Pandora Mini v3 User manual

Pandora would like to thank you for choosing our
service-security system
Pandora Mini v3 is a car service-security system, built for cars with on-
board voltage of 12V.
It is a complex engineering product, which includes unique and modern
software and hardware solutions. When building the Pandora Mini v3 we were
using the most up-to-date electronics from world’s best manufacturers. The
device is built using high-precision mounting and control machinery, thus we
guarantee highest possible quality, reliability and stable technical characteris-
tics for the whole operation period.
Elegant and advanced technical design and unique ergonomic interaction
algorithms that are used in the Pandora Mini v3 allow enhancing your car with
fantastic set of intuitive and useful functions.
This device has limited external factors resistance. It should not be subjected to water beyond occasional splatter, or operated in
temperatures outside -40° to +80° C range.
Our web site: www.pandorainfo.com
Customer support: [email protected]om
WARNING! ItIs stRoNGly AdvIsed to hAve pRofessIoNAl cAR mechANIc IN-
stAllING the system. ANy cAR electRoNIcs INstAlleR should be Able to INstAll
the pANdoRA mINI v3 usING INstAllAtIoN scheme IN thIs mANuAl ANd AlARm
studIo softWARe. most feAtuRes ARe hIGhly depeNdeNt oN competeNt IN-
stAllAtIoN. ouR systems ARe thoRouGhly tested foR quAlIty, so If AfeAtuRe
fAIls to pRoduce expected Result, most lIkely the pRoblem Is IN ImpRopeR
INstAllAtIoN.
Product is in conformity with Electromagnetic Compatibility
Directive EMC 2004/108/EC and R&TTE Directive 1999/5/EC

32 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Table of contents
System set 4
System features 5
Base unit 5
Control and monitoring 5
Arming mode 7
Multi-button code immobilizer 7
Immobilizer mode 8
Anti-Hi-Jack mode 8
Anti-Hi-Jack2 mode 9
Immobilizer radio tag 9
Functions of the button 10
Light indication of SEND LED 10
Replacing an immobilizer tag battery 11
Updating firmware of the tag 11
Mobile applications 12
Using the application 13
Control over the system 16
Arming 16
Disarming 17
Service (VALET) mode 19
Control over the system in case of emergency 20
Emergency disabling immobilizer radio tags 22
System installation 24
Wiring diagram 24
General installation requirements 26
Wiring description 27
System configuration and programming 29
Entering the programming mode 29
Exiting the programming mode 29
Pandora Alarm Studio 30
Programming menu 31
Programming levels table 32
Additional information 40
Siren sounds and light signalizations 40
Beeper sound signals 40
Meaning of the LED indicator colors 41
Checking the number of recorded radio tags 41
Additional devices 42
System module layout 45
Warranty obligations 46
Installation certificate 47
Acceptance certificate 48
Warranty card 48

54 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
System set
Base unit 1
Immobilizer tag 2
Blocking relay 1
Cable with VALET button 1
User installation manual 1
Personal owner’s card 1
Beeper (compact sound emitter) 1
Main cable 1
Fastening kit 1
Packaging 1
mANufActuReR ReseRves the RIGht to chANGe set ANd coNstRuctIoN of the pRod-
uct to ImpRove Its techNoloGIcAl ANd opeRAtIoNAl pARAmeteRs WIthout NotIfIcA-
tIoN.
SYSTEM FEATURES
Base unit
• Integrated 2.4 GHz module with support of Bluetooth 5.0
• Built-in integral accelerometer for deterMini v3ng motion/shock/tilt with
adaptive processing algorithm and sensitivity controls
Built-in micro-USB port
• Integrated temperature sensor (interior temperature)
• Dialog coding of control commands with 128-bit encryption keys (a key is
changed each time an additional device is recorded)
• Individual “Secret PIN-code”, changeable “Service PIN-code” and “Immobi-
lizer PIN-code”
Control and monitoring
Control of the vehicles zones depends on the type of connection and system
settings, original car operation and trim.
Analog connection – It is a direct connection of analog inputs and outputs
to electrical circuits of a vehicle in accordance with a connection diagram.
Digital connection – It is a connection to digital (CAN, LIN) buses. It allows
reading information (statuses) and controlling vehicles (commands) by digital
buses of the vehicles. The detailed information about digital protocols is avail-
able on loader.pandorainfo.com. The declared statuses may not be available
for certain vehicle trims.
Built-in sensors – These sensors are integrated in the base unit. The sensors
perform control and protection of the vehicle. Additional connections are not
required
Additional sensor (*optional) – External additional sensors are connected
to the base unit.

76 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Analog connection Digital connection Built-in sensors Additional sensors
Guarded and monitored zones
• • •* Interior temperature (status)
• •* Engine temperature (status)
• •* Outside sensor (status)
•Voltage of the on-board circuits (status, security zone – alarm
level)
•Shock sensor (security zone – alarm and warning level)
•Motion sensor (security zone – alarm level)
•Tilt sensor (security zone – alarm level)
• •* OE alarm system status via CAN, additional sensor,
(status, security zone – alarm and warning level)
• • Turning ignition on (status, security zone – alarm level)
• • Opening doors, separate indication for each door via CAN
(status, security zone – alarm level)
• • Opening a trunk (status, security zone – alarm level)
• • Pressing brake (status, security zone – alarm level)
• • Engine operation control - RPM (status)
• • Position of a gearbox selector/handbrake(status)
•“Parking light is not turned o” notication
Control (Commands)
• • Central lock
•Car original alarm system
• • Trunk
• • Turn lights
• • Closing windows
•CAN •* Engine pre-heaters
Arming mode
The arming mode monitors guarded zones and provides engine blocking. If
one of the guarded zones is triggered, the system will record this event in its
non-volatile memory, activate the alarm or warning mode and inform an own-
er with an indication of the zone. If the system is armed, the engine is running,
and one of the guarded zones is triggered, the system will stop the engine.
Arming/disarming, alarm mode and warnings are accompanied by sound and
light signals. The system confirms arming with 1 sound signal and 1 flash of the turn
indicators. The system confirms disarming with 2 short sound signals and 2 flashes of
the turn indicators. If one of the guarded zones is opened, the system will produce
4 warning sounds and 4 flashes of the turn indicators at the moment of arming. The
system will also produce 4 warning sounds and 4 flashes of the turn indicators at the
moment of disarming if there were alarm events during the armed period. The system
activates light and sound signals for 30 seconds in the alarm mode. The alarm signals
can be canceled by an arming or disarming command. If a warning zone is triggered,
the system will produce 1 sound signal and 1 flash of the turn indicators.
If one of the guarded zones fails, the system will forcibly turn off this zone.
If a switch triggers more than 9 times in a row, it will be disabled until the next
arming. The shock/tilt/motion sensor is temporarily deactivated (15 sec.) if it
has been triggered more than 3 times in a row.
Multi-button code immobilizer
Multi-button code immobilizer (pin-to-drive) is a function that allows dis-
arming, disabling blocking and controlling service mode and time channels
using original vehicle controls (button, lever or pedal) and a pre-programmed
PIN-code (the “Immobilizer PIN-code”). The function works using special
analog inputs or digital buses of a car.
An example of using the function:
• Turn on the ignition to disable engine blocking or service mode, turning on the
ignition is not required if you want to disarm the system or control time channels.
• Enter the “Immobilizer PIN-code”. Press a programmed button/lever/pedal
the number of times equals to the first digit. Pauses between presses should
not exceed 1 second. More than 1 second pause will be interpreted as the
start of the next digit input. The immobilizer code can consist max of 4 digits
from 1 to 9.
• The system will confirm the correct input by a sound signal of the beeper
and a programmed function will be performed.

