babcockdavis eleGRIL BGE38H User manual

©2023 Babcock-Davis
Rev 04/23
Installation, Operation
+ Maintenance Manual
1
Great Products. Better Partners.
Babcock-Davis is a leader in roof hatches, smoke vents and safety railings for the commercial roofing market. We also manufacture architectural
access and safety-related building products for commercial structures. Babcock-Davis provides local connections through a broad distribution
network to accelerate and simplify the building process for contractors and building owners, offering hassle-free services including access to
technical experts, REVIT tools for BIM, HPDs for LEED v4, 3-part specifications and AIA-accredited continuing education courses.
eleGRIL Stainless Steel Grille
Level Bed, Mechanically Fastened
Models: BGE38H, BGE58H, BGE98H. Frames: BFE38HLBM, BFE58HLBM,
BFE98HLBM
eleGRIL Stainless Steel Entrance Grilles are elegant and durable.
This grille is most often used in high traffic venues as they stand
up to extremely heavy pedestrian and rolling traffic. The eleGRIL
system provides scraping functionality and can be used in
zones 1 - 3.
Introduction + Safety
Please read the complete instructions carefully before beginning any work. To ensure proper
installation and performance of the product, the following actions must be completed by the
installing contractor. Failure to do so will affect product warranty.
Transportation + Storage
oInspect all shipments and materials for missing or damaged components and
hardware.
oMaterial must be stored in a clean, dry location.
Preparation
•Locate the packing slip(s) and/or shop drawings.
•Verify that all products listed on the packing slip are included in the package.
•Check the products for damage. If products are damaged, report a freight claim
immediately and leave the products in their packaging. If you sign for products
without reporting damage you waive your right to a freight claim and will be
responsible for their replacement cost.
•Read the instructions thoroughly before beginning installation.
•Stainless Steel grilles are not recommended for exterior applications that experience
cold, wintery climates. Snow and metal grilles typically lead to slippery, walking
surfaces.
GENERAL SAFETY PRECAUTIONS Improper selection, installation, or use can cause personal injury or property damage.
It is solely the responsibility of the user, through their own analysis, to select products suitable to the specific application
requirements, ensure proper maintenance and use as intended. Follow local, state, and federal regulations for proper
installation and operation requirements.

©2023 Babcock-Davis
Rev 04/23
Installation & Operation + Maintenance
eleGRIL Level Bed, Mechanically Fastened
Models: BGE38H, BGE58H, BGE98H. Frames: BFE38HLBM, BFE58HLBM, BFE98HLBM
2
Great Products. Better Partners.
Babcock-Davis is a leader in roof hatches, smoke vents and safety railings for the commercial roofing market. We also manufacture architectural
access and safety-related building products for commercial structures. Babcock-Davis provides local connections through a broad distribution
network to accelerate and simplify the building process for contractors and building owners, offering hassle-free services including access to
technical experts, REVIT tools for BIM, HPDs for LEED v4, 3-part specifications and AIA-accredited continuing education courses.
Tool List
•Drill/Driver
•Hammer Drill
•Drill Bits, 1/4", 3/8”, for concrete/masonry
•Wrench, size as needed (for anchors)
•Screwdriver bit, size as needed (for anchors)
•Level
•Pry bar
•Screwdriver, flat head
•Caulk
•Masking tape
INSTALLATION
INSTALL THE FRAME (DRILLED FRAMES for MECHANICAL FASTENING)
A flat recess and accurately installed frames are critical to the overall performance of the
grille. Utilize a self-leveling compound (provided by others) if necessary to ensure a level
recess.
1. Determine the correct depth of the recess. The outside of the frame must be flush
with the finished floor surface. Make the recess the appropriate depth and slightly
longer and wider than the frames to allow room to maneuver.
2. Position the pre-cut and mitered frame members in the opening.
3. Mark the pre-drilled fastening point locations on the floor. Drill 1/4-inch diameter by
1-1/2 inch deep holes in the floor for the anchors.
4. Line the frame members up with the holes and securely fasten the frame to the floor
with the provided anchors.
5. Verify the frame to make sure that it is plumb, that corner conditions are joined at the
correct angles, and that it is at the correct height. Also, check the measurements of
the frame against the shop drawings in several locations to make sure that the sizes
are correct. The grille will not fit if the frame is not installed as indicated on the shop
drawings.
6. Pour cement mortar around the outside edges of the frame to be level with the
unfinished floor and the center in sufficient quantity to be level with the inside lip of
the frame. Utilize a self-leveling compound (by others) if necessary to ensure a level
recess. The floor must be flat and level with 1/8 inch over 10 feet to ensure proper
installation.
7. If applicable, lay the pan sections on the bottom of the recess and caulk all seams.
(All caulking to be provided by others.) Make any drain or trap connections.

