B&B Electronics BB-USR604 User manual

Install the Drivers
1
3
2Set DIP Switches
4Connect the Converter
Product Overview
Serial
Ports
LEDs
Power the Converter
USB
Port
The USR602 can run on 5 V USB power if the host
port is providing 500 mA. It can also be powered
via the terminal block or barrel jack port.
Set the converter to RS-232 mode using the DIP
switches. Loopback pins 2 and 3. Using Hyper Termi-
nal or similar program, connect to the COM port. Set
the desired baud rate. Ensure that Hyper Terminal
local echo is OFF. Transmit data. If the same character
string is returned, the test is good.
DIP
Switches
Terminal block
and barrel jack
To prevent installation errors, do not plug in the hard-
ware until you have already installed the drivers.
Use the included CD to install the converter’s drivers in
the attached PC.
When you connect the converter to the host
computer’s USB port the Found New Hardware
wizard will open. It will discover and install the
USB device. Then it will discover and install each
serial port. Allow Windows to install the converter
“Automatically.” There is no need to connect to the
Internet or Windows Update.
If a popup window says the software has not passed
Windows logo testing, that’s OK. Just click on
“Continue Anyway.”
When the wizard is complete the serial ports on the
converter will appear in Windows Device Manager
as new COM ports.
5Configure the Serial Ports
Open Control Panel. Click “System” to open the
Device Manager. Under “Ports,” double-click the
port to be configured.
On the “Serial Port Properties” window, set the
required communications parameters for the system
with which you are communicating. If necessary,
6Loopback Test
7LEDs
LED
Type Indication when ON
PWR
Computer is receiving adequate
voltage and current from USB or
power source
TX Serial interface is transmitting data
RX Serial interface is receiving data
click Advanced and set up the Advanced Properties.
(Refer to manual for more information.)
DIP
Switches SW# RS-232 RS-422 RS-485
4-Wire
RS-485
2-Wire
Port 1 1 Off ON Off ON
2 Off ON ON Off
Port 2 3 Off ON Off ON
4Off ON ON Off

Troubleshooting
Fast, Easy Answers
One USB port is required for each installed device.
The USB port can be native to the PC or it can be a
USB port on a USB hub that is connected to a PC.
The device works with USB 1.1 or 2.0 ports. But it
has a maximum USB data rate of 12 Mbps.
To verify the installation you may open the Windows
Device Manager. Scroll down to Ports. Expand the
flyout window. You should see the new ports. If there
are no exclamation points or other trouble indicators
the ports are installed correctly and ready for use.
Sleep & Hibernate: Windows 7 disables USB transmit
while in Sleep & Hibernate.
Terminal Block
One conductor per terminal.
Use copper wire only.
Wire size 16 to 28 AWG.
Tightening torque 5 KG -CM.
Wire temperature rating: 105 °C
(Sized for 60 °C ampacity
Fast and easy on the web: www.bb-elec.com
Two-port USB to
Serial Converter
USR602
© 2011 B&B Electronics Manufacturing Company
1-888-948-2248 | Europe: [phone]
www.bb-elec.com
Recommended Accessories
Please double check
S t e p 7.
You can also use your
smart phone to access
complete documentation
on our website. Simply
scan the code to the right.
PS12VLB-INT-MED
Power Supply
http://www.bb-elec.com/
product_multi_family.asp?
MultiFamilyId=133&Trail=
16&TrailType=Top
MDR-20-24
DIN rail mount
power supply
http://www.bb-elec.com/
product_multi_family.asp?
MultiFamilyId=133&Trail=
16&TrailType=Top
USR602
Two Meter USB Cable
Panel mount adapters
DIN rail mount adapter
CD ROM with Drivers
First Things First...
Before you begin, be sure you have
the following:
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: [phone] | Fax: [phone]
www.bb-elec.com | E-mail: [email protected]
•
•
Quick
Start
Guide
Information - FCC rules
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference that may
cause undesired operation.
Information - UL Class 1 Div 2
Suitable for use in Class 1, Division 2, Groups A, B, C and
D Hazardous Locations, or Nonhazardous locations only.
WARNING - EXPLOSION HAZARD – DO NOT
DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS LIVE
UNLESS THE AREA IS KNOWN TO BE FREE OF
IGNITABLE CONCENTRATIONS.
Install in accordance with control drawing
number 9340R0.
Ind. Cont. Eq.
For HAZ LOC
3HTV
E245458
Class I, Div. 2, Groups A, B, C & D
Temp. Code: T4A
Document number – PN8940_R004_USR602_4712qsg