Ballard Designs VERANO 3 User manual

PRODUCT NAME: VERANO 3 LIGHT OUTDOOR WALL SCONCE
ITEM NUMBER: LO410 3
DIMENSIONS OF ITEM ASSEMBLED: 10”W x 18.5”H x 12” E
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE. Page 1 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN CHINA
IMPORTANT SAFETY INSTRUCTIONS:
-We strongly recommend that a professional electrician install all direct wire fixtures.
-These Assembly Instructions are provided for your safety. It is important that they are read carefully
and completely before assembling this Fixture.
-This product must be installed with the applicable installation code by a person familiar with the
construction and operation of the product.
-This Fixture has been rated for up to 60 Watt MAX Type B Candelabra Bulb (NOT Included).
-Before starting installation of this Fixture or the removal of a previous fixture, disconnect the power
by turning off the circuit breaker or removing the fuse from the fuse box.
WARNING:
-Deviation from the Assembly Instructions may result in a risk of fire or electric shock.
-To reduce risk of fire, electrical shock, or personal injury, always turn off and unplug Fixture and
allow it to cool prior to replacing the bulb.
-Do not touch the bulb when the Fixture is turned on. Do not look directly at the lit bulb.
-Keep flammable material away from the lit bulb.

NOTE: Remove all parts and hardware from the box along
with any plastic protective packaging and carefully lay all the parts
out on a clean, flat surface.
DO NOT discard any contents until after assembly and
installation is complete to avoid accidently discarding small
parts or hardware.
Recommended Location for Use: Wet Location
Assembly Time: 15 Minutes
People Required: 1 or More People
Tools Required: Screwdriver, Wire Strippers,
Wire Cutters, Electrical Tape
PARTS
Check to make sure you have the following:
Page 2 of 4
INCLUDED:
NOTE: The Mounting Strap comes attached to the Fixture Body.
3- Wire Connectors (D)
2- Outlet Box Mounting
Screws (B)
1- Fixture Body (A)
NOT INCLUDED:
3- 60 Watt Max
Type B Candelabra Bulb
2- Ball nut (E)
1- Mounting Strap (C)
Fixture Body (A)

Page 3 of 4
STEP 1:
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 2:
NOTE: Before starting installation of this Fixture or the removal of a previous Fixture,
disconnect the power by turning off the circuit breaker or removing the fuse from the fuse box.
Attach the Mounting Strap (C) to the Outlet
Box using the Outlet Box Mounting Screws
(B).
(C)
(B)
Wrap the Ground Wire from the Fixture around
the Ground Screw on the Mounting Strap (C) and
then connect the two White Wires from the Fixture
to the White Wire (neutral wire) from the Outlet
Box. Connect the Black Wires from the Fixture
to the Black Wire (live wire) from the Outlet Box.
Cover the connections using the Wire
Connectors (D).
NOTE: Black Outlet Box Wires may be red or
smooth. White Outlet Box Wires may be ribbed.
WHITE OR RIBBED
BLACK WIRE
FROM HOUSE
WHITE OR RIBBED
FROM FIXTURE
FROM HOUSE
FROM FIXTURE
BLACK OR SMOOTH
(D)
(C)

STEP 3:
Attach the Fixture Body (A) to the Mounting
Plate (C) by screwing on the Ball nut (E).
Page 4 of 4
STEP 6:
Connect breaker and turn on light.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Cleaning & Care:
To clean, wipe the Fixture with a soft, dry
cloth.Avoid the use of harsh or abrasive chemicals
as they may damage the finish.
NOTE: Before starting installation of this Fixture or the removal of a previous Fixture,
disconnect the power by turning off the circuit breaker or removing the fuse from the fuse box.
STEP 4:
Install light bulb(not included).Use maximum
bulb 60W Type B incandescent bulb or CFL
equivalent.
(E)
(C)
STEP 5:
After securing fixture to the wall it is recommended
that the gap between the wall and fixture backplate
be sealed with any good quality waterproof caulk or
silicone sealant (not included).
(A)