's manual can be used for the following models of 4G Lift Dialer:
• (code 8D5896) Emergency phone on DIN rail support: 4G Lift Dialer
• (code 8D5896B) Emergency phone integrated in metal box: 4G Lift Dialer Box
The user's manual also refers to the following models:
• (code 8D5780) Speakerphone unit: Voice Box Top/Pit or Under Car
• (code 8D5804) Speakerphone unit : Voice Box Car
• (code 8D5810) Button: Voice Box Button
2.1. SUGGESTIONS FOR SECURITY
Before installing Digicom Emergency phone, please read this user's manual.
Pay attention to your security during the installation of Emergency phone for Lifts system.
We suggest to operate in an open lift shaft with proper equipment like safety harness.
We also suggest to disconnect power supply before operating near high voltage like for example in an lift motor room.
2.2. INSTALLATION ARCHITECTURES
As previously described, speakerphone Voice Box is connected to 4G Lift Dialer Emergency phone with 2 wires only.
For a good audio quality we suggest the use of a twisted pair for the connection.
Otherwise it is possible:
- to use two unused wires already present in the cabin cable;
- to use the two wires already present that are used for the bell, after having modified the system as described in paragraph
RELAY1: BELL MANAGEMENT.
In these cases the audio quality could not be so good.
The following installation architectures suggested by Digicom can be used both for new systems and for modernizations
independently by the Digicom Emergency phone card used and by its allocation, the possible installations can be:
• BASE INSTALLATION (see installation scheme in the next pages)
Connection of a Voice Box in car to 4G Lift Dialer, placed directly behind the car operating panel. Then 3 external buttons will
be connected to Voice Box Car:
• Car = 1 Voice Box Car placed directly behind the car operating panel with the external button.
• Top / Pit = 2 external button can be placed on the Top and/or Pit. For the connection of Top and/or Pit buttons it is possible
to use the model Voice Box Button.
• COMPLETE TRIPHONY INSTALLATION (see installation scheme in the next pages)
This architecture connects a maximum of 3 speakerphone units to 1 4G Lift Dialer Emergency phone:
• Car = 1 Voice Box Car placed directly behind the car operating panel with the external button.
• Top / Pit = 2 Voice Box Top / Pit.
Furthermore in all architectures it will be possible to connect a common phone to the 4G Lift Dialer for the intercom function
between the frame controller and the lift cabin.The same phone can be also used for the local configuration and for the recording
of the eventual alarm message.

2.2
4G Lift Dialer & 4G Lift Dialer Box Installation
2.3
4G Lift Dialer & 4G Lift Dialer Box Installation
ALARM
ALARM
8D5810 Voice Box Button
8D5804 Voice Box Car
CAR
N.O. or N.C.
External Alarm Button
EXTERNAL LIGHTS
Sent/Received Alarm
External Power supply:
20mA - 30Vdc max
+Vcc GND
1
11
2 3
7 8 9
PIT
11
TOP
4
4
4
11
8D5810 Voice Box Button
BASE INSTALLATION 1. Insert the SIM card; 2. Connect the antenna; 3. Connect the VoiceBox; 4. Connect the Alarm button/s [*]; 5. Switch-on the 4G Lift Dialer; 6. Check the Power Led is ON; 7. Check the GSM Led is Blinking or ON; 8. Configure the 4G Lift Dialer. [*] = The button must have 2 contacts to
separate the activation circuit of the alarm call from the bell circuit.
N.O.
Alarm Button
or
N.O. COM. N.C.
N.O.
Alarm Button
or
N.O. COM. N.C.
GND
+Vdc (12-24Vdc - 1A min)
Pins can be crossed
Pins can be crossed
Pins can be crossed
4G Lift Dialer
3 4 5 6 2221
CONFIG
GSM
POWER
Phone for:
- Configuration
- Intercom
SEE OTHER TYPE
INSTALLATION IN THE
NEXT PAGE

