Baby Brezza One Step BRZ0069 User manual

Instructions
PLEASE NOTE: All bottles, pump parts & accessories must be empty, clean and rinsed
before use in this sterilizer-dryer
Customer Service
If you are experiencing problems with your BabyBrezza product,
visit babybrezza.com/pages/international to locate your local customer service representative.
Distributed in Australia
by CNP Brands
82 Maribyrnong Street,
Footscray, VIC, 3011
Customer Service 1300 667 137
E: [e-mail]
W: www.cnpbrands.com.au
Distributed in New Zealand
by Wainhouse Distribution
2-6 Argyle St. Morningside,
PO Box 41-014
St Lukes, Auckland, New Zealand
Customer Service 0800 567 5000
E: [email protected]o.nz
Limited 1-Year Warranty
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
The limited warranty is valid only on products bought through authorized resellers. Buying through
an unauthorized reseller.
This warranty is available to consumers only. You are a consumer if you own a Baby Brezza product
that was purchased at retail for personal, family or household use. Except as otherwise required
under applicable state law, this warranty is not available to retailers or other commercial purchasers
or owners. We warrant that your Baby Brezza product will be free of defects in material or
workmanship under normal home use for one year from the date of original purchase. Customer
will be required to present original proof of purchase in order to obtain the warranty benefits. In
the event that you do not have proof of purchase date, the purchase date for purposes of this
warranty will be the date of manufacture. If your Baby Brezza product should prove to be
defective within the warranty period, we will repair it or, if we consider it necessary, replace it.
To obtain warranty services, please contact Customer Service.
©2021 Baby Brezza Enterprises LLC babybrezza.com

IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS
1
Sterilizer Dryer Parts
Lid
Tongs
Control Panel
2
Filter Components
Upper
Basket
HEPA
Filter
Filter
Cover
Screw
Accessory
Tray
Bottle
Posts
Lower
Basket
Sterilizer
Base
Dry Only
Button
Sterilize Only
Button
No Water Indicator Timer
On/O
Button
Automatic
Sterilize/Dry
Button
Remove screw &
lift filter cover
to change filter
We recommend changing the filter
every 3 months.
Check babybrezza.com
for replacement filters and parts
In addition, instructions are also available in an alternative format such as on a website or on request from the user
in a format such as a DVD or For an electronic copy of this manual, please contract our after sales support centre.
TECHNICAL DATA
Supply voltage: 220-240V ~ 50-60Hz Power: 750W
Model: BRZ0069/BRZ0069EU
This marking indicates that products should not be disposed of with other household wastes. To prevent
possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your used device, please use the return and
collection systems or Contact the retailer where the product was purchased. They can take this product for
environmentally safe recycling.
When using electrical appliances, basic safety precautions should always be followed, including the following:
1. Read all instructions carefully before using your sterilizer.
2. Ensure that the supply voltage marked on the appliance corresponds with your power supply.
3. If there is any visible damage to the appliance, the plug or to the supply cord, disconnect the appliance immediately and
do not use it.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in
order to avoid a hazard.
5. Do not allow children to touch or use the appliance. The appliance becomes very hot and the steam can cause severe scalding.
6. Do not move the appliance when it is in use or contains hot liquids.
7. Do not touch the hot surfaces.
8. Do not place the appliance on or near hot surfaces, in a heated oven or near a gas or electric heater.
9. Unplug the appliance from the power supply before cleaning or storage.
10. Do not immerse the supply cord, plug or base unit in water or any other liquid.
11. This Sterilizer base does not contain any user serviceable parts inside. Do not dismantle.
12. This appliance is for indoor household use only. Do not use outdoors.
13. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety.
14. a) Short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.
b) Extension cords are available and may be used if care is exercised in their use.
c) If an extension cord is used: The marked electrical rating of the extension cord should be at least as great as the electrical
rating of the appliance; The longer cord should be arranged so that it will not drape over the countertop or tabletop where
it can be tripped over, snagged, or pulled on unintentionally (especially by children).
15. Children should be supervised to ensure that they do not play with the appliance. User maintenance shall not be made by
children with supervision.
16. Not for space heating purpose.
17. Always use on a level heat resistant surface.
18. Always keep the electric sterilizer and its plug out of reach of small children.
19. To disconnect, turn any control “o”, then remove plug from wall outlet.
20. Ensure water has been added to the base unit before the sterilization cycle is switched on.
21. Always add 165ml of distilled water before use. If you put too little or too much water into the sterilizer, the sterilization
eciency may not be reached.
