Badger Basket 765 User manual

MODEL #: 765/766/767/769
NAME: Dressed Bassinet withAdjustable Canopy
TOOLS NEEDED: Hex Head Wrench (included)
Socket Wrench or Adjustable Wrench or Pliers
PARTS INCLUDED:
(A) 1 Bassinet Frame with Bedding & Canopy Attached
(B) 1 Bassinet Bottom Panel
(C) 2 1” Carriage Bolts
(D) 1 Wood Support Bar
(E) 6 1/4” Acorn Nuts
(F) 2 1-1/4” Carriage Bolts
(G) 2 Plastic Legs
ASSEMBLY
INSTRUCTIONS
Adult Assembly Required
Save these instructions for future use
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday through Thursday 7:30 AM to 5:00 PM CST)
[email protected]
PLANT AND GENERAL OFFICE: PO Box 227, Edgar, WI 54426-0227 715-352-2311 Fax: [phone]
CORPORATE OFFICE: 111 Lions Dr., Suite 220, Barrington, IL 60010
Page 1 of 4 1.1/0604
BEFORE YOU
BEGIN ASSEMBLY:
Ensure that all the parts and
hardware listed above are
included. If anything is missing,
please do not return the product
to the store. Call or e-mail us
for assistance.
(H) 2 Washers
(I) 2 Metal Support Rails
(J) 2 2” Hex Head Screws
(K) 1 Hex Head Wrench
(L) 2 1/2” Hex Bolts
(M) 1 Bassinet Sheet
(N) 1 Mattress Pad
C
L
F
J
E
HK
ABD
M, N
G
I
Note: hardware is not shown actual size.

ASSEMBLING THE BASSINET:
STEP1: Insert the BASSINET BOTTOM PANEL (A) into the BASSINET FRAME WITH
BEDDING (B) with the white side of the bottom panel facing up. Insert the TWO 1”
CARRIAGE BOLTS through the BOTTOM PANEL and the fabric and secure to the WOOD
SUPPORT BAR (D) with TWO 1/4” ACORN NUTS (E). Tighten the nuts well, but don’t over-
tighten. See PICTURES 1A and 1B.
STEP 2: At the foot end of the bassinet, insert ONE 1-1/4” CARRIAGE BOLT (F) through the
hole on the metal tube of the BASSINET FRAME (A) and then through the top hole on one
PLASTIC LEG (G). Secure the bolt with ONE WASHER (H) and ONE 1/4” ACORN NUT (E).
Tighten securely but don’t overtighten. See PICTURES 2A and 2B.
STEP 3: Repeat Step 2 for the opposite side of the bassinet (the end where the hood is
attached). Before you tighten the WASHER (H) and ACORN NUT (E) slip the edge of the fabric
hood between the BASSINET FRAME (A) and the PLASTIC LEG (G). See PICTURE 3.
STEP 4: Line up the WOOD SUPPORT BAR (D) with the middle hole on the PLASTIC LEG
(G) (you can do either side of the bassinet first). Take ONE METAL SUPPORT RAIL (I), ONE
2” HEX HEAD SCREW (J), and the HEX HEAD WRENCH (K). Secure wood support bar,
metal support rail, and plastic leg together with the 2” HEX HEAD SCREW (J). See PICTURES
4A and 4B .
STEP 5: Repeat Step 4 on the opposite side of the bassinet with the second metal support rail.
STEP 6: Insert ONE 1/2” HEX BOLT (L) through the METAL SUPPORT RAIL (I) and the
bottom hole on the PLASTIC LEG (G). Secure with ONE 1/4” ACORN NUT (E). See
PICTURE 5.
STEP 7: Repeat Step 6 for the metal support rail on the opposite side.
STEP 8: If not already done, put the BASSINET SHEET (M) onto the MATTRESS PAD (N).
Put the pad with sheet into the bassinet.
Your bassinet is now ready for use! Suitable for use until Baby is 16 lbs (7.27 kg) or until Baby
is able to roll over unassisted and/or push up on hands and knees. The fabric can be spot cleaned
with warm water and a mild detergent if needed.
Page 2 of 4 1.1/0604

Page 3 of 4 1.1/604
PICTURE 1A - Bottom Panel insterted into
Bassinet Frame; 1” bolts inserted through
Bottom Panel.
PICTURE 2A - 1-1/4” Carriage Bolt inserted
through metal tube on Bassinet Frame and
through top hole on Plastic Leg.
PICTURE 2B - 1-1/4” Carriage Bolts secured
with Washer and Acorn Nut.
PICTURE 1B - Wood Support Bar andAcorn
Nuts secured to the 1” Bolts from Picture 1A.
PICTURE 3 - Fabric Hood slipped between Bassi-
net Frame and Plastic Leg before 1-1/4” Carriage
Bolt is secured with Washer & Acorn Nut.
The picture above is an overview of
Steps 4 through 7.

PICTURE 4A - Wood Support Bar, Metal Sup-
port Rail, and Plastic Leg properly positioned. PICTURE 4A- With a 2” Hex Head Screw,
secure the Wood Support Bar, Metal Support
Rail, and Plastic Leg together. For illustration
purposes the screw is not fully inserted in the
picture above. Be sure that you screw
it in completely.
PICTURE 5 - 1/2” Hex Head Bolt inserted
through Metal Support Rail and Plastic Leg.
Secured with anAcorn Nut.
When fully assembled, the bassinet stand should look
like the picture at left and the bassinet should look
like the picture above.
Page 4 of 4 1.1/0604