BABY DELIGHT SNUGGLE NEST User manual

Please read the following instructions and warnings carefully.
Keep this instruction manual for future reference.
Tools required (for wall mouting Camera only): Screwdriver and Drill (not included)
For technical support see back page.
Adult use only.
Adult assembly required. Keep small parts
away from children when assembling.
WARNING:
Warnings & Guidelines:
INSTRUCTION MANUAL
®
®
STRANGULATION HAZARD - Keep cord
out of baby’s reach. NEVER place Camera
or cords within 3 feet of the crib. Use enclosed Security Clips to help secure
cord away from baby’s reach. Never use extension cords with AC Adapters.
Only use the AC Adapters provided. Do not remove this tag.
WARNING:
1

Warnings & Guidelines • Continued
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION.
• STRANGULATION HAZARD - Keep cord out of baby’s reach.
NEVER place camera or cords within 3 feet of the crib. Use enclosed Security
Clips to help secure cord away from baby’s reach. Never use extension cords
with AC adapters. Only use the AC adapters provided.
• When an AC adapter is plugged into an electrical outlet, do not touch the
exposed end.
• Test monitor before first use, periodically, and when changing location of
the Camera.
• Do not use monitor near water (such as bathtub, sink, etc.).
• Keep monitor away from heat sources (such as stoves, radiators, etc.).
• Make sure there is proper ventilation around all monitor components. Do
not place on sofas, cushions, beds, etc. which may block ventilation.
• Nursery monitors use public airwaves to transmit signals. This monitor may
pick up signals from other monitors or similar devices and signals broadcast
by this monitor may be picked up by other receivers.
• This product is not a toy. Do not allow children to play with it.
• This product contains small parts. Adult assembly required. Exercise care
when unpacking and assembling the product.
WARNING:
• Use only the original rechargeable batteries provided. Please contact Baby
Delight, Inc. for replacement batteries. Contact information can be found
on bottom of these instructions or on the battery itself.
• Do not mix old and new batteries.
• Do not mix alkaline, standard, or rechargeable batteries.
• Batteries are to be inserted with correct polarity.
• Clean battery and product contacts prior to battery installation.
• Do not short-circuit supply terminals.
• Only the recommended batteries or equivalent are to be used, volts
and size.
• Remove the batteries when product is stored for long periods of time or
when batteries are exhausted.
• Dispose of exhausted batteries properly.
• Do not recharge non-rechargeable batteries.
• Rechargeable batteries are only to be charged under adult supervision.
• Keep all batteries away from children.
BATTERY WARNING:
2

• 6 Cable Clips
• 1 Anchor and Wall Mount Screw
• 1 Camera, 1 Monitor, 1 Movement Unit
• 2 AC Adapters
Features • Camera
®
®
3
Camera
AC Adapters
Monitor
Lens Microphone
Movement Unit Charging Station
(Place Movement Unit in this to charge)
AC Adapter Jack
Power On LED Power On/Off
Movement
Unit
All Components
X6X1X1
Hardware

®
Features • Monitor
4
Sound/Lights
Power LED
LED Battery Indicator
Power On/Off
Video On/Off
Adjustable
Kickstand
Battery
Compartment
AC Adapter
Plug
Power Button
(Underneath)
Magnetic Clip for
Clothing
Volume
Toggle Left/Right
OK/Select/ZoomTalk Back
Brightness
Toggle Up/Down
Speaker Microphone
Menu
Pause Alarm
®

