babymod 6922 Installation and operating instructions

revised23DEC2014 Page 1
Drawer Dresser (6922) Assembly and Operation Manual
Congratulations on purchasing this product. This product will provide many years of service if you
adhere to the following guidelines for assembly, maintenance, and operation. This product is for resi-
dential use only. Any institutional use is strictly prohibited.
Please be sure to follow the instructions for proper assembly. Use a Phillips head screwdriver for
assembling the product. Do not use power screwdrivers. All of our products are made from natural
woods.
Please understand that natural woods have color variations which are the result of nature and not
defects in workmanship.
DO NOT SUBSTITUTE PARTS. ALL MODELS HAVE THE SAME QUANTITY OF PARTS AND HARD-
WARE. YOUR MODEL MAY LOOK DIFFERENT FROM THE ONE ILLUSTRATED DUE TO STYLIS-
TIC VARIATIONS.

Page 2
PARTS
B. Base Frame
C. Wood Cleat
D-1. Left side panel D-2. Right side panel
A. Leg (4)
E. Top panel
F-1. Back Top Support Rail
F-2. Back Center Support Rail
F-3. Back Bottom Support Rail
F-4. Front Bottom Support Rail
G-1. Top Front Drawer
G-2. Center Front Drawer
G-3. Center Front Drawer
G-4. Bottom Front Drawer
H. Drawer Center Support Rail (4)
I. Drawer Bottom Panel (4)
J. Drawer
Left Side
Panel (4)
K. Drawer
Right Side
Panel (4)
L. Drawer Back Panel (4)
M. Back Panel (2)

HARDWARES
Page 3
O. Cam Bolt (18) P. Cam Lock (18)
Q. 1-1/8” Phillips
Round Head Bolt (4)
R. 1-1/4” Phillips
Round Head Bolt (4)
S. Wood Dowel 10mm (8)
T. Wood Dowel 8mm (15)
U. Wood Dowel 6mm (16)
V. 1-1/4” Wood
screw (18)
W. Small
screw (64)
X. 5/8” Washer
Head screw (2)
STEP 2.
B
C
V
T
STEP 1.
B
A
R
S
N-1. Left Side Glide (4)
N-2. Left Drawer Glide (4)
N-3. Right Side Glide (4)
N-4. Right Drawer Glide (4)
Insert 10mm wood dowels (S) into each leg(A). Attach
four legs to the four corners of base frame (B) using
1-1/4” Phillips round head bolt (R). Tighten the bolts
securely.
Insert 8mm wood dowels (T) into the wood cleat (C).
Then attach the wood cleat (C) to the base frame (B)
as illustrated using 1-1/4” wood screws (V).
Tools Needed
(not included)
Phillips
screwdriver

Page 4
D-1
OP
F-1
F-4
F-3
Screw the cam bolts (O) into the left side panel (D-1)
and cam lock (P) to support rails (F-1, F-3 and F-4)
as illustrated.
STEP 5.
STEP 3.
N-1 N-3
W
D-1 D-2
Attach four left side glides (N-1) to the left panel (D-1)
and four right side glides (N-3) to right panel (D-2)
using small screws (W) as illustrated.
Do not overtighten the screws.
STEP 4.
Insert 8mm wood dowels (T) into both ends of four
support rails (F-1, F-2, F-3 and F-4).
5a
T
T
T
F-2
F-1, F-3, F-4

F-4
F-1
F-2
F-3
D-1
D-2
Repeat the procedures in step 5A and step 5B. Set up
the right side panel (D-2) as the illustration shown.
Attach the support rails (F-1, F-2, F-3 and F-4) to the
left side panel (D-1) as illustrated. Secure the sup-
port rails and left side panel by turning cam locks (P)
clockwise with a Philips screwdriver.
Page 5
STEP 6.
STEP 7.
Side Panel
T
Insert 8mm wood dowels (T) into the top ends of both
side panels as illustrated.
5b

Page 6
O
E
O
Screw four cam bolts (O) into the top panel (E).
STEP 8.
Lightly land the top panel (E) onto the side panel
(D-1, D-2) assembly. Make sure that all the cam
bolts (O) and 8mm wood dowels (T) fit their holes.
Secure the attachment by rotating four cam locks
(P) as illustrated.
STEP 9.
Attach two back panels (M) to the back dresser
using small screws (W) and two 5/8” washer head
screws (X) as illustrated.
E
P
D-2
D-1
STEP 10.
X
M
MW

