Babyco Walk 'n Rock BW9388 User manual

Infant Walker and Electronic Play Tray
Owner’s Manual
Read all instrucons before assembly and use of the walker.
Keep instrucons for future use.
The child may be hurt if you do not follow these instrucons.
IMPORTANT! KEEP FOR FUTURE REFERENCE.
WARNING! TO BE ASSEMBLED BY AN ADULT!
For BW9388 follow assembly W1005DA2
Walk ‘n Rock
Baby walker with Rocker

1
D. Large spoiler
Check that you have all the parts for this model BEFORE assembling your product.
No tools required.
Parts List
F. Padded seat
B. 2 rear fix wheels
E. Baby walker frame
C. 6 safe rubbers
A. 2 wheels
G. Electronic play tray
B
• Before using, check that the product and all of its components have not been
damaged during transportation. Check regularly that the product is not broken
or damaged. If the product is broken or damaged, keep out of reach of children.
• The product must only be assembled by an adult. For the correct assembly of
the product, please refer to the following instructions.
STAIR HAZARD: Avoid senious injury or death.
Block stairs/step securely before using walker even
when using parking brake.
• Only use the baby walker frame on flat and stable surfaces.
• Never leave child unattended. Always keep child in view while in walker.
The child will be able to reach further and move rapidly
when in the walking frame.
Prevent access to stairs, steps and uneven surfaces,
slopes or unstable floors, swimming pools or other sources of water.
• Guard all fires, heating and cooking appliances.
• Remove hot liquids, electrical flexes and other potential hazards from reach.
• Prevent collisions with glass in doors, windows and fumiture.
• Do not use the baby walking frame if any components are broken or missing.
• This baby walking frame should be used only for short periods of time(e.g.20min).
• This baby walking frame is intended to be used by children who can sit unaided,
approximately from 6 months. It is not intended for children weighing more than 12Kg.
• Do not use replacement parts other than those approved by the manufacturer or
distributor.
Read the instructions carefully before use and keep them for future reference.
The child may be hurt if you do not follow these instructions.
Before using, remove and dispose of any plastic bags and other packaging(e. g
fasteners, fixing ties, etc.) and keep them out of reach of children.

2
Assembling Procedures
3. Fix the safe rubbers in the appropriate housings. Ensure that the safe rubbers are firmly pushed all
the way into the housing on the down base of the walker.
Step 1
Step 2
Step 3
1. Turn the baby walker frame upside down. Fix the wheels in the appropriate housings. Ensure that
the wheels are firmly pushed all the way into the housing on the down base of the walker.
2. Fix the rear fix wheels in the appropriate housings. Ensure that the wheels are firmly pushed all the
way into the housing on the down base of the walker.
Front Side
Back Side

3
Step 4
Step 6
Step 5
4. Open the baby walker frame in the in-use posion, ensuring that all wheels touch the floor. Slowly
raise the tray by polling it in an upward direcon, unl a click indicates that the frame has been
locked correctly in one of the three posions.
5. Insert the plasc rings of the padded seat in the slots located along the upper edge of the walker
frame. Pass the rings through the slots and tug them unl they clear the passage, then release them,
ensuring that they are correctly locked in the posion and cannot recede into the slot.
6. Fit the large spoiler on the rear walker frame; simply place it on the housings, located at the rear of
the backrest, and push it firmly in a downward direcon, ensuring that it has been fied in the correct
posion. Please do not li up baby walker with large spoiler. It is dangerous do in this way.

4
9. Completely assembled.
Step 8
Step 9
Step 7
7. Insert all small toy parts into corresponding holes, then press and hold the front of the toy tray safe
buons, while the toy tray to put on the dinner plate, release the buon, then the toy tray is locked.
B
8. Place the hooks on to the tube at the corresponding posion to fix the foot rest well when in
rocking funcon.

When opening, closing or adjusng the walker, ensure that your child is at a safe
distance. Before placing the child in the walker ensure that the secondary lock
buon is correctly locked again.
How to Adjust the Height of Baby Walker Frame
10. To adjust the seat’s height, remove the child from the baby walking frame, pull up the safe buon
located under the small tray table and rotate it to 90 degrees. keep the safe buon pressed, then
raise or lower the small table unl the desired posion is reached, then pull up the safe buon and
rotate it to 90 degrees again to lock the small table.(If it is a automac secondary lock, please make
sure the lock rotated to 90 degrees.)
Step 11
Step 10
The front
press
90 degree
rotation
90 degrees
rotation
How to Convert Walker to Rocker
11. Use two hands to press the buons on the two sides and turn over the two side boards 90 degrees,
then will changed to be rocking funcon.

6
Step 13
The walker includes one electronic play tray that aaches to the walker frame as
shown in step 7. The funcon and use of the play tray are shown here.
Using Electronic Play Toy Tray
Step 12
90 degree
rotation
90 degrees
rotation
A
B
C
D
E
F
G
H
Rotate 360 degree to hear click sound.
Turn le to hear startup sound of the car.
Lights up when song starts.
Hear a honk when press down.
Turn 360 degree to hear humorous tune.
Press to hear songs.
Switch to adjust volume, turn on and off .
Push forward to hear throle sound.
B
AB
ED
GH
FC
12. Firstly, pull down the buon under top tray, make sure the buon finally parallel to the adjusted-de-
vice(see 1st picture). Meanwhile, press up the front poson(see 2nd picture), and press down the top
base ll the end. The frame folds up completely.
The front
press
How to Fold the Walker

7
• Check regularly the walker frame for signs of damage or wear.
• Clean the plasc parts, including the stoppers, with a damp cloth.
• Clean the seat with brush or family soap and neutral scour
• Dry the metal parts to prevent the formaon of rust.
• Prolonged exposure to direct sunlight may cause the fabric to fade.
Product Care and Maintenance
Fing and / or Replacing Baeries
The toy of the walker frame requires 2X"AA" 1.5Volt alkaline
type baeries(not included).
• Baeries must only be fied by an adult.
• To fit and/ or replace baeries: loosen the screw on the baery
compartment cover with a suitable screwdriver, press the
tab and remove the baery compartment cover. Then remove
the spent baeries and fit new ones, ensuring that they have
been fied in the correct polarity, as shown inside the baery
compartment. Replace the baery cover and ghten the screw.
• Always keep baeries and tools out of reach of children.
• Always remove spent baeries from the toy to avoid the danger
of possible leakage from the baery damaging the product.
• Always remove the baeries if the toy will not be used for
a long period.
• Only use alkaline baeries of the same type of equivalent to the
type recommended for the correct funcon of this product.
• Never mix new and old baeries, or different types of baeries.
• Do not burn or dispose of spent baeries into the environment.
Dispose of spent baeries at an appropriate differenated
collecon point.
• Do not short-circuit the baery terminals.
• Do not aempt to recharge non-rechargeable baeries: they
might explode.
• The use of rechargeable baeries is not recommended and
cannot be used.