BaByliss PRO FX59ZE User manual

FX59ZE
PROFESSIONAL CORDLESS TRIMMER
TONDEUSE DE FINITION PROFESSIONNELLE SANS FIL
LITHIUM POLYMER

7
PROFESSIONAL
CORDLESS TRIMMER
FX59ZE
This heavy-duty trimmer features
zero gap stainless steel T-blades,
great for detailing, designs and
all other ne work. Very easy-to-
handle, it is also perfect for fading
beards, sideburns and the nec-
kline. A powerful DC motor and
lithium polymer batteries deliver
high performance for clean, close
cutting.
OPERATING INSTRUCTIONS
• Before using the trimmer for
the rst time, charge conti-
nuously for 2 hours. Maximum
battery capacity will only be
reached after 3 charging and
discharging cycles.
• Make sure the switch on the trim-
mer is in the “0-OFF” position.
Connect the charging jack into
the receptacle on the buttom
of the trimmer. Plug the adapter
into any electrical outlet (at the
voltage listed on the label axed
to the adapter). The charging
indicator will light up to indicate
that the charging has begun.
Charging is complete after 1 hour.
User will see all 4 bars lit on the
trimmer handle when nished.
• The adapter may become warm
while charging. This is normal.
• Preserving the batteries: in order
to maintain the optimum capa-
city of the rechargeable batteries,
the trimmer should be recharged
for 2 hours approximately every 6
months.
• Turn the switch to “HI” for high-
speed function and “LO” for low-
speed function.
• Make sure the switch on the trim-
mer is in the “0-OFF” position
when the trimmer is not opera-
ting.
MAINTENANCE INSTRUCTIONS
VERY IMPORTANT: Blades must
be cleaned and oiled on a regular
basis for proper functioning. Fai-
lure to regularly clean and oil the
blades will void the warranty.
Maintenance of the blades
•
Remove hair trimmings and
debris from the blades using the
provided cleaning brush. Wipe
the housing clean with a dry cloth.
• Apply a few drops of lubricating
oil to the blades, and wipe oany
excess oil with a dry cloth. This
last procedure is important for
the proper maintenance of the
blades.
Always apply oil to the blades be-
fore and after use. This will ensure
maximum cutting performance.
Hold trimmer away from you in a
downward position and apply oil
on the front and sides of the cutter
ENGLISH

8
blade. Wipe excess oil owith a
soft, dry cloth.
Any other servicing should be per-
formed by an authorized service
representative, since the appliance
has no other user serviceable
parts. This product is for professio-
nal use.
Replacement (removal)
of blade set
To remove blade set from your
trimmer, make sure the trimmer is
in the “0-OFF” position. Remove
the blade set by placing thumb
against the smaller cutter and
pushing downward, releasing the
cutter from the trimmer housing.
Replace with new cutting system
and reverse the removal proce-
dure, only this time place your
thumb on the large cutter and
snap into place. Be careful not to
use too much oil and don’t oil your
trimmer more than necessary,
as this could damage the motor
(never attempt to oil the motor
bearing, as it is permanently lubri-
cated).
Blade care
Because the trimmer blades are
precision-made for a very spe-
cial use, they should always be
handled with care and cleaned re-
gularly to ensure maximum perfor-
mance. Each time you nish using
the trimmer, take the cleaning
brush provided and brush away
any loose hair that has collected in
the blades. Use a clean cloth to dry
the attachment, reattach and then
store the trimmer to protect the
blades until the next use.
DO NOT RINSE BLADE OR
TRIMMER HANDLE OR ADAPTER.
Be especially careful when chan-
ging or adjusting the blades. When
you have your trimmer serviced,
be sure both blades are sharpened
or replaced at the same time.
STORAGE: When not in use, your
appliance is easy to store. Allow
appliance to cool, then store in a
safe, dry location. Do not jerk or
strain cord at plug connections.
HOW TO USE COMB
ATTACHMENTS
• To use the comb attachments,
always turn the trimmer to the
“0-OFF” position.
• Slide the comb attachment onto
the front of the trimmer blade
and snap over the back of the
blade.
• To remove, push up the attach-
ment comb at the back of the
blade and remove comb.
ZERO GAP ADJUSTMENT TOOL
IMPORTANT! Only ever attempt
to zero gap the blades using the
adjustment tool, following the ins-
tructions very precisely.
The adjustment tool is required to
adjust the blades to zero gap, to
achieve a closer, more precise cut.

9
Regular
REGULAR
Zero Gap
ZERO GAP
ZERO GAP
Step 1.
Before placing the blade into the
adjustment tool, use the screwdri-
ver provided to loosen the tension
screws, without removing them
completely from the blade holder.
Step 2.
Place the blade into the adjust-
ment tool in the side labelled ‘Zero
Gap’.
Step 3.
Push the blade guide up as far as
the adjustment tool allows, so the
moving blade sits closely with the
top of the adjustment tool. The
blades will now be ush with each
other.
Step 4.
Using the screwdriver, tighten the
tension screws to hold the blade
in place.

