Swann SW276-ASL User manual

Theft Deterrent Kit / Anti-Shoplifting Kit
www.swannsecurity.com
8. Warranty Information
Quick Start Guide
SW276-ASL / SW276-RSL / SW276-TSL
STOP
If this product does not work when you first plug
it in or you have any concerns, don’t take it back
to the store!
Use the Installation Guide / Manual in the pack, or
Visit www.swannsecurity.com/help
for FAQs, troubleshooting hints & more, or
Contact our expert Tech Support Team...
Email - [e-mail]
United States 1-800-627-2799
1-877-274-3695
Sun 4pm-12am, Mon-Fri 8am-12am (PDT)*
Australia 1300 138 324
Mon 9am-5pm, Tues-Fri 1am-5pm (AET)
Sat 1am-9am
New Zealand 0800 479 266
Mon 11am-7pm, Tues-Fri 3am - 7pm
Sat 3am-11am (NZDT)
International [phone]
Mon 9am-5pm, Tues-Sat 1am-9am (AET)
*Hours vary during daylight savings times
has the answers
Swann Communications warrants this product
against defects in workmanship and materials for a
period of one (1) year from the original purchase
date. You must present your receipt as proof of
date of purchase for warranty validation.
Any unit which proves defective during the stated
period will be repaired without charge for parts
or labour or replacement at the sole discretion of
Swann. The repair or replacement will be war-
ranted for either ninety days or the remainder of
the original one year warranty period, whichever is
longer.
The end user is responsible for all freight charges
incurred to send the product to Swann’s repair
centers. The end user is responsible for all ship-
ping costs incurred when shipping to and from any
country other than the country of origin.
The warranty does not cover any incidental, ac-
cidental or consequential damages arising from the
use of or the inability to use this product.
Any costs associated with the fitting or removal of
this product. Any costs associated with the fitting
or removal of this product by a tradesman or other
person or any other costs associated with its use
are the responsibility of the end user.
This warranty applies to the original purchaser
of the product only and is not transferable to any
third party.
Unauthorized end user or third party modifications
to any component or evidence of misuse or abuse
of the device will render all warranties void.
FCC WARNING STATEMENT:
This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation
NOTE: All jurisdictions have specific laws and regulations relating
to the use of cameras. Before using any camera for any purpose it
is the buyer’s responsibility to be aware of all applicable laws and
regulations that prohibit or limit the use of cameras and to comply
with the applicable laws and regulations.
110408EN

1. Package Contents
4. Affixing Cameras
3. Adjusting Camera Angle
7. Where to Place Security Stickers
5. Affixing Imitation Dome Cameras
6. Placing Cameras
2. Attaching Camera Stands
3 or 4 x MaxiBrite Imitation Camera
3 or 4 x MaxiBrite Stand
4 x Small Security Sticker
Large Security Sticker Sign
4 x Imitation Dome Cameras
Mounting Hardware
Quick Start Guide
Swann Communications • Toll Free Technical Support: USA - 1-800-627-2799, 1-877-274-3695, Australia - 1300 13 8324 • Email: [email protected] www.swannsecurity.com
Screw the stand into the
camera and twist clockwise
to tighten
1. Find an appropriate
location to mount camera
Turn the knob to loosen
the stand and camera and
turn again to tighten
1. Find an appropriate
location to mount camera
2. Detach stand from
camera
2. Clean surface when
dome will be applied
3. Use provided scews to
fix stand to surface
1. In front windows
2. On side windows
3. On gates/doors
4. Near an obvious camera
5. On shed doors
6. Near cash registers
7. In warehouse
8. In parking lot
Place cameras near entry points such as front or
rear doors, garage etc. Place under eaves and aim
towards the garage or down the driveway
3. Peel back double-sided
adhesive
4. Re-attach camera to
stand and adjust angle
4. Carefully place rim on
surface and hold for 30s
The camera stand can also be
fixed to the top of the camera
for more versatile applications