©2023 Babcock-Davis
Rev 04/23
Installation & Operation + Maintenance
eleGRIL Level Bed, Mechanically Fastened
Models: BGE38H, BGE58H, BGE98H. Frames: BFE38HLBM, BFE58HLBM, BFE98HLBM
3
Great Products. Better Partners.
Babcock-Davis is a leader in roof hatches, smoke vents and safety railings for the commercial roofing market. We also manufacture architectural
access and safety-related building products for commercial structures. Babcock-Davis provides local connections through a broad distribution
network to accelerate and simplify the building process for contractors and building owners, offering hassle-free services including access to
technical experts, REVIT tools for BIM, HPDs for LEED v4, 3-part specifications and AIA-accredited continuing education courses.
(All drain accessories provided by others.)
8. When the cement has hardened, install plywood or other material in the recess to
protect the edges of the frame until it is time to install the grilles. Wait to install the
grilles until the building is ready for use.
INSTALL THE GRILLE
1. Remove the plywood or other filler from the recess and clean the recess thoroughly.
Note that debris will cause irregularities in the recess that will in turn cause the grille
to rock or create a tripping hazard.
2. Refer to the shop drawings and the marks on the sections to determine the correct
location of each section. Note that the grille sections are not interchangeable.
3. Refer to the following hold-down illustration below while assembling hold-downs.
Place the stainless-steel
screws in all hold-downs on
the grille sections. Use the
plastic washers provided to
hold the screws in the lock-
downs before putting the
grilles into the recess.
DO NOT attempt to put the
lock-down screws in by prying
apart the surface wires and
installing from the top of the
grille. This will cause irreversible damage that is not covered by the warranty.
4. Placement of Hold Down Clips
First install clips at each corner of each grille section. Clips should be placed
approximately 4 inches to 6 inches in from each side. Continue placing clips uniformly
along the perimeter and throughout the entire grate section. Clips should be spaced
evenly from 18 inches to 24 inches apart.
5. Installation of Hold Down Clips
Place the clip in the frame at an angle and use a pry bar to insert the clip into the
frame. (See Figure 1). Press/Tap the clip into place using a flat head screwdriver so the
fingers of the clips snap into the space between the surface wires. (See Figure 2).

©2023 Babcock-Davis
Rev 04/23
Installation & Operation + Maintenance
eleGRIL Level Bed, Mechanically Fastened
Models: BGE38H, BGE58H, BGE98H. Frames: BFE38HLBM, BFE58HLBM, BFE98HLBM
4
Great Products. Better Partners.
Babcock-Davis is a leader in roof hatches, smoke vents and safety railings for the commercial roofing market. We also manufacture architectural
access and safety-related building products for commercial structures. Babcock-Davis provides local connections through a broad distribution
network to accelerate and simplify the building process for contractors and building owners, offering hassle-free services including access to
technical experts, REVIT tools for BIM, HPDs for LEED v4, 3-part specifications and AIA-accredited continuing education courses.
Figure 1 Figure 2
6. Place the grille sections in position within the recess. Refer to the shop drawings for
the proper location of the sections. Mark the locations of lock-down holes in the
concrete pit.
7. Remove the grating and set aside.
8. Prepare Concrete for Anchors
Use a hammer drill with a 3/8” concrete bit. First, mark the bit at 5/8” with masking
tape so as not to drill too deep. Drill hole 5/8” deep. The anchor should bottom out
and still sit above the surface.
9. Clear the hole of all debris.
10. Insert the anchor into the hole.
Set the anchor into the clean hole, it should bottom out with a portion of the anchor
sitting above the surface. The setting tool will allow you to hammer the anchor into
the opening and set it on the wedge. The anchor will now sit flush with the surface for
ease of staring the screw.
11. Set the grille sections back into the recess and start threading all hold-down screws in
the embedded anchors. Adjust the grilles to create an even clearance around the
edges and tighten all screws. Do not over-tighten the screws. There should still be
some play in the hold-downs.
12. Save the installation and maintenance instructions and include them with the
closeout documentation for the owner and maintenance personnel.

©2023 Babcock-Davis
Rev 04/23
Installation & Operation + Maintenance
eleGRIL Level Bed, Mechanically Fastened
Models: BGE38H, BGE58H, BGE98H. Frames: BFE38HLBM, BFE58HLBM, BFE98HLBM
5
Great Products. Better Partners.
Babcock-Davis is a leader in roof hatches, smoke vents and safety railings for the commercial roofing market. We also manufacture architectural
access and safety-related building products for commercial structures. Babcock-Davis provides local connections through a broad distribution
network to accelerate and simplify the building process for contractors and building owners, offering hassle-free services including access to
technical experts, REVIT tools for BIM, HPDs for LEED v4, 3-part specifications and AIA-accredited continuing education courses.
OTHER MOUNTING OPTIONS
EZ Loc Surface Block Hidden Slotted Tab
1. Cuts should be made using a grinder with a new wafer wheel. CGW 6 x .045 x 7/8 is
recommended. Take particular care to deburr ends of bars and supports after cutting.
2. Set sections into place being sure that all wires and supports align. Mark all surface
fastener locations on the surface for each section.
3. Remove sections and drill all fastener holes at marked locations in base and install
lead anchors to bed.
4. Place grates back into their locations and fasten down using the flathead machine screws
supplied with grating. Start each screw in its location and once engaged snug all fasteners
tightly starting from the center and working outwards in a circular manner. Repeat for all
sections.
MAINTENANCE
Continued maintenance is critical to the long-term safety and performance of the grille.
Remove the grille and clean the recess periodically to prevent the surface from becoming
uneven. Debris build-up within the recess could lead to deflection in the grille and may
possibly cause tripping hazards. Gloves are recommended when handling the grilles to protect
against sharp edges.
•General cleaning can be done from the surface with a vacuum and brush to remove
debris between the bars.
•Surface wires can be cleaned with a non-ferrous cleaner such as 3M’s Scotch Brite™.
•Do not use steel wool or abrasive pads. The steel in these products will embed in the
wires and subsequently rust.
QUESTIONS?
For more information on installation, repair, or replacement, please contact Customer &
Sales Support at 888-412-3726 or visit babcockdavis.com