98 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Note! ItIs RequIRed to mAke AddItIoNAl coNNectIoNs ANd settINGs to use thIs
fuNctIoN.
Immobilizer mode
When switching on the ignition, a base unit of the security system per-
forms a search for immobilizer tags in radio zone. If no radio tags are detected
at the time of switching on the ignition, the system will block the engine. En-
gine blocking will occur immediately or at the time a motion sensor detects
movement, it depends on the system settings.
WARNING! Ifthe system does Not RecoGNIze ARAdIo tAG, the beepeR WIll
emIt 5 souNd sIGNAls WheN the IGNItIoN Is tuRNed oN, thIs WIll RepeAt 5
tImes. check ARAdIo tAG bAtteRy, move AtAG (It Goes to the sleep mode
WheN It RemAINs motIoNless ANd the IGNItIoN Is off. A buIlt-IN AcceleRom-
eteR hAve to RecoGNIze movemeNt to ActIvAte AtAG).
Note! thIs mode Is eNAbled by defAult. use the pANdoRA bt oR pANdoRA AlARm
studIo to eNAble/dIsAble thIs mode.
Anti-Hi-Jack mode
The Anti-Hi-Jack mode helps to prevent aggressive seizure of a car using
delayed engine blocking on door opening. Every time on opening/closing a
door when the ignition is on, the system requests a response from a radio tag
using a unique algorithm. After a door was opened while the ignition is on, if
the system cannot detect a radio tag, the engine will be stopped after 1 minute
(general safety requirement). The siren will play the‘ENGINE BLOCKING WARN-
ING’ ringtone before blocking. The engine will be blocked immediately or at
the time the car starts moving, it depends on system settings. Blocking will be
disabled if the system detects a radio tag.
Note! thIs mode Is dIsAbled by defAult. use the pANdoRA bt oR pANdoRA AlARm
studIo to eNAble/dIsAble thIs mode.
Anti-Hi-Jack 2 mode
The Anti-Hi-Jack-2 mode helps to prevent aggressive seizure of a car using
delayed engine blocking on radio tag disappearance. The system constantly
requests a response from a tag using a unique algorithm when the ignition is
on. If the system cannot detect a radio tag, the engine will be stopped after 1
minute (general safety requirement for car movement). The siren will play the
‘ENGINE BLOCKING WARNING’ringtone before blocking. When warning signals
end, the system will block the engine. Engine blocking will occur immediately
or at the time the car starts moving, it depends on block implementation and
system settings.
Note! thIs mode Is dIsAbled by defAult. use the pANdoRA bt oR pANdoRA AlARm
studIo to eNAble/dIsAble thIs mode.
IMMOBILIZER RADIO TAG
Radio tag is a control device of security and anti-theft functions of the sys-
tem used for concealed carrying. The tag is used to authorize an user in the
radio coverage zone of the base unit for such modes as “Immobilizer”, ”Hands-
Free”, ”Slave”.
The tag has a control button for arming/disarming and switching on and
off the service mode. A built-in motion sensor allows the tag to go into energy
saving mode when there is no movement. The tag also has a LED indicator
”SEND”.
• Control button
• Built-in LED indicator“SEND”
• Built-in accelerometer
• Battery CR 2032
• 2.4 GHz radio frequency (dialog encryption AES-128)
• Bluetooth-protocol
SEND

1110 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
WARNING! ItIs Not RecommeNded to plAce the tAG Next to metAl
objects, mAGNetIc ANd electRoNIc devIces(mAGNetIc ANd cRedIt cARds,
phoNes, keys, key fobs, etc.) foR coRRect opeRAtIoN. doNot expose the tAG
to hIGh tempeRAtuRes, moIstuRe. ItIs RecommeNded to plAce the tAG oN the
belt oR IN the fRoNt pocket of youR clothING
Functions of the button
ACTION FUNCTION
- briey
(ignition is o)
Arm/disarm
- hold for 3 seconds
(system is disarmed)
Activate/deactivate Service mode
- hold for 6 seconds Pair a tag with the base unit
- hold for 10 seconds Firmware update
Light indication of SEND LED
SIGNAL DESCRIPTION
1 ash Arming/disarming
Conrmation of arming
Low battery level (when installing a battery)
2 ashes Conrmation of disarming
3 ashes Battery is charged (when installing a battery)
faded Battery is discharged (when installing a battery,
when pressing the button)
Replacing an immobilizer tag battery
Carefully open the cover of the tag battery compartment. Remove a dis-
charged battery and insert a new one keeping in mind the correct polarity.
Replacing a battery will not cause a loss of tag code information, as au-
thorization data is stored in the non-volatile memory of the MCU Carefully
close the cover of the tag battery compartment. All elements of construction
should be rigidly locked in places. If it is so, the tag can be operated as usually.
Updating rmware of the tag
• Run the mobile app Pandora BT.
• Press and hold the button on the radio tag until the 10th flash of the SEND
indicator, then release the button.
• Select the found device in the app and select one of the update option:
INTERNET – firmware will be uploaded by an internet connection. FILE
MANAGER – firmware will be uploaded from the phone storage (only for
Android).
Note! Акт уАльнАя версия прогрАммного обеспечения доступнА нА сАйте
http://pANdoRAINfo.com/ (рАздел для зАгрузки «suppoRt» –> «AlARmstudIo &
fIRmWARe»).
Open here