5
Camera Setup • Adult Assembly Required
1
2Plug AC
Adapter with
Camera Icon
into Camera
Place Camera in
desired location.
2
Pre-drill a hole in
the wall using 3/16”,
4.8mm, drill bit.
(Drill bit and drill not
included).
There is no need to pair any of
the components. The Camera,
Monitor and Movement Unit
have all been synched at
the factory. If for any reason
pairing is lost, please refer to
TROUBLESHOOTING section
on page 9.
mount at
least
3ft
from
crib
IMPORTANT
1TABLE TOP: Place Camera in desired location, plug
in AC Adapter to Camera and turn on.
CAMERA PLACEMENT : ON FLAT SURFACE
WARNING: 3 FT
at least
3ft
from crib
IMPORTANT
PLUG IN
Determine a location for the Camera that will
provide the best view of your baby in the crib. Place
the Camera on a flat surface, such as a dresser,
bureau or shelf. NEVER place Camera or cords within
3 feet of the crib. Be sure to test reception and
Camera positioning.
Be sure to
test reception
and camera
positioning.
CAMERA PLACEMENT: IF WALL MOUNTING

3Tighten screw until only 1/4” (6.3mm)
of the screw is exposed (screw driver
not included). ¼”
®
ON
6
Be sure to test your Monitor’s reception before initial use.
We also recommend testing your Monitor’s reception periodically.
PLEASE KEEP IN MIND THAT THE MOVEMENT & POSITIONING VIDEO
MONITOR WILL NOT PROVIDE THE SAME LEVEL OF PICTURE QUALITY AS
YOUR TELEVISION WITH CABLE, SATELLITE DISH, OR DIGITAL SERVICE.
Monitor Setup • Adult Assembly Required
Movement Unit Setup • Adult Assembly Required
Plug Monitor AC Adapter into
Monitor and hold the power button
on top of Monitor for 5 seconds.
The Movement Unit will transmit movement info and baby’s orientation (side,
stomach and back) to the Camera. The Camera will transmit this information to
the Monitor and display that information on the screen. For best results, make
sure the Movement Unit is within 30 feet of the Camera.
5Secure the cord to
the wall using the 6
Security Clips included
to keep cord away from
baby’s reach. Be sure to
test reception
and Camera
positioning.
at least
3ft IMPORTANT
PLUG IN
4

®
®
100%
®
2
1
ATTACHING MOVEMENT UNIT: Place the top of the
Movement Unit with logo facing UP over baby’s
clothing and then slip the magnetic bottom unit
behind the clothing with the magnets
away from baby.
The two pieces should
connect together with the
clothing in the middle.
7
Press the power button on the center top of the Movement Unit for 4
seconds to power on. You should see movement info and orientation of
the baby (side, back, stomach) on the monitor screen.
Research shows that sleeping
on their back is the safest
position for babies.
Press power on the
movement unit until you
hear a beep.
SIDE
STOMACH
BACK
NOTE: FOR BEST RESULTS, THE WEARABLE UNIT SHOULD BE PLACED ON A
SNUG-FITTING ONESIE ON THE CENTER OF THE BABY’S CHEST.
The Movement Unit will flash every 10 seconds:
Green: Full Battery
Amber: Charge Soon
Red: Low Battery - Charge Immediately
Movement &
Positioning Data
Max 30 FeetMax 600 Feet
®

To Disable the Movement & Orientation Information
Screen will display TURN MOVEMENT
INFO AND ALARM OFF. Use the LEFT/
RIGHT button to select ON or OFF and
press OK.
Disabled Icon – This means the user has disabled the Movement
Unit. You can choose NOT to show the movement info and position
info on the Monitor screen. This also disables all alarms on the
Monitor. The Movement Unit will still alarm if no movement is
detected for 15 seconds.
Low
Battery
Charging No
Signal
Disable
®
100%
OFF
®
100%
Turn Movement
Info and Alarm
ON OFF
menu left/right
ok ok
8
To disable the movement and orientation information from being displayed on
the screen, use the following steps. PLEASE NOTE: This also disables all alarms on
the Monitor.
Low Battery Icon – This means the Movement Unit needs to be
charged. The Movement Unit will flash a red light. The Movement
Unit can be re–charged on the Camera (takes approximately
6 hours) in the dock. The Movement Unit has a battery life of
approximately 96 hours of continuous use.
Low
Battery
Charging No
Signal
Disable
No Signal Icon – This means the Movement Unit is out of range
or powered off while not charging in the dock. Please locate the
Movement Unit and place it in the charging dock on the Camera or
move the Movement Unit closer to the Camera.
Low
Battery
Charging
No
Signal
Disable
Press the Menu button on the Monitor.
Locate the Monitor icon and use
the RIGHT button to move to the
DISPLAY ICON and press OK.
Movement Unit Icon Status • On Monitor Screen
Charging Icon – This means the Movement Unit is currently in
the recharging dock in the Camera and is charging. Movement &
orientation information is disabled. The Movement Unit will flash
an amber or red light every 4 seconds while charging. When fully
charged the light will turn green.
Low
Battery
Charging
No
Signal
Disable

