BADA SYSTEM NO-100 User manual
To reduce the risk of electric shock, do not remove the cover(or back)
No User-serviceable parts are inside. Refer servicing to qualified
service personnel. Throughout he whole manual, pay special attention
to the following marks that indicate hazardous situations.
Notice
Read this manual carefully and make sure you understand the provided
instructions. For your safety, check what the result each action will be.
Warnings
Warnings : Indicates a hazardous situation which, if not
avoided, could result in serious injury.
Caution : Indicates a situation which, if not avoided, could
damage the equipment or apparatus.
Note : Indicates additional information to the user to make
the user aware of possible problems and information of any
importance to help the user to understand, to use and to
maintain the installation.
When this crossed-out wheeled bin symbol is attached to a
product it means that the product is consistent with
European Directive 2002/96/EC. Please inform yourself
about the local separate collection system for electrical and
electronic products.
The logo informs that the receiver is consistent with terms
and conditions of Directive 2004/108/EC concerning
observance by Member States of provisions regulating
electromagnetic compatibility, and to the terms and
conditions of Directives 2006/95/EC concerning observance
by Member States of provisions refulating low voltage
electricity and safety with relation to the handling and
operation of electrical equipment.
This product has been designed, tested and manufactured
according the European CE Directive 2014/53/EC.
1. Notice
1. Notice
FCC Compliance Notice
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
This device complies with part 15 of FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
RF Exposure Information
This equipment complies with radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be co-
located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with
minimum distance 20cm.
To avoid electric-shock hazards, do not open
the housing, refer servicing to qualified
personnel only.
Do not expose the receiver to direct sunlight.
Keep it away from the heat source.
When the abnormal phenomenon occurs you
should cut off the power supply immediately
Switch the receiver off whenever it remains
out of service for an extended period.
Keep the receiver away from flower vases,
tubs, sinks, etc., in order to avoid damaging
the equipment.
Do not block ventilation holes of the receiver
so air can circulate freely.
Do not touch the receiver during thunder,
since that might create electric-shock
hazards. It is recommended to cut off power
supply.
Do not touch the receiver during thunder,
since that might create electric-shock
hazards. It is recommended to cut off power
supply.
2. Safety Instructions and Precautions
OTT STB AC Adapter HDMI Cable
RCU/Battery User Manual
HDMI cable (Type A, high-speed HDMI™ cable, 4K@60Hz
output support), Related equipment such as S/PDIF optical
cables are available in the market.
Precautions for installation : After connecting the cable, connect
the product to power. If the power is turned on during connection
damage to this product may occur.
Battery precautions
If the battery installed in the remote control has reached the end
of its lifespan, replace it with a new one immediately.
Leaving the dead batteries unattended may cause leakage and cause
the remote control to malfunction.
(Especially if you use cheap and poor quality batteries, leakage may
occur. Do not use as it can be severe.)
3. Accessories / Components
Accessories
1. Power LED :
Standby mode: Red / Operation mode: Green
2. IR Sensor
1. DC 12V : Connect the adaptor DC Jack(DC power in).
2. S/PDIF : Connect to AV Amp.(S/PDIF Optical)
3. HDMI OUT : Connect to TV HDMI input.
4. LAN : Connect to Router's LAN port.
4. Description of the OTT / Installation
Front View
Rear View
1. Micro SD: Insert Micro SD storage for TV-record or
Multimedia.
2. USB 3.0 : Connect to USB devices. (USB 3.0 & others)
3. USB 2.0 : Connect to USB devices. (USB 2.0 & others)
※Insert USB storage for TV-record or Multimedia.
4. Description of the OTT / Installation
Side View
Installation : 1. HDMI
VIDEO
AUDIO
LRHDMI
TV(HDMI)
Adapter Amp.(Optical S/PDIF)
WiFi Router
(LAN or WiFi)
1 2
3
4
Installation : 1. HDMI
4. Description of the OTT / Installation
Installation : 2. Network Cable & WiFi
How to connect a network cable for high-speed Internet service.