1312 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
MOBILE APPLICATIONS
The mobile application Pandora BT for Android and iOS devices is a service
application to control and manage the system state via the Bluetooth connec-
tion. The mobile device must be paired with the system (see the“Installing the
app” section).
Note! the system suppoRts oNly oNe mobIle devIce
Installing the app
Download the mobile app from your device’s app store:
• App Store (iOS) – Pandora Pro;
• Google Play (Android) - Pandora Online.
Enter the system programming mode and pair your phone with the system
Note! mINImum RequIRemeNts foR mobIle devIces: pANdoRA oNlINe - ANdRoId
v4.4, bluetooth 4.0 loW eNeRGy; pANdoRA pRo - Ios v10 .
Enter the system programming mode after installing the app and make the
pairing procedure.
Pairing a mobile device
To pair a mobile device:
I. ENTER THE PROGRAMMING MODE
To enter the programming mode, enter the “Service PIN-code” using the
VALET button (factory pre-set is “1-1-1-1”). Entering the “Service PIN-code”(see
the “Control over the system in case of emergency”section).
II. ENTER THE“PAIRING A MOBILE DEVICE”PROGRAMMING LEVEL
Press and hold the VALET button for 5 seconds until the fifth sound signal
of the beeper or the fifth orange flash of the LED). Release the button after the
fifth sound signal. The system will enter the“Pairing a mobile device” program-
ming level. The LED indicator will light green after entering the level, it means
the system is ready for pairing.
III. PAIR A MOBILE DEVICE
Switch on the Bluetooth on your phone. . Run the Pandora BT app and go
to the “Devices -> Searching device” screen. The application will search for the
system via a Bluetooth connection. Select the found system (“Pair”), the system
and the mobile device will be automatically paired. It will be confirmed with a
sound signal of a siren and red and green flashes of the LED indicator.
IV. EXIT THE PROGRAMMING MODE
To finish the pairing procedure, exit the programming mode - switch on
the ignition and then switch it off.
Note! IfAmobIle devIce hAs beeN AlReAdy pAIRed, It WIll be deleted WheN
you eNteR thIs level. WheN you oveRWRIte the sAme devIce IN the system mem-
oRy, you should delete the bluetooth coNNectIoN oN youR mobIle devIce.
Note! IftheRe Is No AutomAtIc pAIRING, eNAble the “pIN Request foR phoNe pAIR-
ING” Item IN the “RAdIo tAG ANd mobIle devIce fuNctIoNs” settINGs ANd mAke the
pAIRING pRoceduRe AGAIN. A mobIle devIce WIll Request ApIN-code (fActoRy pRe-
set Is 0-0-1-1-1-1 WheRe 4 lAst dIGIts ARe the “seRvIce pIN-code”.
Using the application
Run the application when you are near the system in the Bluetooth radio range.
The application will automatically detect your system and will open the main
screen with the connected system.
Note! the pAIRed mobIle devIce cAN be used As AN oWNeR AuthoRIzAtIoN devIce
foR the “ImmobIlIzeR”, “ANtIhIJAck”, “hANdsfRee” modes. ItIs RequIRed to mAke
AddItIoNAl settINGs to ActIvAte thIs fuNctIoN. eNteR the pRoGRAmmING mode ANd
chANGe the folloWING settINGs IN the mobIle App: settINGs -> system set-
tINGs -> hANds fRee -> mobIle devIce.

1514 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
The main screen contains the follow-
ing information and functions:
IMAIN MENU - provides access to
event history, help, system and applica-
tion settings.
II VEHICLE – displays current status
information about the vehicle and sys-
tem.
Note! Ifyou WANt to chANGe vehIcle
type oR ApplIcAtIoN theme, Go to mAIN
meNu – settINGs - ApplIcAtIoN.
System modes:
System is armed System is disarmed
Service mode is enabled System is in programming mode
Vehicle and system statuses:
III BLUETOOTH DEVICES – displays current number and state of recorded
Bluetooth radio tags and radio relays.
VI CONTROL BUTTONS – this panel is used to control a system using but-
tons. To activate or deactivate a function, press and hold the button for more
than 3 seconds (this behavior is implemented to prevent accidentally button
presses.
Control buttons
Arm/Disarm buttons Engine preheater control button
Time channel control buttons Trunk control button
PANIC mode button Service mode button
Update current state button
Note! you cAN chANGe buttoN lAyout IN the “mAIN meNu – settINGs –
coNtRol buttoNs”.
1Doors
2Front hood
3Trunk
Ignition
Shock sensor
Tilt sensor
Motion sensor
Additional sensor
START
ENGINE
I
1 1
1
2 3
1
MAIN MENU
II VEHICLE
III BLUETTOH DEVICES
IV CONTROL BUTTONS
Brake pedal
Engine is running
Siren sound notification state
Interior/engine temperature
HANDS FREE function state
On-board voltage
Fuel level
Outside temperature
I

1716 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
CONTROL OVER THE SYSTEM
Arming
To arm the system when the ignition is off, use one of the methods described
below. The system will confirm the command receiving with 1 short sound sig-
nal and 1 flash of turn indicators.
SLAVE mode
This mode allows arming using special analog inputs or digital connections to
a car. To arm the system, shortly press the “Lock” button on an original remote
control or use a sensor/button on a door handle (for cars with an intelligent
access system).
Note! AddItIoNAl settINGs oR coNNectIoNs ARe RequIRed foR thIs mode.
Mobile application
Open the mobile application. When the system is active, press and hold the
button on the control panel until the scale is fully loaded
Radio tag
A radio tag must be in the Bluetooth coverage area. Shortly press the control
button on the tag.
HandsFree mode
Move with a remote tag (or a paired mobile phone) away from your vehicle
Note! AddItIoNAl settINGs ARe RequIRed foR usING the hANdsfRee mode WIth
AmobIle phoNe.
VALET button
Press and hold the VALET button for 3 seconds. The system will be armed in 30
seconds. The LED indicator is lighting red during the countdown.
There is an option in the system settings that allows to arm the system
with disabled sensors (shock/tilt/motion and additional sensors). The setting
“Switch off sensors when arming using VALET button” is available in the Alarm
Studio (“Main settings”– “Sensors settings”)
Disarming
To disarm the system, use one of the methods described below. The system
will confirm the command receiving with 2 short sound signal and 2 flash of
turn indicators.
If there were alarm events during the arming period, siren will sound 4
times and turn signals will flash 4 times.
WARNING! ItIs RecommeNded to use the “ImmobIlIzeR mode” ANd “pRo-
hIbIt dIsARmING WheN the tAG Is AbseNt” fuNctIoN to INcReAse ANtI-theft
pRotectIoN.
SLAVE mode
This mode allows disarming using special analog inputs or digital connections
to a car.
To disarm the system, shortly press the “Unlock” button on an original re-
mote control or use a sensor/button on a door handle (for cars with an intel-
ligent access system).
Note! AddItIoNAl settINGs oR coNNectIoNs ARe RequIRed foR thIs mode..
Doors are locking
System is arming
1 ash
1 ash
1x
SLAVE
HANDS FREE
MOBILE APP
Doors are unlocking
System is disarming
2 ashes
2 ashes
2x
SLAVE
HANDS FREE
MOBILE APP

