BADEN HAUS BELLAGIO Series User manual

Side view for plumbing
Features:
Drawers push-open and soft-close
Handleless ergonomic continous drawer
Includes fully adjustable drawersliders
Fully finished interiors
Includes installation hardware
Micro-Density Fiberboard (MDF) construction
PVC finish resists moisture and scratches
BELLAGIO
Back view for plumbing
18
19
14
11,8
15
Wall
16,2
16,6
16,2
18
19
14
11,8
15
5,5
Wall Wall
5 25.6
9.5
46.5
3.8
19
18 28

BELLAGIO

Installation tools not included:
Installation notes:
Install this product according to the installation guide
Spcial site preparation is required.
Wall bracing and Baden Haus supplied hardware are
recommended.
The plumbing must be roughed into the plumbing
cutout area of the vanity.
Refer to the sink rough-in and the vanity rough-in for
proper placement. The water supply and drain lines
must be installed before installing the vanity.
BELLAGIO
Materials Included:
X8X8
8 nylon rawlplug
8 screws
2 wall plate
X2

BELLAGIO
1
2
3
X
Y
X
Y
Step 3
Place the wall brackets on the finished
wall and install at the locations drilled
with the screws as shown here.
According to measures taken on step 2,
make drills with diameter 0,3in. For each
wall plate must be made 4 holes. Then
insert nylon rawlplug for each drill.
Fix wall plate to wall using screws. After
that plates are strongly fixed on wall, you
can install vanity on wall.
Step 2
Determine the ideal location of your new vanity.
Mark the holes and drill pilot holes in the dry wall.
Step 1
Pull out completely the drawers and take off from
the slide rails.

--
--
++
++
--
++
--
--
++
++
--
++
Step 4
It is possible to adjust the vanity using
the adjusting screws.
Step 5
Fully extend the slide rails out.
Place the drawer into the slide rails.
To secure drawer, close the drawer
until a series of clicks are heard.
4
BELLAGIO

18
41,7
18,3
4,3
1,77
1,37
2,16
18
27,5
18,3
4,3
1,77
1,37
2,16
RESIN BASIN ART. 50212
Top view of sink
BELLAGIO
Sink assembly
Install the faucet to the top and drains to the sink. Refer to the faucet and drain manufacturer’s instructions.
Complete the faucet connections. Run water and check for leaks.
Apply a bead of silicone behind the top surface to the finished wall.
RESIN BASIN ART. 50213
Top view of sink
18
41,7
18,3
4,3
1,77
1,37
2,16
RESIN BASIN ART. 50214
Top view of sink
Installation notes:
Faucet and silicone are not included.
All sizes are subject to tolerance.

RESIN BASIN ART. 50215
Top view of sink
BELLAGIO
Sink assembly
Install the faucet to the top and drains to the sink. Refer to the faucet and drain manufacturer’s instructions.
Complete the faucet connections. Run water and check for leaks.
Apply a bead of silicone behind the top surface to the finished wall.
18,3
18
4,3 2,16
1,37
1,37
1,77
55,5
1,77
2,16
18,3
18
4,3 2,16
1,37
1,37
1,77
69,3
1,77
2,16
RESIN BASIN ART. 50216
Top view of sink
Installation notes:
Faucet and silicone are not included.
All sizes are subject to tolerance.

28
18
SOLID SURFACE TOP ART. 50185
Top view of sink
BELLAGIO
41,8
18
SOLID SURFACE TOP ART. 50186
Top view of sink
55,6
18
SOLID SURFACE TOP ART. 50187
Top view of sink
69,4
18
SOLID SURFACE TOP ART. 50188
Top view of sink
SOLID SURFACE BASIN ART. 50184
5
24,5
12,7
1
WALL
WALL
2
MAX
4/4,7in
MIN
2,7/3,1in
Sink assembly
Install the faucet to the top and drains to the sink. Refer to the faucet and drain manufacturer’s instructions.
Complete the faucet connections. Run water and check for leaks.
Apply a bead of silicone behind the top surface to the finished wall.
Installation notes:
Faucet and silicone are not included.
All sizes are subject to tolerance.

BELLAGIO
28
18
WOODEN TOP ART. 50189
Top view of sink
41,8
18
WOODEN TOP ART. 50190
Top view of sink
55,6
18
WOODEN TOP ART. 50191
Top view of sink
69,4
18
WOODEN TOP ART. 50192
Top view of sink
CERAMIC BASIN ART. 50179
6
23,6
16,5
MAX
3,1in
MIN
2,1in
1
WALL
WALL
2
Sink assembly
Install the faucet to the top and drains to the sink. Refer to the faucet and drain manufacturer’s instructions.
Complete the faucet connections. Run water and check for leaks.
Apply a bead of silicone behind the top surface to the finished wall.
Installation notes:
Faucet and silicone are not included.
All sizes are subject to tolerance.