2.2
4G Lift Dialer & 4G Lift Dialer Box Installation
2.3
4G Lift Dialer & 4G Lift Dialer Box Installation
ALARM
ALARM
8D5810 Voice Box Button
8D5804 Voice Box Car
CAR
N.O. or N.C.
External Alarm Button
EXTERNAL LIGHTS
Sent/Received Alarm
External Power supply:
20mA - 30Vdc max
+Vcc GND
1
11
2 3
7 8 9
PIT
11
TOP
4
4
4
11
8D5810 Voice Box Button
BASE INSTALLATION 1. Insert the SIM card; 2. Connect the antenna; 3. Connect the VoiceBox; 4. Connect the Alarm button/s [*]; 5. Switch-on the 4G Lift Dialer; 6. Check the Power Led is ON; 7. Check the GSM Led is Blinking or ON; 8. Configure the 4G Lift Dialer. [*] = The button must have 2 contacts to
separate the activation circuit of the alarm call from the bell circuit.
N.O.
Alarm Button
or
N.O. COM. N.C.
N.O.
Alarm Button
or
N.O. COM. N.C.
GND +Vdc (12-24Vdc - 1A min)
Pins can be crossed
Pins can be crossed
Pins can be crossed
4G Lift Dialer
3 4 5 6 2221
CONFIG
GSM
POWER
Phone for:
- Configuration
- Intercom
SEE OTHER TYPE
INSTALLATION IN THE
NEXT PAGE

2.4
4G Lift Dialer & 4G Lift Dialer Box Installation
2.5
4G Lift Dialer & 4G Lift Dialer Box Installation
4G Lift Dialer
3 4 5 6 2221
CONFIG
GSM
POWER
Reset ALARM
Reset ALARM
COMPLETE TRIPHONY INSTALLATION
CAR
8D5780 Voice Box Top Pit
N.O. or N.C.
External Alarm Button
Jumper for top position
Jumper for pit position
No jumper for car position
8D5804 Voice Box Car
GND
+Vdc (12-24Vdc - 1A min)
EXTERNAL LIGHTS
Sent/Received Alarm
External Power supply:
20mA - 30Vdc max
+Vcc GND
1
11
2 4
7 8 9
PIT
1 2
11 12
TOP
2
10 11
1
8D5780 Voice Box Top Pit
Pins can be crossed
1. Insert the SIM card; 2. Connect the antenna; 3. Connect the VoiceBox; 4. Connect the Alarm button/s [*]; 5. Switch-on the 4G Lift Dialer; 6. Check the Power Led is ON; 7. Check the GSM Led is Blinking or ON; 8. Configure the 4G Lift Dialer. [*] = The button must have 2
contacts to separate the activation circuit of the alarm call from the bell circuit.
Phone for:
- Configuration
- Intercom
SEE OTHER TYPE
INSTALLATION IN THE
PREVIOUS PAGE

2.4
4G Lift Dialer & 4G Lift Dialer Box Installation
2.5
4G Lift Dialer & 4G Lift Dialer Box Installation
4G Lift Dialer
3 4 5 6 2221
CONFIG
GSM
POWER
Reset ALARM
Reset ALARM
COMPLETE TRIPHON INSTALLATION
CAR
8D5780 Voice Box Top Pit
N.O. or N.C.
External Alarm Button
Jumper for top position
Jumper for pit position
No jumper for car position
8D5804 Voice Box Car
GND
+Vdc (12-24Vdc - 1A min)
EXTERNAL LIGHTS
Sent/Received Alarm
External Power supply:
20mA - 30Vdc max
+Vcc GND
1
11
2 4
7 8 9
PIT
1 2
11 12
TOP
2
10 11
1
8D5780 Voice Box Top Pit
Pins can be crossed
1. Insert the SIM card; 2. Connect the antenna; 3. Connect the VoiceBox; 4. Connect the Alarm button/s [*]; 5. Switch-on the 4G Lift Dialer; 6. Check the Power Led is ON; 7. Check the GSM Led is Blinking or ON; 8. Configure the 4G Lift Dialer. [*] = The button must have 2
contacts to separate the activation circuit of the alarm call from the bell circuit.
Phone for:
- Configuration
- Intercom
SEE OTHER TYPE
INSTALLATION IN THE
PREVIOUS PAGE