1918 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Mobile application
Open the mobile application. When the system is active, press and hold the
button on the control panel until the scale is fully loaded.
Radio tag
A radio tag must be in the Bluetooth coverage area. Shortly press the control
button on the tag.
HandsFree mode
Move toward the vehicle with a remote tag (or a paired mobile phone) .
Note! AddItIoNAl settINGs ARe RequIRed foR usING the hANdsfRee mode WIth
AmobIle phoNe.
VALET button
Enter the ”Secret PIN-code” (see the ”Emergency disarming using the VALET
button” section).
SERVICE (VALET) MODE
It is recommended to put the system into the service mode before handing
it to a car service or valet parking. When this mode is switched on, security
system stops interfering with built-in electronics and disables all functions to
ease maintenance or parking.
To enable this mode, switch on the ignition, a radio tag must be in the cov-
erage zone, enter the “Immobilizer PIN-code”(if the “Code immobilizer” func-
tion is implemented) and use one of the methods described below: Switch on/
off the service mode using a phone and the Pandora BT application
• To switch on the service mode, open the mobile application. When the sys-
tem is active, press and hold the button on the control panel until the
scale is fully loaded.
• To switch off the service mode, open the mobile application. When the sys-
tem is active, press and hold the button on the control panel until the
scale is fully loaded.
Note! INoRdeR to chANGe buttoNs locAtIoN oR to Add ANeW buttoN oN the
coNtRol pANel, pRoceed to the “settINGs” -> “ActIoN buttoNs”.
Switch on/off the service mode using a radio tag
• To switch on the service mode, press and hold the button on a radio tag for
3 seconds. Release the button after 3 flashes of the LED of the radio.
• To switch off the service mode, press and hold the button on a radio tag for 3
seconds. Release the button after 3 flashes of the LED of the radio tag
.
• Switch on/off the service mode using an immobilizer button
• To switch on the service mode, enter the “Immobilizer PIN-code” and press
the immobilizer button 10 times within 20 seconds.
• To switch off the service mode, turn on the ignition and enter the “Immo-
bilizer PIN-code”.
Service mode indication
The system will confirm switching on the service mode with: icon in
the mobile application, with a long sound signal of a Beeper and the green LED
indicator when the ignition is turned on.
The system will confirm switching off the service mode with: disappearing
the icon in the mobile application, two long sound signals of a Beeper
and fading the green LED indicator when the ignition is turned on.

2120 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
• ENTER THE SECOND DIGIT • Press the VA-
LET button the number of times, equals to
the second digit. Pauses between presses
should not exceed 1 second. Each pressing
will be confirmed with an orange LED indi-
cator flash. A pause for more than 1 second
and, red LED indicator flash and a short
sound signal of the beeper confirms the in-
put of the second digit. Then you can enter
the next digit.
• ENTER THE THIRD DIGIT • Press the VALET
button the number of times, equals to the
first digit. Pauses between presses should
not exceed 1 second. Each pressing will be
confirmed with an orange LED indicator
flash. A pause for more than 1 second and,
red LED indicator flash and a short sound sig-
nal of the beeper confirms the input of the
first digit. Then you can enter the next digit.
• ENTER THE FOURTH DIGIT • Enter the
fourth digit of the code using VALET button.
Press the button the number of times, equals to the fourth digit. Pauses be-
tween presses should not exceed 1 second. Each pressing will be confirmed
with an orange LED indicator flash. After entering the fourth digit:
• If the PIN-code is correct, the system will be disarmed. It will be confirmed
with the series of red and green flashes of the LED sound signals of the
Beeper, two signals of the siren and two flashes of the light signalization
• If the PIN-cod is incorrect the system will stay in the previous state. New
input can be attempted after 5 seconds. Incorrect PIN-code is indicated with
a long red flash of the LED.
• If the system was disarmed and the ignition was off, it will enter the pro-
gramming mode after correct entering the “Secret PIN-code”. Turn on the
ignition to exit the programming mode.
LED
VALET
Automatic exit from the service mode
The system can automatically exit the service mode when a vehicle start
moving and when an authorization device is in the coverage zone (radio tag,
remote control, mobile device).
Note! NoAddItIoNAl settINGs ARe RequIRed foR thIs fuNctIoN. check If the
“speed” fuNctIoN Is suppoRted foR youR cAR heRe – loAdeR.pANdoRAINfo.com.
CONTROL OVER THE SYSTEM IN CASE OF EMERGENCY
Emergency disarming using the VALET button
In case you cannot disarm the system using a phone or immobilizer tag, the
‘Secret PIN-code’ can be used. The ‘Secret PIN-code’ is written on the owner’s
plastic card under the protective layer. The code must be entered only when
the base unit is powered and the ignition is off. The PIN-code can be entered
using an external or located on the base unit VALET button. The digits input is
indicated by an external or located on the base unit LED indicator.
WARNING! mAke suRe thAt the pRotectIve lAyeR oN the oWNeR’splAstIc
cARd Is INtAct AfteR AN INstAllAtIoN of the system. the plAstIc cARd holds
the “secRet pIN-code”
WARNING! cARefully Remove the pRotectIve lAyeR, do Not use shARp
objects to AvoId dAmAGING of hIddeN INfoRmAtIoN uNdeR the pRotectIve
lAyeR.
Entering the PIN-code:
• ENTER THE FIRST DIGIT • Press the VALET button the number of times, equals
to the first digit. Pauses between presses should not exceed 1 second. Each
pressing will be confirmed with an orange LED indicator flash. A pause for
more than 1 second and, red LED indicator flash and a short sound signal of the
beeper confirms the input of the first digit. Then you can enter the next digit.
2-2-2-2
PIN

