Bakeey TS-WP10 User manual

TS-WP10 User Manual

TS-WP10 Bathroom Clock:Display of all functionsSM
AM
PM
12
H ALoLAL
MIN
MAX
H ALoLAL
MIN
MAX
1

Meanings of display:Time display modeCountdown display mode
SM
H ALoLAL
H ALoLAL
H ALoLAL
MIN
H ALoLAL
MIN
AM
1
TemperatureHumidityMax./Min. valuesAlarm iconAlarm clock iconSnooze iconTime iconA.M./P.M.Time displayDynamic clockCountdownMinuteSecondCountdown iconDynamic seconds countdownTemperature unit2

Buttons:
++MODE+
-
ALERTMAXMINC/F
SNOOZE/LIGHTCLEAR101Start countdownStart countdownOne-button snooze/turn on backlightMode selectionBeyond-limit alarm settingsView max./min. valuesForward adjustmentBackward adjustment°C/°F switch
++
Foldable supportRevolving clip-on rear coverWall mountingholeTransparent silicone suction cup3

Thank you for purchasing the TS-WP10 bathroom clock. The user’s guide for operations is given as follows:1.Major functions:Hour, minute, second, temperature, humidity, and simulated time are displayed on the same screenTwo alarm clocksSnooze function: Five minutes by defaultCountdown functionDynamic countdown progress bar indicatorDynamic seconds countdown indicatorIndoor temperature (measuring range: 0°C~50°C/32°F~122°F); refreshing interval: 30s. Resolution: 0.1°C.Indoor humidity (measuring range: 20%~99%); refreshing interval: 30s. Resolution: 1%.Max./Min. values of indoor temperature/humiditySet up beyond-limit values of indoor temperature/humidity4

2.Power supply:Backlight color prompt for beyond-limit temperature/humidityTemperature/Humidity calibration functionWaterproof grade: IPX4 1. Power supply through USB DC power cable(when the DC cable is plugged in, the backlight indicator turns on for 8 seconds, and then automatically dies out if no buttons are pressed. To keep the backlight indicator constantly on, long press [CLEAR] for at east 2 seconds until the beep sound is heard, andthen enable Always On of the backlight indicator. To disable Always On of the backlight indicator, long press [CLEAR] for at least 2 seconds until the beep sound is heard, and then disable Always On. During the countdown and alarming periods, the backlight indicator is always on, regardless of whether the DC cable is plugged in or not.5

2. Powered by 3 AAA batteries (the clock is not always on when powered by batteries).Remarks: This clock is shipped without batteries.
++MODE+
-
ALERTMAXMINC/F
1.5V SIZE “AAA”/AM4 LRO031.5V SIZE “AAA”/AM4 LRO031.5V SIZE “AAA”/AM4 LRO03
USB DC power cableAAA battery * 36

3. Power on and reset: When this clock is powered on, the LED is fully displayed for 3 seconds, and the backlight color alternates in the order of red, orange, and white for one cycle. The initial interface of the system is displayed after a beep sound.Default display after startup: white backlightTime: 0:00Default time format: 24 hoursDefault units: Temperature [°C]; relative humidity: [%]7

4. Time settings: In the time display mode, jump to the setup page by long pressing [MODE], when the parameters to be set up are displayed and flashing; the setup sequence is: 12HR/24HR→hour→minute→exit and return to normal time display. In time settings, short press [＋] if you want to add the value by 1 or long press [] for quick increase (8 steps/s); short press [－] if you want to decrease the value by 1, or long press [－] for quick decrease (8 steps/s).＋5. Alarm clock settings: In the time display mode, short pressing [MODE] results in a switch to the alarm clock display interface. The switching sequence is: Normal time display→Alarm Clock 1→Alarm Clock 2→Normal time display.8

In the alarm clock review mode, the alarm clock can be turned on or off by short pressing [＋]. During setting, select 1 alarm clock and long press [MODE] for at least 3 seconds, when the Hour place starts flashing; then short press [MODE] and the Minute place starts flashing. Short press [＋] if you want to increase the value by 1, or long press [＋] for quick increase (8 steps/s); short press 【－】 if you want to decrease the value by 1, or long press [－] for quick decrease (8 steps/s). Short press [MODE] to automatically save settings and exit.9