22. Always unplug from the electric outlet when not in use. Allow to cool before putting on or taking o any parts.
23. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any
manner. Return appliance to the nearest authorized service facility for examination, repair, or adjustment.
24. The use of accessory attachments is not recommended by the appliance manufacturer as this may cause injuries.
25. This sterilizer is intended to be used in household and similar application such as a. sta kitchen areas in shops, oces and
other working environments. b. farm houses. c. by clients in hotels, motels and other
residential type of environments. d. bed and breakfast.
26. Do not open while in use as this product contains boiling water. Beware of escaping steam from the vent holes in the lid.
27. Allow at least 30 minutes interval between operations and make sure the unit has been cooled down before pressing the
start button for sequential use.
28. Steam escaping from the unit can cause burns. Always allow 5 minutes to cool down after the cycle finishes before lifting
the lid.
29. To provide continued protection against risk of electric shock, connect to properly grounded outlets only.
30. CAUTION: Risk of electric shock, disconnect electric power before servicing.
31. Use only distilled water, bottled water or fresh running water to sterilize.
32. Never use any additives.
33. Do not let cord hang over edge of table or counter or touch hot surface.
34. Except cleaning , any other servicing should be performed by an authorized service representative.
35. After heating or all the water is removed from the sterilizer base, the heater surface is subject to residual heat after use.
36. This appliance can be used by children aged from 8 years and above and reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision or instruction concerning used of the appliance in a
safe way and understand the hazards involved.
37. Avoid spillage on the connector.
38. The appliance potential injury from misuse. Such as putting liquid that other
than water to the sterilizer base.
39. This appliance not intended for food or infant formula warming and cooking.

Set-up and Use
43
1. Place the appliance on a flat surface where it is out of reach of children
and it will not be knocked or moved during operation.
2. Remove the lid, baskets and accessory rack from the sterilizer base.
3. Pour water on the base/heater surface to MAX line (165ml/5.5oz).
Never fill past MAX line. We recommend using distilled water to avoid
mineral scale build-up on the heating plate. However, you can use bottled
water or tap water but you may need to descale more frequently.
4. Place the lower basket on the base.
5. Place clean bottles with their opening facing downward on the bottle posts
6. Place the accessory tray in the lower basket (tray not for use with tall bottles).
7. Place bottle accessories on the accessory rack (nipples, collars, caps, etc)
8. Place the upper basket on top of the lower basket, ensuring that it fits
securely without any gaps.
9. Place breast pump parts or more accessories in the upper basket.
10. Press the On/O button once and the function icons will light up.
Choose your desired function following the instructions below.
If there is no selection of function after pressing on/o button, the
appliance will automatically switch o.
Automatic Sterilize/Dry Function:
1. Choose the drying time (after steam sterilization): Press the Sterilize/Dry
button 1 time for 30 minute dry time, 2 times for 45 minute dry time,
3 times for 60 minute dry time. The sterilize/dry cycle will start 3 seconds
after the last button press.
2. When the sterilization cycle starts, the timer will count up second-by-second
for the duration of the sterilization cycle.
3. When the sterilization cycle is complete, the appliance will beep, pause for
3 seconds and begin the drying cycle for the amount of time selected in
step 1. The timer on the timer will count down second-by-second until it
reaches 00:00.
4. When the drying cycle is completed, the appliance will beep 5 times and
switch o automatically.
Before placing items in the appliance for sterilization it is important that
All bottles, pump parts and accessories must be EMPTY, CLEAN & FULLY
RINSED BEFORE USE in this sterilizer dryer
Cleaning
- Always unplug your product before cleaning.
- Do not immerse the base, the supply cord or the plug in water or other liquids.
- Do not clean base under water tap.
- Use a soft damp cloth to clean the base and control console.
- Never use abrasive pads to clean the plastic parts of the machine.
- The lid, accessory rack can be cleaned in hot soapy water.
- Mineral residue, particularly in hard water areas, may deposit on the
heating plate after a few sterilization cycles. To avoid scale build up, wipe
the surfaces with a soft moist cloth after each operation.
- Deposits can be removed with scale removers or by leaving 60ml/2oz
water and vinegar solution (50/50 water & vinegar mix) on the heating
plate for approximately 30 minutes. The plate should then be wiped clean with
a clean, dry cloth. Some discoloration spots may remain after cleaning with a
vinegar solution, but these are harmless.
- Do not use abrasives or solvents for cleaning; they may damage the appliance
and the surface of the heating plate.
