BAFANG Luna X-1 User manual

04/01/2021 The Unofficial Luna X-1 Enduro Display Manual | An unofficial manual for Luna Cycle’s awesome X-1 Enduro e-bike.
https://bradland.github.io/unofficial-luna-x-1-enduro-display-manual/ 1/6
View on GitHub
The Unofficial Luna X-1 Enduro Display Manual
An unofficial manual for Luna Cycle's awesome X-1 Enduro e-bike.
The Unofficial Luna X-1 Enduro Display Manual
The X-1 comes equipped with Bafang’s M600 drive system. This includes the G521 motor and DP C240 display
& controller.
The Controller
You’ll use the buttons on the controller to navigate the display, change settings, and adjust the configuration.
Display Basics
The display shows information about your e-bike’s settings and riding statistics.
Battery Remaining

04/01/2021 The Unofficial Luna X-1 Enduro Display Manual | An unofficial manual for Luna Cycle’s awesome X-1 Enduro e-bike.
https://bradland.github.io/unofficial-luna-x-1-enduro-display-manual/ 2/6
Displays the remaining capacity of the battery as a percentage value.
Headlight/Backlight Indicator
Press and hold the Up button to toggle the display backlight. The display also features a light sensor that will
automatically trigger the display backlight and headlight (if equipped) when in a dark environment. The
headlight icon will appear when the headlight/backlight is active.
Assist Setting
Press Up to increase the assist level and Down to decrease. Assist levels start at 0 (no assistance) and scale up to
5 (maximum assistance). Note that the Assist Setting affects the maximum power available at 100% throttle. For
maximum power at 100% throttle, select PAS 5.
Boost Mode
5 (maximum assistance)
4
3
2
1 (minimum assistance)
0 (no assistance)
Walking Mode
Boost Mode
Note: Since all versions of the X-1 are equipped with a throttle, this feature is made moot by the ability to simply
press the throttle lever.
Boost mode allows you to exceed the drive’s 25 MPH (40 km/h) PAS limiter. This feature allows the rider to use
full motor power temporarily, bypassing the limit. To initiate boost mode, start by pedaling to 25 MPH. Press Up
repeatedly until the Boost Mode Icon (pictured below) appears. Press and hold the Boost / ON-OFF button. You
should feel the motor assist you beyond 25 MPH. To terminate boost mode, release the Boost / ON-OFF button.
Walking Mode
Repeatedly press Down until the walking mode icon is displayed. Then press and hold Down for 2 seconds and
the motor will move the bike along at a walking pace. To stop, release the Down button.
Note: You do not need to use the throttle while using Walking Mode. Doing so may cause the bike to leap out of
your grip.

04/01/2021 The Unofficial Luna X-1 Enduro Display Manual | An unofficial manual for Luna Cycle’s awesome X-1 Enduro e-bike.
https://bradland.github.io/unofficial-luna-x-1-enduro-display-manual/ 3/6
Info Display
Cycle the info line by briefly pressing the Boost / ON-OFF button. Available information includes:
TRIP (km,mi) - trip distance traveled (can be reset in settings)
ODO (km,mi) - total distance traveled
MAX (km/h,mph) - maximum speed (reset by trip reset)
AVG (km/h,mph) - average speed (reset by trip reset)
RANGE (km,mi) - estimated range remaining
CAL (Kcal) - the rider’s energy consumption (reset when the bike is turned off)
POWER (W,A) - real-time power output
TIME (minutes) - riding time (reset by trip reset)
Adjusting Settings
To enter the settings menu, press and hold the Up and Down buttons at the same time for 3 seconds. The display
will show the main settings menu. Use the Up and Down buttons to select an item, and press the Boost / ON-
OFF button to activate an item.
The menu is arranged in a two-tier heirarchy, with the following items:
Setting
Unit
Auto Off
Brightness
Power View
Al Sensitivity
Trip Reset
Vibration
Service
Assist Mode
Back
Information
Wheel Size
Speed Limit
Display Info
Controller Info
Torque Info
Error Code
Back
Exit
Details for each menu item follow:
Setting

04/01/2021 The Unofficial Luna X-1 Enduro Display Manual | An unofficial manual for Luna Cycle’s awesome X-1 Enduro e-bike.
https://bradland.github.io/unofficial-luna-x-1-enduro-display-manual/ 4/6
These settings can be configured to adjust the operation of your bike.
Unit
Configures the linear unit of measure used for speed, trip, odometer, etc.
Imperial: miles
Metric: kilometers
Auto Off
Configures the time (in minutes) before the system automatically turns off. Can be disabled by selecting OFF
from the menu. Note that the system draws a small amount of power, even when the bike is not moving. It will
slowly deplete your battery if auto off is disabled and the bike is left on.
OFF, 0–9
Brightness
The brightness of the display as a percentage of maximum intensity.
10%, 30%, 50%, 75%, 100%
Power View
Configures the unit used to display the real time power output.
Current: amps
Power: watts
Al Sensitivity
Configures the sensitivity of the light sensor for the backlight / headlight. Note that this is a capital “a” followed
by a lower case “l”, which stands for Auto-Light. The font makes it easily confused with Artificial Intelligence.
Other display firmware versions use all-caps “AL”.
0–5
0 disables the auto-light
1 is the lowest sensitivity
5 is the highest sensitivity
Trip Reset
Resets the trip values. See Info Display section for a list of values reset by this function.
YES, NO
Vibration
Enables a vibration with each press of a controller button.
YES, NO

04/01/2021 The Unofficial Luna X-1 Enduro Display Manual | An unofficial manual for Luna Cycle’s awesome X-1 Enduro e-bike.
https://bradland.github.io/unofficial-luna-x-1-enduro-display-manual/ 5/6
Service
Enables service mode.
YES, NO
Assist Mode
Configures the available number of assistance levels. Note that changing this does not change the amount of
total assistance available. It is best to think of them as divisions of a whole. E.g. 1/3, 2/3, 3/3 for 3 levels of
assist and 1/5, 2/5, 3/5, 4/5, 5/5 for 5 levels of assist.
3, 5, 9
Back
Navigates back to the main menu.
Information
These settings are for information only. They are loaded with the firmware and cannot be changed.
Wheel Size
28 Inch, the size of the wheel used for computing speed.
Speed Limit
90 km/h / 56 MPH, limits the top speed of the bike.
Display Info
Displays the hardware and software version of the display.
Controller Info
Displays the hardware and software version of the controller.
Torque Info
Displays the hardware and software version of the torque sensing unit.
Error Code
Displays a list of the 10 most recent error codes.
Back
Navigates back to the main menu.

04/01/2021 The Unofficial Luna X-1 Enduro Display Manual | An unofficial manual for Luna Cycle’s awesome X-1 Enduro e-bike.
https://bradland.github.io/unofficial-luna-x-1-enduro-display-manual/ 6/6
Exit
Exits the menu system.
The Unofficial Luna X-1 Enduro Display Manual maintained by bradland
Published with GitHub Pages