2.6
4G Lift Dialer & 4G Lift Dialer Box Installation
2.7
4G Lift Dialer & 4G Lift Dialer Box Installation
2.3. TESTS DURING THE INSTALLATION
Locate a proper position for the various parts of the system and before the final mounting check the following:
• 4G Lift Dialer Emergency phone
• SIM correctly inserted;
• antenna connector screwed until its end point;
Apply the magnetic base of the antenna only on metal zone, without connection to earth
Please use eventually the metal support, find in the package, fixed it to the wall
• good GSM signal: yellow led on or blinking;
• correct connection and correspondence of the cables to the pins of terminal board;
• terminal board screws tightened all the way down;
• terminal board completely fitted on the 4G Lift Dialer.
• Voice Box speakerphone
• Once Voice Box has been placed behind the car operating panel, it won't be possible anymore to access the terminal board
for connections;
• connection to the terminal board of the 2 wires coming from 4G Lift Dialer;
• connection of the 2 wires for the lift alarm button:the button must a 2 contact buttons to separate the circuit for the activation
of the alarm call from the bell circuit;
• for model 8D5780, jumper to identify Top – Pit;
• correct display of the light signals behind the car operating panel;
• correct correspondence of the microphone behind the hole on the car operating panel;
• correct correspondence of the speaker behind the holes on the car operating panel.
Once the installation is completed you can go on with the configuration of the Emergency phone in few minutes with one of
the following possibilities, as you prefer:
• Application for Android smartphones: via SMS or BLE;
• via SMS by mobile phone;
• with telephone or mobile phone calling the 4G Lift Dialer;
• with a common DTMF phone connected to pins 3-4 of 4G Lift Dialer.

2.6
4G Lift Dialer & 4G Lift Dialer Box Installation
2.7
4G Lift Dialer & 4G Lift Dialer Box Installation
2.4. BEFORE POWERING LIFT DIALER ON
Place 4G Lift Dialer where you prefer, in a zone with a good GSM signal, and go on as follows:
1. Open the SIM holder by slightly pressing and pushing it horizontally toward
the internal side of the card.
Now insert the SIM card. Pay attention to the SIM cut corner and be sure
the golden contacts of the SIM are turned downwards when closing the SIM
holder.
Close the SIM holder by slightly pressing and pushing it horizontally in the
opposite side to block it and correctly fix the SIM.
2. Connect the LTE antenna you find in the package to the golden SMA
connector. Screw it clockwise; in case of problem do not force but remove
the antenna and try again.
Apply the magnetic base of the antenna only on metal zone,
without connection to earth.
Please use eventually the metal support, find in the package,
fixed it to the wall.
3. Connect pins 5-6 of 4G Lift Dialer to pins 1-2 of Voice Box.
PINS CAN BE CROSSED.
For a good audio quality use a twisted pair for the connection. Otherwise you can use two unused wires already present in the
car cable or use the the wires already present and used for the bell after having modified the system as described in paragraph
RELAY1: BELL MANAGEMENT.
In this case the audio quality could not be the best one.
4. Connect eventually the external button (or buttons) on Voice Box.
5. Now power 4G Lift Dialer on following the polarity:
pin 21 : 12-24 Vdc
pin 22 : GND
We suggest to use Digicom power supply for 4G Lift Dialer:
Switching power supply (IN: 100-240 Vac / 50-60Hz / 0,5A – OUT 12 Vdc / 1A) (code 8D6065)
USE ONLY A LIMITED POWER SOURCE (LPS) POWER SUPPLY, ACCORDING TO EN 60950-1 (2.5) REQUIREMENTS.
6. Check the LED power on:
Power: green fixed ON
GSM: at the beginning OFF; after the affiliation to the GSM network it is yellow fixed ON or blinking.
7. For the first alarm call after powering, wait 1 minute, in this time 4G Lift Dialer completes the internal initializations.
SIM
1 5 10 15 20
BATTERY
SCREW TERMINAL
ANTENNA
22