Sterilize only function:
1. Press the Sterilize button one time, the timer will display “00:00” and the
steam icon. The sterilization cycle will start 3 seconds after pressing the
sterilize button and the timer will count up second-by-second for the duration
of the sterilization cycle.
2. When the sterilization cycle is complete, the appliance will beep 5 times
and switch o automatically.
Dryer only function:
1. Press the Dry button 1 time for 30 minute dry time, 2 times for 45 minute
dry time, 3 times for 60 minute dry time. The drying cycle will start 3 seconds
after the last button is pressed and the timer on the timer will count down
second-by second until it reaches 00:00.
2. When the drying cycle is completed, the appliance will beep 5 times and
switch o automatically.
Caution: If it is necessary to remove water from the base,
always POUR AWAY FROM FAN OPENING.
Note water pour direction icon on base,
and pour in direction of arrow.

If you can not remedy problems by using the troubleshooting chart above,
visit babybrezza.com/pages/international to locate your local customer service representative.
1. Place the appliance on a flat surface where it is out of reach of children
and it will not be knocked or moved during operation.
2. Remove the lid, baskets and accessory rack from the sterilizer base.
3. Pour water on the base/heater surface to MAX line (165ml/5.5oz).
Never fill past MAX line. We recommend using distilled water to avoid
mineral scale build-up on the heating plate. However, you can use bottled
water or tap water but you may need to descale more frequently.
4. Place the lower basket on the base.
5. Place clean bottles with their opening facing downward on the bottle posts
6. Place the accessory tray in the lower basket (tray not for use with tall bottles).
7. Place bottle accessories on the accessory rack (nipples, collars, caps, etc)
8. Place the upper basket on top of the lower basket, ensuring that it fits
securely without any gaps.
9. Place breast pump parts or more accessories in the upper basket.
10. Press the On/O button once and the function icons will light up.
Choose your desired function following the instructions below.
If there is no selection of function after pressing on/o button, the
appliance will automatically switch o.
Automatic Sterilize/Dry Function:
1. Choose the drying time (after steam sterilization): Press the Sterilize/Dry
button 1 time for 30 minute dry time, 2 times for 45 minute dry time,
3 times for 60 minute dry time. The sterilize/dry cycle will start 3 seconds
after the last button press.
2. When the sterilization cycle starts, the timer will count up second-by-second
for the duration of the sterilization cycle.
3. When the sterilization cycle is complete, the appliance will beep, pause for
3 seconds and begin the drying cycle for the amount of time selected in
step 1. The timer on the timer will count down second-by-second until it
reaches 00:00.
4. When the drying cycle is completed, the appliance will beep 5 times and
switch o automatically.
Troubleshooting
56
Modular set-up options
Upper & Lower Baskets
WITHOUT Accessory Tray
For use with tall bottles,
and accessories.
Upper Basket only
WITHOUT Accessory Tray
For use with accessories
pacifiers and small items.
The tongs can be inserted and stored in the
upper basket or the accessory tray.
When the tongs are clicked into place,
they can be used to lift the basket or tray.
Gently squeeze the tongs to remove them.
They can also be used to grasp parts and
bottle nipples in the sterilizer.
Breast pump parts and any other items safe for
steam sterilization can be placed in the lower or
upper baskets. Try dierent configurations to find
what set-up works best for you.
TIP: For best drying performance, Do not overload
the Sterilizer Dryer.
Upper & Lower Baskets
With Accessory Tray
For use with short bottles,
accessories & pump parts.
Lower Basket only
With Accessory Tray
For use with short bottles,
accessories & pump parts.
Using the included tongs
or
Condition Possible Cause Remedy
Appliance will
not start.
Unit is unplugged.
Unit is not turned on.
Insucient water is in heater
plate area.
Add 165ml (5.5oz) water to heater
plate area.
Make sure the plug is securely
inserted into the power outlet.
Press On/O switch before
choosing function.
Clean heater plate after each use
and use distilled water.
Scaling on
water tank
heater plate.
Items not dry
after drying cycle.
Water is collecting on recessed or
indented areas of items placed
in sterilizer.
Mineral rich water used
persistently.
Make sure to fill to max line, at
least 165m (5.5oz) water to
heater plate area.
TImer stops during
sterilize cycle. “No
Water Indicator” on.
Not enough water added to heater
plate area.
Make sure parts are placed so they
they do not collect water.
Drying cycle selected not long
enough to suciently dry items
in sterilizer.
Select longer drying time.