Page 7
H
U
L
Insert 6mm wood dowels (U) into both ends of each
drawer center support rail (H). And then attach the
drawer center support rail (H) to the drawer back panel
(L) as illustrated.
STEP 12.
Attach the left drawer glide (N-2) to drawer left side
panel (J) and right drawer glide (N-4) to drawer right
side panel (K) using small screws (W).
W
N-2, N-4
Drawer side panels
Secure the side panels (D-1, D-2) to the base frame
(B) using four 1-1/8” Phillips round head bolt (Q).
D-1
B
Q
Lightly land the dresser onto the base frame (B) as
illustrated. Make sure that the 8mm wood doewl (T)
at the wood cleat (C) fit its holes at the front bottom
support rail (F-4).
STEP 11.
D-2
B
11a
11b
12a
12b

STEP 13.
G
O
P
G
I
U
H
Screw two cam bolts (O) into the drawer top
panel (G).
Attach the drawer top panels (G) to the drawer
assembly as the illustration shown. Make sure
that all the cam bolts (O) and 6mm wood dowels
(U) fit their holes.
Secure the attachment by rotating two cam locks
(P) as illustrated.
Pay attention to the center of drawer top panels (G). Make
sure that the two 6mm wood dowels (U) fit their holes.
H
K
L
J
N
P
I
Insert Drawer
Bottom Panel (I)
Slide the drawer bottom panel (I) into the grooves
in the sides and back of the drawer. Be sure it
goes all the way into the groove in the drawer
back.
Attach the two drawer side panels (J and K) and
drawer back panel (L) by screwing 1-1/4” wood
screws (V) into the holes on side panels as the
illustration shown.
V
L
Page 8
12c
12d

Page 9
Repeat the procedures from step 12A to step 13 to
set up the four drawers.
Put the four finished drawers into the dresser and check that they glide smoothly.
STEP 14.

Serious or fatal crushing can occur when furniture tips over on children. To help prevent tip-over, follow the
steps below to install this anti-tipping strap.
FURNITURE ANTI-TIPPING KIT INSTALLATION
WARNING
Place heaviest item in the lowest drawers.
do not set TVs or other heavy objects on
top of this product.
Never allow children to climb or hang on
drawers, doors, or shelves.
Never open more than one drawer at a time.
(OR)
Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is permanent label. Do not attempt to remove!
Unless specifically designed to accommodate,
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
X 2
X 1 X 1
X 1
Stubby
Screwdriver
Phillips
screwdriver
(not included)
Tools Needed
Pencil
Locate a 2” x 4” stud behind the wall, and make a
mark.
15a 15b
Install the strap on the wall with long screw and washer.
2” x 4” wall stud
STEP 15.
Page 10

IMPORTANT: As with all infant and baby furniture, it is important to check fasteners, screws,
and bolts periodically for tightness. Parents should ensure a safe environment for their
children by checking the furniture regularly before placing a child in the product.
Care and Cleaning:
Do not scratch or chip the finish.
Do not use abrasive chemicals for
cleaning. Clean with mild soap on a
soft rag. rinse and dry thoroughly. If
you ever refinish this furniture, be sure
to use only a non-toxic finish specified
for children’s products. If you choose
to refinish this furniture, the warranty
will be voided.
Storage:
Pine woods exchange moisture with the air adjusting
to major changes in room temperature and humidity.
Therefore it is best to place your furniture away from
heating or air-conditioning vents.
Sunlight is not friendly to solid wood furniture and
prolonged direct exposure to harsh sunlight can discolor
the finish. Be careful not to place your furniture in direct
sunlight for extended periods of time.
As with all your fine furniture, blot up spills immediately.
15c
Install the other end of strap on
the back of dresser with short
screw and washer into the wood
framing of the dresser.
Finish
KEEP THIS MANUAL IN A SAFE
PLACE FOR FUTURE REFERENCE.
READ ALL INSTRUCTIONS BEFORE USING THE PRODUCT.
KEEP THE INSTRUCTIONS FOR FUTURE USE.
This item has a manufacturer’s limited one year warranty.
Visit our web site at www.themdbfamily.com for more information.
Page 11