2322 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Emergency control of the anti-theft functions
This section describes how to deactivate and activate anti-theft functions
(Immobilizer and Anti-Hi-jack), which use a radio tag, a remote control or
a mobile phone as an owner authorization device, and “Code immobilizer”
function, which uses standard car controls (buttons, levers, pedals) to enter the
Immobilizer PIN-code.
Emergency deactivation of anti-theft function
To temporarily deactivate the Immobilizer or Code immobilizer function
(pin-to-drive), turn on the ignition when the system is disarmed. Enter the
“Secret code” from the owner’s personal card using the VALET button. The
immobilizer functions will be being deactivated by the time the ignition is
turned off.
Emergency activation/deactivation Immobilizer/Code Immobilizer functions
Emergency control of the anti-theft functions is possible only when the
system is disarmed, the ignition is off, service mode is deactivated, a vehicle
battery is charged.
Enter the“Secret PIN-code”or the “Service PIN-code”(default value is 1-1-1-
1) to put the system in programming mode.
Pauses between presses should not
exceed 1 second. Each pressing will be confirmed with an orange LED indicator
flash. The system will confirm entering the 13th level with the red flashes of the
LED and short signals of the Siren/Beeper.
• TO DEACTIVATE THE FUNCTION – The LED indicator will be green after
entering the programming level. The system will wait 10 seconds for entering
the ‘Secret PIN-code’. If the PIN-code is not entered within 10 seconds or the
input is incorrect, the siren will sound one signal, the LED will produce the
series of red and green flashes and the system will return to the programming
menu. Enter the‘Secret PIN-code’that is written on the owner’s plastic card. The
system will confirm deactivating with two sound signals of the siren, a long red
LED flash and two sound signals of the siren. Turn on the ignition and then turn
off to exit programming mode. The function will be deactivated.
• TO ACTIVATE THE FUNCTION -The LED indicator will light red and the Beeper
will sound a long beep after entering the programming level. The system will
wait for action. Press the VALET button once activate the immobilizer function.
The system will confirm enabling with one short sound signal of the Siren/
Beeper and a green LED light. Turn on the ignition and then turn off to exit
programming mode. The function will be activated.
To manage Immobilizer and Anti-
Hi-Jack functions - After entering
programming mode, press the VALET
button 13 times.
To manage Immobilizer and Anti-
Hi-Jack functions - After entering
programming mode, press the VALET
button 15 times.

CAN2-H/CH2
CAN2-L/CH5
WIRING DIAGRAM
8
7
6
5
4
3
2
1
16
14
13
12
11
10
9
(-)
200 mA (-)
200 mA (-)
200 mA (-)
200 mA (-)
200 mA (-)
2A (+)
(+)
200 mA (-)
(-)
(+)
(+)
200 mA (-)
«LED/VALET»
INP6/CH6 – OUT «Beeper»
CAN1-H
CH1/INP1 –
Code immobilizer input
INP5 – Brake pedal input
Ground
«LED/VALET»
CH7 – OUT Turn indicators
CAN1-L
INP4/CH4 – OUT NO blockage
INP2 – Ignition input
INP3/CH3 – Front Hood input
CH8 – OUT Siren
«+12V»
«+12V»
to the original
wiring
Blue
9
Brown/White
10
Orange/Black
11
Yellow/Black
12
Blue/Black
13
Yellow
14
Purple
15
Red
16
White
1
Red/Black
2
Orange/White
3
4
Yellow/White
Gray
5
Green
6
7
White/Blue
Black
8
15
Base unit (view from the top side)
External
button
X2X1
micro-USB
LEDVALET
LED
VALET
Antenna 2.4 GHz
Mini
DXL 0110L v3
WARNING! Do not shield the built-in antennas.
WARNING! Before starting the installation of the
system, select a car model in the ALARM STUDIO
application (CAN-bus protocol).
WARNING! All power circuits of additional devices
that are not powered through base unit of the
system should have their own fuses.
WARNING! The security system does not require
regular maintenance. In case of malfunction it
should be taken to aspecialized service center.
IT IS FORBIDEN to install the system on
a car with normal voltage other than 12V.
IT IS FORBIDEN to bypass original fuses
of a security system in the installation process.
IT IS FORBIDEN to install a security system
with damaged output cables.
MAIN SOCKET
16
15
14
13
10
9
2
1
6
5
8
7
11
3
12
4
CAN2
CAN1
LED/VALET
CH6/INP6
CH1/INP1
CH4/INP4
CH2
CH5
INP5
GND
LED/VALET
CH3/INP3
CH7
INP2
CH8
+12V

2726 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
SYSTEM INSTALLATION
General installation requirements
• Install the base unit only inside car interior.
• Install securely each system’s component, as conditions of the car standard
operation can harm functionality of the alarm system and cause damage to
the car original systems, including the elements of safety in motion.
• The system installation should be performed when the system sockets and
the negative battery terminal are disconnected.
• The base unit power supply should be switched off when connecting to
CAN-bus.
• The system installation can be performed via twisting together or via lead-
tin soldering followed by isolation of a switching place.
• When wiring, pay attention to sections and materials of switched conduc-
tors, if they are different, bring electrochemical potentials to the Mini v3mal
difference. The isolation should not allow for moisture to reach wiring, as
the presence of moisture will increase electrochemical destruction of wires
(this is especially important for the large current circuits).
• Switched connections should be placed as high as it is possible in the cavi-
ties so water condensate will not form drops on the switching location.
• To avoid the destruction of compounds by car vibration, ensure that there is
a bit of free length to the wiring, providing enough sagging.
• Do not allow wiring in places where the wires isolation can be destroyed
by abrasion.
• Electronic system units should be placed sockets down and as high as pos-
sible to avoid condensate reaching electronic components through the
socket.
• When installing base unit, secure it to the car body for correct operation of
in-built shock sensor.
• All unused system wires during the installation must be insulated and se-
cured to prevent accidental touching of a car body or other wires.
Wiring description
Wire 1 (White) — LED/VALET. This wire connects to the red wire of the ex-
ternal VALET button.
Wire 2 (Red-black) 200m (-) INP6/CH6 — Factory setting is Beeper. This
wire connects to the black wire (-) of the sound emitter Beeper. The red wire
of the beeper connects to a reliable conductor with constant voltage of +12V.
Wire 3 (Orange-white) CAN1-H — wire of digital bus CAN1-High. It con-
nects to an appropriate CAN-High wire of a car.
Wire 4 (Yellow-white) 200mA (-) CH2/CAN2-H — wire of digital bus CAN2-
High. It connects to an appropriate CAN2-High wire of a car. This channel can
be assigned as an output, it will not work as a digital bus in this case.
Wire 5 (Gray) 200mA (-) CH1/ INP1 – Factory setting is “Code immobilizer”,
see description in the “Programming the immobilizer PIN-code”section.
Wire №6 (Green) 200mA (-) CH4/ INP4 — Factory setting is “NO blockage”. This
wire is used to control a blocking relay with a normally open logic. This chan-
nel is activated (a relay is closed – blockage is not active) when the system is
disarmed, ignition is switched on and a radio tag is in the coverage zone (im-
mobilizer mode).
Wire 7 (White-blue) (+) INP5 — Factory setting is“Brake pedal”, it is a guard-
ed and controlled zone. This wire connects to a brake pedal switch where +12V
voltage appears when the pedal is pressed (stop lights wire).
Wire 8 (Black) (-) — Ground. This wire must be connected to the ground of
a car. This wire must be connected first during installation.
Wire 9 (Blue) CH3 — LED/VALET. This wire connects to the black wire of the
external VALET button.
Wire 10 (Brown-white) 200mA (-) CH3/INP3 — Factory setting is “Front
hood”, it is a guarded and controlled zone. This wire connects to appropriate
wire that becomes grounded when the front hood opens.
Wire 11 (Orange-black) CAN1-L — wire of digital bus CAN1-Low. It con-