Connect the receiver's Internet terminal to the WiFi Router(or
home gateway)'s LAN (or ETHERNET) terminal.
Connect the HDMI output terminal of the receiver to the HDMI input
terminal of the TV using an HDMI cable
(Type A, high-speed HDMI® cable, 4K@60Hz output supported).
For details on how to connect to the HDMI input terminal and how
to use it, refer to the TV instruction manual.
Installation : 3. DC Cable (Power)
Connect the adaptor DC jack to the receiver's DC 12V port.
Installation : 4. S/PDIF
Connect to devices that support S/PDIF (Optical) interface, such
as audio amplifiers and AV receivers. S/PDIF cables can be
purchased from the market and used.
Symptom Cause Check Action
When the
HDMI
screen
does not
appear
· Is the power plug
unplugged?
· Are the TV and receiver
connected correctly?
· Is the TV input selection
properly selected?
· Is the screen not displayed
even if the connection is
correct?
· Insert the power plug into
the outlet correctly.
· Connect the TV and
receiver correctly.
· Press the TV/External
input button on the TV to
select the input correctly.
(HDMI input)
· Turn the AC power off
and on again.
5. Troubleshooting
When
there is no
sound
· Isn't it set to mute?
· Is the audio device
connected to the HDMI
output or optical output
cable set to receive the
output signal of this unit?
· Is the HDMI output or
optical output connector
connected?
· Is there no sound even if
all connections are normal?
· Press the mute button to
cancel.
· Select the correct input
mode for the audio device
or TV connected to the
HDMI output or optical
output connector.
· Insert the HDMI output or
optical output connector
correctly.
· Turn the AC power off
and on again.
initial menu
screen does
not appear.
· Does normal initial
screen not appear when
the receiver's power is
turned off and then on?
· Turn the AC power off
and on again.
· Contact customer service.
There is no
software
upgrade.
· Is the internet cable
connected? Are the Wi-Fi
settings and the router
connection normal?
· Turn off the power and try
again, or contact
customer service.
The remote
control does
not work.
· Are the batteries installed
correctly? · Are the
batteries too old?
· Insert the batteries
according to the polarity.
· Replace a new batteries.
When the
power does
not come on
· Is the power plug
unplugged?
· Is the power temporarily
out of power?
· Insert the power plug into
the outlet correctly.
· Operate a light or
household electrical
appliance.
CPU
ARM
Cortex A55, Quad Core 64bit
CPU
Cores
RTD
1319PB (15K DMIPS, REALTEK)
GPU
High
-performance Multicore mailG31-MP2
Storage
8
GB eMMC 5.1
SDRAM
2
GB DDR4 SDRAM
IR
(RCU)
38
KHz Data Receiving , NEC
HDMI
HDMI
2.0aTX with HDCP 2.2, 4K 10bit UHD @60Hz up 4096x2160
Ethernet
RJ
45 10/100M Fast Ethernet interface
Wi
-Fi
IEEE 802. 11b/g/n, 2.4GHz Single band
USB
1
x USB 3.0 port, 1x USB 2.0 port
Ports
HDMI
2.0, USB 2.0, USB 3.0, S/PDIF(Optical/IEC-6095B),
LAN
10/100Mbit, Micro SD (up to 128GB), DC 12V
Software
(OS)
Android
10 (AOSP)
Video
Format
4
:3, 16:9, Letter Box, Pan & Scan
Video
Support
10
bit, Up to 3840x2160@60fps, HDR10 support
Audio
Mode
Stereo/Mono/Left/Right/Exchange
Audio
Decoding
MPEGI&II,
MP3, AAC-LC, HE-AAC V1/2
Input
Voltage
DC
12V/1A
Power
Consumption
Max
12W
Power
Consumption in
St
andby
<
0.5W
Storage
Temperature
-
10~60°C
Operating
temperature
-
0~45°C
Humidity
<
95%
Dimensions
(W x D x H)
126
x122 x32mm
Net
Weight
0
,28 kg
6. Product Specifications
Memo.
www.badasystem.co.kr
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States
and other countries.
Rev.1.1
Table of contents