9
Troubleshooting
The Camera, Monitor and Movement Unit have all been paired at the factory.
If any of the components need to be re-paired, please see below:
If the Camera is disconnected from the power source while Movement Unit is in
charging station, please power OFF the Movement Unit to avoid an alarm.
To Re-Pair the Camera and Monitor:
®
1Place the Monitor
and Camera within 3
feet of each other and
power on both units.
3ft
®
100%
menu left/right
ok
2
Pause Icon – Pressing the Pause
button on the Monitor when the Alarm
Icon is on the screen and the Monitor
is alarming will silence the Alarm for
15 seconds. After 15 seconds, if there is
still no movement detected, the alarm
will resume. Note: The alarm can also
be paused if there is any movement
of the Movement Unit.
Alarm Icon – After no movement has
been detected for 15 seconds, the
Monitor will begin to beep. After 20
seconds of no movement detected,
the Alarm icon will appear on the
Monitor screen and the Monitor will
beep rapidly.
®
PRESS PAUSE BUTTON
AND CHECK MOVEMENT
®
Paused
100%
pause alarm
beep
®
100%
Pairing
3You should see the PAIRING
SCREEN that will appear for
20 seconds.
Press the MENU button on the
Monitor and use the RIGHT or
LEFT button to move to the CAMERA
icon. Press the OK button to start pairing.

®
100%
®
®
10
OFF
To Re-Pair the Movement Unit and Camera:
®
100%
®
100%
4
1
5
2
With the Camera powered ON,
press the CODE button on the
bottom of the Camera.
Place Monitor and
Movement Unit within
3 feet of each other.
Power off the Movement
Unit (hold the POWER
button for 4 seconds)
and power on the
Camera.
Press the MENU button on the Monitor and
use the RIGHT or LEFT button to move to
the Movement Unit icon.
You should see live video on
the Monitor.
left/rightmenu
code
button
®
100%
Pairing
Pairing
3 4
Press the OK button and you
should see the PAIRING SCREEN
that will appear for 20 seconds.
Power the Movement Unit on
(hold the POWER button for 3
seconds). You should see movement
and orientation information on
the Monitor.
ON
ok

11
Limited Warranty
At Baby Delight, Inc. we make innovative and high quality products for babies,
children and their parents. We warrant this product to be free from defects in
material and workmanship existing at the time of manufacture for a period of
one year from the date of initial purchase (sales receipt is required for proof of
purchase). If such a defect is discovered during the limited warranty period, we
will, at our sole option, repair or replace your product at no cost to you.
This limited warranty does not cover claims resulting from misuse, failure to
follow the instructions on installation, maintenance and use, abuse, alteration,
involvement in an accident, and normal wear and tear.
For warranty service or replacement part information:
USA: Please call 1-401-333-6800, or write to Consumer Services, 30 Martin St.
Cumberland, RI 02864
Some replacement parts may be available for purchase after this limited warranty
expires. Please visit us at www.babydelight.com or call us at 1-401-333-6800
for details.

Macari Baby, Inc. 401-333-6800
30 Martin Street, Cumberland, RI 02864
www.babydelight.com
[e-mail]
MADE IN CHINA
BD04020, BD0401012