2928 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
nects to an appropriate CAN-High wire of a car..
Wire 12 (Yellow-black) 200mA (-) CH5/CAN2-L — wire of digital bus CAN2-
Low. It connects to an appropriate CAN2-High wire of a car. This channel can be
assigned as an output, it will not work as a digital bus in this case.
Wire 13 (Blue-black) 200mA (-) CH7 — Factory setting is “Turn lights”. This
wire connects to a hazard flashers button of a car.
Wire 14 (Yellow) (+) INP2 — Factory setting is ”Ignition” input, it is a guard-
ed and controlled zone. This wire connects to an appropriate wire where 12V
voltage appears when ignition is switched on. If there is no ignition status in a
CAN-bus, this input must be connected.
Wire 15 (Purple) 2 (+) CH8 — Factory setting is “Siren”. It connects to a
siren control wire (+).
Wire 16 (Red) (+) — power supply of the system “+12V”. It must be con-
nected to a reliable conductor with constant voltage of 12V.
SYSTEM CONFIGURATION AND PROGRAMMING
System settings and parameters can be configured using the Pandora
Alarm Studio or Pandora Specialist application. Some functions can be con-
figured only by the programming menu of the system. It is required to put the
system to programming mode to get access to the settings.
Entering the programming mode
You can enter the programming mode only if the base unit is powered
form USB socket or from an external power supply, the ignition is off, the sys-
tem is disarmed and the service mode is switched off.
Enter the programming mode by entering the ‘Service PIN-code’ (factory
preset is 1-1-1-1). The PIN-code should be entered using an external or located
on the base unit VALET button. The input is indicated by flashes of an external
or located on the base unit LED indicator.
The system stops to perform control commands while it is in the program-
ming mode.
Note! see the “coNtRol oveR the system IN cAse of emeRGeNcy” sectIoN foR
descRIptIoN of the pIN-code eNteRING pRoceduRe.
Note! IftheRe Is No ‘seRvIce pIN-code’, you cAN eNteR the pRoGRAmmING mode
usING the ‘secRet pIN-code’ WRItteN oN the oWNeR’scARd
WARNING! ItIs pRohIbIted to eRAse the pRotectIve lAyeR oN the oWNeR’scARd.
the INfoRmAtIoN oN the cARd Is INteNded oNly foR the oWNeR of the system.
Exiting the programming mode
There are several ways to exit the programming mode:
Switch on the ignition
Press and hold theVALET button more than 10 seconds (until a siren sound)
Disconnect power of the base unit (disconnect the main power supply and USB)
The system will reboot programmatically (all changes will be saved) after
exiting programming mode. All ways to exit the programming menu are ac-
companied by sound signals of the siren and light signals of the LED indicator.
The signals indicate the number of recorded control devices

3130 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Note! see the “INfoRmAtIoN” sectIoN foR descRIptIoN of sIGNAls INdIcAtING the
NumbeR of RecoRded coNtRol devIces
Pandora Alarm Studio
The Pandora Alarm Studio allows configuring the main parameters of the
system, uploading firmware updates, downloading installation guides, making
the “Pandora CLONE” procedure.
In preparation to programming, these stages should be followed:
• Install the Pandora Alarm Studio to a PC with Windows XP/Vista/7/8/10;
• Start the Pandora Alarm Studio;
• Connect the system and PC via a USB cable;
• Enter the programming mode by entering the service PIN-code;
• The application will automatically open the settings window.
It is recommended to update firmware of the base unit before installing
and programming the system (actual version of the firmware you can down-
load from pandorainfo.com or from the Alarm Studio).You can update firmware
using the Alarm Studio application after entering the programming mode:
• Press the“Update software”button and select a type of updating;
• “Load from file”– select previously downloaded firmware on your PC,“Firm-
ware archive” - firmware will be downloaded from a server to the “firm-
wares” folder.
• Select a firmware file and press the“Update” button;
Exit the programming mode after changing the settings or updating firmware.
Note! IfAN updAtING pRocess hAs beeN INteRRupted foR some ReAsoN ANd the
stAtus INdIcAtoR lIGhts Red, you Need to use the “quIck boot mode” to uploAd
fIRmWARe. opeN the AlARm studIo; de-eNeRGIze ANd dIscoNNect the system; pRess
ANd hold the vAlet buttoN locAted oN the bAse uNIt; ReleAse the buttoN Im-
medIAtely AfteR coNNectING the system ANd AcomputeR vIA usb cAble; the system
WIll eNteR the boot mode.
Programming menu
Enter the programming mode, enter the “Service PIN-code” (default value is
1-1-1-1), the system will wait for level input – “Level 0 Entering a level”. Enter
a desired level using the VALET button (see the “Programming levels table”)
to change settings or parameters. . The system will confirm correct input with
red LED flashes and short sound signals of the siren/beeper and proceed to
the desired level.
AN EXAMPLE
• To enter a level (“Level №1…№17”), press (P) the VALET button the number
of times equals to the desired level number (1…17), pauses between press-
es should not exceed 1 second. The system will confirm correct input with
red LED flashes and short sound signals of the siren/beeper and proceed
to the desired level. To enter a sublevel or a cell of sublevel make a pause
for more than 1 second (), then press (P) the VALET button the number of
times equals to the desired sublevel or cell number.
• For quick access to the higher level, press and hold (H) the VALET button.
The siren will sounds tone beeps (up to 10). These sounds means the se-
quence number of a two-digit level number (the first signal – level №10, the
fifth signal – level №50, the tenth signal – level №100). Release the VALET
button immediately after the desired number of signal. To enter an interme-
diate level (Level №11…№17), press the VALET button the number of times
equals to the second digit (1…7) of the desired level number immediately
after releasing the button. The system will confirm correct input with red
LED flashes and short sound signals of the siren/beeper and proceed to the
desired level.