2.8
4G Lift Dialer & 4G Lift Dialer Box Installation
2.9
4G Lift Dialer & 4G Lift Dialer Box Installation
2.5. VOICE BOX CONNECTION
Place the Voice Box(es) where you prefer and go on as follows:
1. Switch Off the 4G Lift Dialer.
2. Connect pins 5-6 of 4G Lift Dialer to pins 1-2 of Voice Box.
PINS CAN BE CROSSED.
For a good audio quality use a twisted pair for the connection. Otherwise you can use two unused wires already present in the
car cable or use the the wires already present and used for the bell after having modified the system as described in paragraph
RELAY1: BELL MANAGEMENT.
In this case the audio quality could not be the best one.
3. Set Voice Box as Car-Top-Pit
For model 8D5804
Voice Box Car = Factory Default (no Jumper)
For model 8D5780
Voice Box Top = Close Pin 10-11
Voice Box Pit = Close Pin 12-11
Maximum 3 Voice Box Can be present in the system.
4. Connect the external alarm button for the car to pin 4-11 of Voice Box.
The button can be N.O. or N.C.The button must have 2 contacts to separate the activation circuit of the alarm call from the bell
circuit.
5. Connect the eventual external alarm button for Top - Pit to pins 3-11 of Voice Box.
The buttons installed on Top or in Pit, for technical people, can be N.O. or N.C. It is necessary that both buttons have the same
configuration: both N.O. or both N.C.
6. Connect the eventual external signal of Sent Alarm to pins 7-9.
7. Connect the eventual external signal of Received Alarm to pins 8-9.
8. Now turn on the il 4G Lift Dialer: wait 1 minute before run the alarm call, in this time 4G Lift Dialer complete the internal
initializations.

2.8
4G Lift Dialer & 4G Lift Dialer Box Installation
2.9
4G Lift Dialer & 4G Lift Dialer Box Installation
2.6. 4G LIFT DIALER PINOUT
PIN DESCRIPTION
1 NOT USED
2 NOT USED
3 PHONE
4 PHONE
5 VOICE BOX
6 VOICE BOX
7 IN F (ALARM FILTER)
8 IN SOS
9 IN T (TECHNICAL ALARM)
10 GND (IN F , IN SOS , IN T)
11 GND
12 RELAY1 - N.O.
13 RELAY1 - COM
14 RELAY1 - N.C.
15 RELAY2 - N.O.
16 RELAY2 - COM
17 RELAY2 - N.C.
18 BATTERY [+] *
19 BATTERY [-] *
20 GND
21 POWER (12-24Vdc) [ + ]
22 GND
* The battery with connector (code 7D1991) can be connected to the specific connector present on 4G Lift Dialer; if the battery
has no connector, it can be connected to pins18-19 of the terminal board, paying attentions to the polarity.
We suggest to use Digicom power supply for 4G Lift Dialer:
Switching power supply (IN: 100-240 Vac / 50-60Hz / 0,5A – OUT 12 Vdc / 1A) (code 8D6065)
USE ONLY A LIMITED POWER SOURCE (LPS) POWER SUPPLY, ACCORDING TO EN 60950-1 (2.5) REQUIREMENTS.
2.7. LIFT DIALER TOPOGRAPHY
SERIAL PORT RS232
USB PORT
RS232 ENABLED
SIM HOLDER
1 5 10 15 20
BATTERY
SCREW TERMINAL
ANTENNA
RESET
CONFIG
GSM
POWER
22
1 8

2.10
4G Lift Dialer & 4G Lift Dialer Box Installation
2 .11
4G Lift Dialer & 4G Lift Dialer Box Installation
2.8. VOICE BOX - CAR PINOUT (CODE 8D5804)
PIN DESCRIPTION
1 LIFT DIALER
2 LIFT DIALER
3 EXTERNAL ALARM BUTTON IN TOP and/or PIT (N.O. or N.C.)
4 EXTERNAL ALARM BUTTON IN CAR (N.O. or N.C.)
5 HEARING LOOP ( - )
6 HEARING LOOP ( + )
7 EXTERNAL LED: ALARM SENT (YELLOW LIGHT)
8 EXTERNAL LED: ALARM RECEIVED (GREEN LIGHT)
9 GND FOR EXTERNAL LEDS
10 NOT USED
11 GND FOR EXTERNAL ALARM BUTTON
12 NOT USED
For a good audio quality we suggest the use of a twisted pair for the connection.
Otherwise it is possible:
- to use two unused wires already present in the cabin cable;
- to use the two wires already present that are used for the bell, after having modified the system as described in paragraph
RELAY1: BELL MANAGEMENT.
In these cases the audio quality could not be so good.
The buttons installed on Top or in Pit, for technical people, can be N.O. or N.C. It is necessary that both buttons have the same
configuration: both N.O. or both N.C.
2.9. VOICE BOX - CAR TOPOGRAPHY (CODE 8D5804)
1
12
SCREW TERMINAL
SPEAKERPHONE
ALARM SENT LED ALARM
RECEIVED LED
MICROPHONE
RESET
BUTTON
FIXING HOLES