BAICHUN BC 10 User manual

Quick Start Guide
(FOR REMOTE CONTROL)
14+ EN
BC 10
1) Unfold the arms
2) Power aircraft
Press and hold the power switch until the aircraft’s lights turn on.
3) Pair remote with the aircraft
Turn on the power switch of the remote controller, and the four lights of the aircraft are always on,
that means automatic frequency pairing is successful.
4) Gyroscope calibration
Place the aircraft on a flat horizontal surface, pull down the
left and right sticks of the remote in the direction of and 5
o'clock at the same time (as shown in the picture), the
remote makes a "DI" sound, the aircraft’s lights will flash
quickly during the process , once the lights change back to
the previous lights, the gyroscope calibration is completed.
Switch
Red LED ON
Blue LED ON
Gyroscope calibration

Method 2
ALWAYS REFER TO INSTRUCTION MANUAL FOR COMPLETE DETAILS
5) Unlock engines
Method 1: Push the left joystick to the highest position, when the propellers rotate, the motors are
unlocked successfully.
Method 2: Pull down the left joystick and right joystick at the same time in the direction of 5 o'clock
and 7 o'clock, the propellers will rotate, unlock the motors successfully.
6) Take off the aircraft
Method 1: After unlocking successfully, short press "one key take off" button.
Method 1: After unlocking successfully, push the left joystick to take off.
7) Flight control
* Throttle (Left joystick)
* Rotate left and right(Left joystick)
* Forward and backward(Right joystick)
Method 1
Method 1: One key take off/landing
Method 2

* Fly left and right(Right joystick)
8) Stop the engines
Method 1: Short press "one key landing" button.
Method 2: After doing the unlock gesture, if you want to stop the motor, pull down the left joystick and
the right stick at the same time in 5 and 7 o'clock direction, and the propellers will stop turning.
Method 3: Pull down the left joystick to the lowest position until the propellers stop turning.
Emergency Stop
1. When the tilt angle of the aircraft exceeds 60 degrees, the aircraft will stop rotating;
2. When the propeller is stuck, the motor will stop rotating automatically.
9) Fine tuning adjustment
OTHER FUNCTIONS
！
Method 1: One key take off/landing
Method 2
Method 3
Forward and backward fine-tuning
Side fine-tuning
Backwards
Forwards
Left
Right
Offset backwards, use the
forward fine-tuning button
to correct;
Offset Forwards, use the
backward fine-tuning
button to correct.
Offset right, use the left
fine-tuning button to
correct;
Offset left, use the right
fine-tuning button to
correct.

10) One key to backward
Press this button and hold for 2-3 seconds, the aircraft will retreat along the tail direction. At this time,
when you move the right stick in any direction, the aircraft will stop continuing to retreat.
Attention: This function can only be done backwards, it can’t return to the take-off point and to land
automatically.
11) Headless mode
Short press to enter headless mode, and short press again to exit headless mode.
After entering headless mode, the flight direction of the aircraft will according to the front, rear, left and
right of the remote controller for flying.
Attention: When the aircraft ‘s 4 lights flash quickly that shows a low power status,and the headless
mode can’t be used.
12) 360°rolling
Step 1: Short press the 360° roll button, and the remote control will continue to make the sound of "Di
Di Di";
Step 2: Push the right joystick, the aircraft will roll 360° according to the push direction of the right. For
example, if you want to let the aircraft flip left, just short press the 360° roll button, then push the right
stick to the left.
Attention:
1. The 360° roll function is automatically disabled when the aircraft enters a low voltage state.
2. This function can only be used when the aircraft is higher than 1 meter from the ground.
One key to backward
Headless mode
360° rolling
4

Step 4: Open the APP "WIFI UAV "
WIFI NAME: FLOW-xx-xxxxxx
Step 2: Power aircraft
Step 3 : WIFI connection
Quick Start Guide
(FOR MOBILE CONTROL)
Step 6: Gyroscope calibration
Please click the icon ,if the 4 LED of aircraft flash quickly until the LED become stay on, gyroscope
calibration is successful.
Step 7: One key take off/ to land
Click this icon , the aircraft will fly to a position one meter above the ground automatically.
Click this icon again, the drone will auto to land.
Attention :
If the remote links the drone in advance, even though connect the wifi and view the fpv, the app's one key
take off and landing can not be used, just for take photo and video since app controlling and remote
controlling seperates.
*Other functions
Step 5: Pair APP with the aircraft
After opening the APP, the APP will automatically link to the aircraft within 3-5 seconds and the
aircraft lights will turn on.
Attention: If the drone linked with the app in advance, the remote won't link with the drone any
more ;
At this time, if you want to use the remote to control the drone ,
please exit the app and disconnect the drone's WIFI firstly, then pair the remote controller with the
drone only.
Step 1: Open WIFI setting ,and search the WIFI name start at FLOW*****, and connect it.
Step 2: Launch the APP until you can view the application's real time video.
Do not recommend beginners to control the aircraft with the APP
Scan QR code below using your device camera, corresponding to APP Store or Google Play Store and
download the “WIFI UAV” application for free
Step 1: Download the app
IOS Device
Android Device
Google Play

*Gravity Mode:Gravity Mode:
In this mode, as the phone tilts and swings forward, the aircraft will be induced by the movement to
fly forward. As the phone tilts and swings to the right, the aircraft will be induced by the movement to
fly to the right.
*Video with music :
Click the MV and select one song after taking off the drone, then start to record a video.
www.bai-chun.com