3332 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Programming levels table
Function VALET button
№0 – Entering a level Уровень Удалить Обно-
вить
№1 – Pairing a remote control D030/Watch2 P1H3
№2 – Changing the Service PIN-code P2
№3 – Recording the idle speed (rpm) P3
№4 – Reset to the factory settings P4H4
№10.1.1 – Pairing a radio tag BT760/BT770 H1P1P1H3
№10.1.1 – Pairing a radio tag BT760/BT770 H1P1P2H3
№10.1.1 – Pairing a radio tag BT760/BT770 H1P1P3H3
№10.3.1 – Pairing a door sensor DMS-100 BT H1P3P1H3H5
№10.3.1 – Pairing a door sensor DMS-100 BT H1P3P2H3H5
№10.3.1 – Pairing a door sensor DMS-100 BT H1P3P3H3H5
№10.3.1 – Pairing a door sensor DMS-100 BT H1P3P4H3H5
№10.4.1 – Pairing a radio relay BTR-101 H1P4P1H3H5
№10.4.1 – Pairing a radio relay BTR-101 H1P4P2H3H5
№10.5 – Pairing a mobile phone H1p5
№10.6 – Pairing an engine compartment
module RHM-03BT/PS-331BT/PS-332BT
H1P6H3H5
№10.7 – Pairing an additional device DI-04
or BT-01
H1P7H3H5
№10.8 – Pairing a telemetry module Pandora
Eye Pro / NAV-X
H1P8H3
№10.9 – Pairing a GPS-receiver NAV-035 BT H1P9H3H5
№10.10 – Updating Bluetooth modem rmware H1P10
№10.11 – Pairing an RF module RFM-470 H1P11 H3H5
№11 – Programming and conguring an
“Immobilizer PIN-code”
H1• P1
№13 – Emergency deactivating/activating code
immobilizer function (pin-to-drive)
H1• P3
№15 – Emergency deactivating/activating
authorization devices (immobilizer, anti-hi-jack)
H1• P5
№17 – Programming bypass of an original
immobilizer
H1• P7
№50 – Pairing a mobile phone H5
№100 – Exit the programming menu H10
Control by the VALET button (see the “Level №0 Entering a level”section)
P– press times H– hold for sec.
– 1 sec. pause •– without a pause
Note! the AddItIoNAl devIces thAt ARe INcluded IN the system set hAve beeN
AlReAdy RecoRded IN the system memoRy (see the “system set” sectIoN of the
useR mANuAl).

3534 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Level 1 – Pairing a control device D030/Watch2
Only one control device can be paired on this level.
Prepare to pair a Bluetooth device, turn the device on in accordance with
its manual. The system will be in the remote controls pairing mode for 1 min-
ute. After a minute or immediately after pairing a Bluetooth remote control, the
system will automatically enter the programming level №0.
The LED indicator will show state of the memory cell: Green light means
the cell is empty and the system is ready for pairing; red light means the cell is
occupied, it is required to delete the current device to pair a new one. Press and
hold the VALET button for 3 seconds until the fourth orange flash of the LED to
remove the previously paired device.
An example of pairing a D030 remote control:
• Enter the programing level №1.
• If the LED is green, the system is ready for pairing.
• Press and hold 3 buttons of a remote control (arm/disarm/F) simultaneously
for 1 second (until a short beep), then release the buttons.
• If pairing was successful, the LED will be red, the siren/beeper will sound a
beep. The system will enter the programming level №0.
An example of pairing a Watch2:
• Enter the programing level №1.
• If the LED is green, the system is ready for pairing.
• Go to the MENU -> Settings -> Bluetooth -> Car -> Pair in the Watch2 menu
and wait for pairing.
• If pairing was successful, the LED will be red, the siren/beeper will sound a
beep. The system will enter the programming level №0.
Level 2 – Changing the factory preset of the service PIN-code
Prepare a new value of the ‘Service PIN-code’, it should consist of 4 digits
(from 1 to 9). Write down or remember the new PIN-code.
The system will enter‘Changing the Service PIN-code’mode and the status
LED indicator will turn off after entering the level.
Changing the ‘Service PIN-code’:
• Enter the first digit of the code using the VALET button. Press the button a
number of times, equals to the first digit. Pauses between presses should
not exceed 1 second, every pressing will confirm with an orange LED indica-
tor flash. A pause for more than 1 second and red LED indicator confirms the
input of the first digit. Then you can enter the next digit;
• Enter the other numbers in the same manner. The input of the fourth num-
ber will be confirmed by the series of red and green LED indicator flashes.
The system will wait for PIN-code re-entering;
• Enter all four digits again;
• If you were able to correctly enter the ‘Service PIN-code’twice, the indicator
will produce the series of red and green flashes, the new PIN-code will be
recorded, the system will return to programming mode.
• In case of the incorrect code input the indicator will be lit red, the system
will return to the programming mode.
Level 3 – Recording the idle speed (rpm) to the system memory
To timely turn off the starter during automatic or remote engine start via
digital or analog tachometer input and the correct operation of the ‘Smart
Turbo Timer’, it is necessary to record the engine idle speed.
Switch on the ignition and start the engine after entering this level of pro-
gramming (the engine should be warmed-up; idle speed should match the sta-
ble idle speed of the warmed-up engine). The system will confirm the presence
of the idle speed status with green flashes of the LED indicator. Wait until the
stable idle speed will be reached and save the changes by pressing the VALET
button. Successful recording of the idle speed will be confirmed with the series
of red and green flashes of LED indicator and a siren signal. The series of siren
signals will indicate incorrect recording. The system will exit the programming
menu and reboot after saving the idle speed.
Level 4 – Resetting to the factory settings
The procedure recovers the factory settings of the system without deleting
previously registered devices (remote controls, tags, mobile device, relays, etc.)
that is stored in the non-volatile memory.
Press and hold the VALET button for more than 4 seconds until a siren sig-
nal, then release the button. The system will confirm resetting to the factory
settings with a long red flash of the LED indicator. After that the system will
return to the programming mode.

