Bacmove HMI5-TP7 User manual

HMI5-TP7
BACMOVE
Firme Web Inc.
HMI5-TP7
BACnet Touch Panel

HMI5-TP7 Revision 0002
Table of Contents
Introduction................................................................................................................................................... 2
Specifications................................................................................................................................................. 2
Initial Setup.................................................................................................................................................... 2
In-Wall Mounting Installation ....................................................................................................................... 3
1. Make the cut-out for the Touch Panel.............................................................................................. 3
2. Install the mounting bracket into the cut-out................................................................................... 3
System Settings ............................................................................................................................................. 3
Network Settings........................................................................................................................................... 4
USB File Transfer ........................................................................................................................................... 5
Web Interface HMI5...................................................................................................................................... 5

HMI5-TP7 Revision 0002
Introduction
The HMI5-TP7 is a 7-inch capacitive BACnet touch screen panel. Its customizable user-interface helps
visualize and control many buildings systems. Thanks to its in-wall flush mount design it integrates into
conference rooms, reception areas, corridors, and apartments.
Specifications
Model
HMI5-TP7
Power supply
9VDC-36VDC, POE IEEE802.3af
Dimension
182 x 121 x 25 mm (L x W x H) (7.17” x 4.77” x 0.98”)
Fixation
In-wall mount
CPU
8-Core ARM Cortex CPU
Wi-Fi
802.11b/g/n
Ethernet interface
1, RJ45 port
Operating System
Android 6.0
Initial Setup
Connect the power and network using one of the following options:
1. Mains Power and Ethernet:
▪Connect the Ethernet cable (cable not included) to your network.
▪Plug the power cable into the touch panel.
2. POE (Power Over Ethernet):
▪Connect the Ethernet cable (cable not included) to a powered port on your network, do not
plug the supplied power cable.
3. Mains Power and Wi-Fi:
▪Plug the power cable into the touch panel, do not plug the Ethernet cable.

HMI5-TP7 Revision 0002
In-Wall Mounting Installation
The visible part of the touch panel in front of the wall measures 182mm (7.1 ″) W x 121mm (4.8 “) H x
15mm (0.6”) D. This bracket can also be used for surface mounting using the 75mm (2.95”) x 75mm
(2.95”) VESA holes.
1. Make the cut-out for the Touch Panel
▪Make a cut-out in the wall 160mm (6.3”) W x 104mm (4”) H x 21mm (0.82”) D, or use the in-wall
bracket as a template.
2. Install the mounting bracket into the cut-out
▪Insert the mounting bracket into the wall cut-out with the flanges at the bottom.
▪Use 4 screws (not supplied) to fix the bracket to the wall.
▪Use the 2 supplied screws to fix the touch panel to the bracket.
System Settings
To access the system settings, use the following JavaScript method from your HMI5 user interface.
JSInterface.setOptionString("START_ACTIVITY_SETTINGS", "1");
This will launch the settings where network and other parameters can be configured. The main setting
screen will stay open for 1 minute. If you navigate to another settings screen, you must press the back
arrow to return to HMI5.

HMI5-TP7 Revision 0002
Network Settings
Configure the network using one of the following options:
1. Ethernet with DHCP: This is the default, so nothing further to do. Note that Ethernet will not
work if Wi-Fi is enabled.
To see the allocated IP address, press "Ethernet" under "Wireless & networks", and the IP
Address is shown.
2. Ethernet with Static IP Address:
▪Press " Ethernet" under " Wireless & networks ".
▪Toggle "Ethernet" to "On".
▪Click "Static IP".
▪Enter the desired network setting.
▪Click "Ok".
3. Wi-Fi with DHCP:
▪Press " Wi-Fi" under "Wireless & networks".
▪Toggle "Wi-Fi" to "On".
▪Click the chosen network and enter the Wi-Fi password.
▪Click "Connect".
To see the allocated IP address, click the three dots at the top right and on “Advanced”.
4. Wi-Fi with Static IP Address:
▪Press " Wi-Fi" under "Wireless & networks".
▪Toggle "Wi-Fi" to "On".
▪Click the chosen network and enter the Wi-Fi password.
▪Tick “Advanced options”.
▪Scroll down and change “IP settings” to “Static”.
▪Enter the desired network settings.
▪Click "Connect".

HMI5-TP7 Revision 0002
USB File Transfer
Connect the touch panel to your computer with a USB 2.0 cable A male to A male.
The touch panel should appear as a USB drive, on the computer.
If the touch panel does not appear or it displays an empty drive follow the following procedure. Press the
option even if it already shows as being configured.
▪Configure “MTP (Media Transfer Protocol)” in the menu “Settings > Developer options > Select
USB Configuration.”
▪Configure “Host Mode” in the menu “Settings > Developer options > USB Mode Change”.
Web Interface HMI5
Thanks to the HMI5 app, any web developer can create within a few minutes an interface to visualize
and control buildings system. HMI5 presents a simple JavaScript interface to access the BACnet network.
Visit the following link for the HMI5 documentation.
https://bacmove.com/bacnet-hmi-hmi5-guide