Ballard Designs LO472 User manual

PRODUCT NAME: Solar Outdoor Lantern
ITEM NUMBER: LO472
ASSEMBLED DIMENSIONS: 14” H x 10” Diameter or 10”H x 10” Diameter
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
Page 1 of 3
MADE IN CHINA
IMPORTANT SAFETY INSTRUCTIONS:
-For your safety, please completely read Instruction Sheet before using lamp.
-Keep product out of reach of children.
-Do not remove screws or open lamp.
-Do not leave lamp outside in heavy rain. Protect from excessive moisture.
-Charge lamp in direct sunlight (Lamp must be OFF) or use DC-USB (included).
-Disconnect from charger when not in use.
-Do not drop or place heavy objects on lamp.
-Do not use lamp if cracked or broken.
WARNING:
-Built-in rechargeable battery is not replaceable.
-Do not remove or replace battery.
-Do not dispose lamp into trash. Refer to local regulations for proper disposal.
-Battery should be fully discharged before disposal.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
UPDATED: 12-20-2022

NOTE: Remove all parts from the box along
with any plastic protective packaging and carefully lay all the
parts out on a clean, flat surface.
DO NOT discard any contents until after assembly and
installation is complete to avoid accidentally discarding small
parts or hardware.
Recommended Location for Use: Indoor/Outdoor Environment
Charging Time: Approximately 5 Hours via USB; 12 hours via solar.
Running Time: 2.5 hours@300 lumens; 3.5 hours@200 lumens; 7 hours@100 lumens
PARTS
Check to make sure you have the following:
INCLUDED:
Page 2 of 3
1- Light (A) 1- DC - USB Cord (B)
ENVIRONMENTAL PROTECTION:
The symbol on the product dictates that Waste electrical products should not be disposed of
with household waste. Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
Cleaning and Care
Periodically dust with a soft, dry cloth.
Protect surfaces to prevent damage.
Do not use alcohol based cleaners or polishers.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Page 3 of 3
FCC INSTRUCTION:
Caution: Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Do Not Charge in Rain or Water
Electrical Shock Hazard
Charge in a Dry Indoor Evironment
WARNING
STEP 1: INSTALL CABLE AND CHARGE LAMP
- Connect USB Cable to a computer or any 5V OUTPUT USB charging unit.
- Insert other end of Cable into DC port on Lamp (A)
- Charge for 5-6 hours (or until fully charged) prior to use.
- Indicator light is RED during CHARGING and GOES OUT when CHARGING IS COMPLETE.
(A)
5v Output
STEP 2: POWERING LAMP
Turn On: Press and hold on/off button for 3 to 5 seconds.
Turn Off: Press and hold on/off button for 3 to 5 seconds.
Adjust Brigtness: Low-Medium-High, quickly press and release.
ON/OFF BUTTON
CHARGING PORT
SOLAR CHARGING: Lamp must be OFF