3736 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Level 10 – Manage Bluetooth devices/Updating Bluetooth
modem rmware
This level is used to pair/remove/update additional devices and to update
Bluetooth modem of the system.
AteNtIoN! All fuNctIoNs of thIs level ARe AvAIlAble IN the pANdoRA
specIAlIst App WIthout eNteRING the level №10. Goto the “AdvANced
mouNtING” -> “system devIces” to pAIR/delete ANd updAte AddItIoNAl
devIces. Goto the “AdvANced mouNtING” -> “check updAtes” to updAte
system fIRmWARe.
MANAGE BLUETOOTH DEVICE
Each device is paired at a sublevel. To pair devices of the same type, a sub-
level is divided into cells. To enter a sublevel or a cell of sublevel make a pause
for more than 1 second (), then press (P) the VALET button the number of
times equals to the desired sublevel or cell number.
Each sublevel or cell displays its current state by a color of the LED: green
light means the system is ready for pairing, red light means a device has been
already paired and it is required to delete it for pairing a new device. To delete
a device, press and hold the VALET button for 3 seconds (4 orange flashes of
the LED). The system will be in pairing mode for 1 minute. After a minute or
immediately after pairing a device, the system will automatically enter the pro-
gramming level №0
An example of pairing radio tags BT760/BT770:
• Enter the programing level №10.1.1…3.
• If the LED is green, the system is ready for pairing.
• Press the control button on a tag and hold it for 6 seconds (6 flashes of the
tag status indicator), release the button after the sixth flash.
• If pairing was successful, the LED will light red and the siren/beeper will
sound a beep. The system will enter the programming level №0.
An example of pairing door sensor DMS-100 BT:
• Enter the programing level №10.3.1…4.
• If the LED is green, the system is ready for pairing.
• Open the plastic case of the sensor carefully and insert a battery into the
sensor.
• If pairing was successful, the LED will light red and еру siren/beeper will
sound a beep. The system will enter the programming level №0.
An example of pairing a radio module RHM-03 BT:
• Connect the wire 4 (Green) to wire 5 (Black). Connect them to ground (-).
• Enter the programing level №10.6 – “Pairing an engine compartment mod-
ule”. The LED will light green or red
• Connect the wire 7 (Red) to +12V.
• If pairing was successful, the LED will light red and a siren/beeper of the
base unit will sound a beep. The system will automatically enter the pro-
gramming level №0.
• Disconnect the wire 4 (Green) from the wire 5 and insulate all unused wires.
An example of pairing a radio relay BTR-101:
• Connect the wire 1 (GROUND) to a grounded spot of a car.
• Enter the programing level №10.4.1 or №10.4.2.
• If the LED is green, the system is ready for pairing*.
• Connect the wire 3 (PROGRAMMING) to wire 4 (+12V POWER SUPPLY). Con-
nect them to +12V.
• If pairing was successful, the LED will light red and the siren/beeper will
sound a beep. The system will enter the programming level №0.
• Disconnect the wire 3 (PROGRAMMING) from the wire 4 and insulate all un-
used wires. Connect the wire 4 to the ignition (+12V when ignition is on).
UPDATING FIRMWARE OF THE BUILTIN BLUETOOTH MODEM/UPDATING FIRM
WARE OF AN ADDITIONAL DEVICE
To update firmware of the built-in Bluetooth modem, enter the “Level №10’”
“Sublevel 10”. To update firmware of an additional device, enter the “Level
№10”“Sublevel” or “Cell” corresponding to an additional device. The LED will
light red after entering. Press and hold (H) the VALET button for 6 seconds.
Open the Pandora Specialist, go to“Search device”screen and select the device
and then select one of the update option:
INTERNET – It allows you to upload firmware from a server.
FILE MANAGER – This function is available only for Android devices. It allows
you to upload firmware from phone storage.

3938 USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Level 11 – Programming the“Immobilizer PIN-code”
The level is divided into 3 sublevels (Sublevel 11.1 – Selecting buttons; sublev-
el 11.2 entering the PIN-code; sublevel 11.3 – confirmation of the PIN-code input).
The system will automatically enter the sublevel 11.1 (Selecting buttons)
after entering the level 11. The VALET button is used to proceed to the next
sublevels and to save the“Immobilizer PIN-code”
• 11.1 - Selecting buttons
The system will wait for pressing buttons after entering this sublevel. Each
pressing of an active button will be indicated by an orange flash of the LED. You
can turn on the ignition on this sublevel, the system will not exit the program-
ming mode (some buttons are active only when ignition is on). The system can
determine active buttons via a digital bus of a car or via a ‘Code Immobilizer’
analog input.
• 11.2 - Entering the PIN-code
This sublevel is used to program the immobilizer deactivation PIN-code us-
ing the selected buttons. The code can consist of one or more memory cells,
each memory cell can store a sequence of pressing each of the five selected
immobilizer buttons.
The code is entered by pressing the selected buttons for at least 1 second.
Each pressing is confirmed with an orange flash of the LED. A pause for more
than 1 second and the red LED confirms the input for the current memory cell,
you can start entering the next memory cell.
• 11.3 - Confirmation of the PIN-code input
Confirm the entered PIN-code on this level. Repeat the procedure de-
scribed above. The system will compare two inputs after that.
- The system will confirm the correct PIN-code with red and green flashes
of the LED indicator and will memorize the PIN-code, and then the system will
proceed to the programming mode awaiting level input.
- Incorrect confirmation is indicated with a long red flash of the LED indica-
tor, the system will cancel the input and return to the programming mode.
Level 13/15 – Emergency deactivating/activating
authorization devices/functions
Note! see the detAIled descRIptIoN IN the “coNtRol oveR the system IN
cAse of emeRGeNcy” sectIoN of the useR mANuAl.
Level 50 – Pairing a mobile phone
Note! see the detAIled descRIptIoN IN the “mobIle ApplIcAtIoNs” sectIoN
of the useR mANuAl.
Level 100 – Exit the programming menu
To exit the programming menu, press and hold theVALET button for more than
10 seconds until the tenth sound signal of the Siren/Beeper or until a red flash
of the LED. The system will exit programming mode and will reboot program-
matically.