10
Step 5.
Remove the blade from the ad-
justment tool by gently pushing
the blade from the opposite side.
REGULAR - Resetting the blade
for regular use
Step 1
Before placing the blade into the
adjustment tool, use the screwdri-
ver provided to loosen the tension
screws, without removing them
completely from the blade holder.
Place the blade into the adjust-
ment tool in the side marked
Regular.
The tool will automatically push
the moving blade down to its
regular position.
Step 2.
Tighten the tension screws to hold
the blade in place.

11
Step 3.
Remove the blade from the adjust-
ment tool by gently pushing the
blade from the opposite side.
CLEANING AND MAINTENANCE
To maintain correct performance,
the blades must be regularly clea-
ned and oiled. They are removable
for easy cleaning.
• With the trimmer facing you,
push the blade up and away from
the trimmer to remove.
• Brush away the hair from the
blades and the interior of the
cutting head with the cleaning
brush.
• It is recommended to oil the
blades every time that the
trimmer is used, using the oil
provided. Never use any other
product: this oil was formulated
for high speed trimmers, it does
not evaporate or slow down the
blades.
• After cleaning click the blade
frame back in place.
DISPOSAL OF LITHIUM
POLYMER BATTERY
The trimmer has lithium polymer
batteries. To protect the environ-
ment, these batteries should be
removed and properly disposed of
when the unit is no longer opera-
ting. To remove the battery block
for disposal or recovery, follow
these instructions:
1. Disconnect the trimmer from the
electrical outlet.
2. Discharge the battery pack com-
pletely before removing.
3. Remove the blade and 5 screws.
NOTE: one screw is located un-
der the rating label.
4. Open cover.
5. Remove the screw that fastens
the printed circuit board to hou-
sing. Lift printed circuit board
out.
6. Unplug lithium-polymer battery
block.
7. To protect the environment, do
not dispose of your battery with
your ordinary household waste.
For more details on recovery of
material and waste-treatment
facilities, please contact the
waste disposal services of your
region.
FEATURES
• Zero gap stainless steel T-blade
• Powerful DC motor
• Cordless operation
• Lithium-polymer batteries
• 4 comb guides 3mm – 6 mm –
10mm – 13mm
• Lightweight, silent, low heat
• Including cleaning brush and
lubricating oil
• Worldwide voltage

EU DECLARATION OF CONFORMITY
DECLARATION DE CONFORMITÉ UE
This declaration of conformity is issued under the sole responsibility of the manufacturer
La présente déclaration de conformité est établie sous la seule responsabilité du fabricant
soussigné
Type of product / Type de produit : Trimmer / Tondeuse
Type number / Numéro de type : T152a
Trademark / Marque : BaByliss / BaByliss PRO / Conair / CPL
With following characteristics
Avec les caractéristiques suivantes : 100-240V~50-60Hz 12VDC 1A
Country of origin / Pays d’origine : Taiwan
The object of the declaration described above is in conformity with the relevant Union
harmonisation legislation:
L’objet de la déclaration décrit ci-dessus est conforme à la législation d’harmonisation de
l’Union applicable:
2014/35/EU Low Voltage Directive / Directive basse tension
2014/30/EU ElectroMagnetic Compatibility Directive / Directive
concernant la compatibilité élec-tromagnétique
2015/863/EC RoHS Directive / Directive RoHS
2009/125/EC Ecodesin Directives implemented by the Commission
Regulations (EC) No. 1275/2008 amended by (EU) No.
801/2013 and (EU) No. 278/2009 (where applicable) /
Directive relative à l’écoconception mise en œuvre par les
règlements de la Commission (CE) No. 1275/2008 modiée
par (UE) No. 801/2013 et (UE) No. 278/2009 (le cas échéant).
2006/42/EC Machinery Directive / Directive Machine
In accordance with the following standards:
En accord avec les normes suivantes:
LVD EN 60335-1 2012 A11: 2014; AC: 2014; A13: 2017
EN 60335-2-8 2015 A1: 2016
(inluding EMF /
y compris EMF) EN 62233 2008
Ecodesign EN 50563 2011 A1: 2013
EMC EN 55014-1 2017
EN 55014-2 2015
EN 61000-3-2 2014
EN 61000-3-3 2013
CE mark rst axed / Date de 1ère apposition du marquage CE: 04/2018
Signed by and on behalf of / Signé par et au nom de:
BABYLISS FACO S.P.R.L. (authorised by / autorisé par BABYLISS S.A.R.L.
and / et Conair Group Ltd)
Avenue de l’Indépendance 25
B-4020 Wandre, Belgium

FAC 2019/02

BabylissPRO®
Green Side Bât. 1B
400 avenue Roumanille – B.P. 20235
F – 06904 SOPHIA ANTIPOLIS cedex
FAC 2019/ 02